Li-ion Battery Separators, Mechanical Integrity and Failure Mechanisms Leading to Soft and Hard Internal Shorts

Separator integrity is an important factor in preventing internal short circuit in lithium-ion batteries. Local penetration tests (nail or conical punch) often produce presumably sporadic results, where in exactly similar cell and test set-ups one cell goes to thermal runaway while the other shows minimal reactions. We conducted an experimental study of the separators under mechanical loading, and discovered two distinct deformation and failure mechanisms, which could explain the difference in short circuit characteristics of otherwise similar tests. Additionally, by investigation of failure modes, we provided a hypothesis about the process of formation of local “soft short circuits” in cells with undetectable failure. Finally, we proposed a criterion for predicting onset of soft short from experimental data.

[1]  T. Wierzbicki,et al.  Calibration and finite element simulation of pouch lithium-ion batteries for mechanical integrity , 2012 .

[2]  Craig B. Arnold,et al.  Mechanical Properties of a Battery Separator under Compression and Tension , 2014 .

[3]  Tomasz Wierzbicki,et al.  Characterization of plasticity and fracture of shell casing of lithium-ion cylindrical battery , 2015 .

[4]  Tomasz Wierzbicki,et al.  Modelling of cracks developed in lithium-ion cells under mechanical loading , 2015 .

[5]  Tao Sun,et al.  Deformation and fracture behaviors of microporous polymer separators for lithium ion batteries , 2014 .

[6]  Xiaosong Huang,et al.  Separator technologies for lithium-ion batteries , 2011 .

[7]  Craig B. Arnold,et al.  A Model for the Behavior of Battery Separators in Compression at Different Strain/Charge Rates , 2014 .

[8]  Elham Sahraei,et al.  Microscale failure mechanisms leading to internal short circuit in Li-ion batteries under complex loading scenarios , 2016 .

[9]  Ozan Toprakci,et al.  A review of recent developments in membrane separators for rechargeable lithium-ion batteries , 2014 .

[10]  A. Ajji,et al.  Fabrication of microporous membranes from melt extruded polypropylene precursor films via stretching: Effect of annealing , 2015, Chinese Journal of Polymer Science.

[11]  Richard S. Baldwin,et al.  Battery Separator Characterization and Evaluation Procedures for NASA's Advanced Lithium-Ion Batteries , 2010 .

[12]  Xiaosong Huang,et al.  Modeling stresses in the separator of a pouch lithium-ion cell , 2011 .

[13]  T. Wierzbicki,et al.  Homogenized mechanical properties for the jellyroll of cylindrical Lithium-ion cells , 2013 .

[14]  Shengbo Zhang.  A review on the separators of liquid electrolyte Li-ion batteries , 2007 .

[15]  Elham Sahraei,et al.  Deformation and failure characteristics of four types of lithium-ion battery separators , 2016 .

[16]  Xiaowei Chen,et al.  A semi-quantitative deformation model for pore formation in isotactic polypropylene microporous membrane , 2015 .

[17]  Azadeh Sheidaei,et al.  Mechanical behavior of a battery separator in electrolyte solutions , 2011 .

[18]  Xuning Feng,et al.  Characterization of penetration induced thermal runaway propagation process within a large format lithium ion battery module , 2015 .

[19]  T. Wierzbicki,et al.  Modeling and short circuit detection of 18650 Li-ion cells under mechanical abuse conditions , 2012 .

[20]  T. Wierzbicki,et al.  Characterizing and modeling mechanical properties and onset of short circuit for three types of lithium-ion pouch cells , 2014 .

[21]  Yong Xia,et al.  Damage of cells and battery packs due to ground impact , 2014 .

[22]  K. Kozaczek,et al.  The Effect Of Annealing On , 1997, 1997 IEEE International Magnetics Conference (INTERMAG'97).

[23]  Pankaj Arora,et al.  Battery separators. , 2004, Chemical reviews.