Surface modification by electrical discharge machining: A review

The last decade has seen an increasing interest in the novel applications of electrical discharge machining (EDM) process, with particular emphasis on the potential of this process for surface modification. Besides erosion of work material during machining, the intrinsic nature of the process results in removal of some tool material also. Formation of the plasma channel consisting of material vapours from the eroding work material and tool electrode; and pyrolysis of the dielectric affect the surface composition after machining and consequently, its properties. Deliberate material transfer may be carried out under specific machining conditions by using either composite electrodes or by dispersing metallic powders in the dielectric or both. This paper presents a review on the phenomenon of surface modification by electric discharge machining and future trends of its applications.

[1]  K. Furutani,et al.  A New Process of Additive and Removal Machining by EDM with a Thin Electrode , 2000 .

[2]  F. Klocke,et al.  The effects of powder suspended dielectrics on the thermal influenced zone by electrodischarge machining with small discharge energies , 2004 .

[3]  E. C. Jameson,et al.  DESCRIPTION AND DEVELOPMENT OF ELECTRICAL DISCHARGE MACHINING , 2001 .

[4]  Pei-Jen Wang,et al.  Predictions on surface finish in electrical discharge machining based upon neural network models , 2001 .

[5]  Elman C Jameson,et al.  Electrical Discharge Machining , 2001 .

[6]  B. Yan,et al.  Surface modification of Al–Zn–Mg alloy by combined electrical discharge machining with ball burnish machining , 2002 .

[7]  P. Dumas,et al.  Investigation into Application of Electrodischarge Machining as Steel Surface Modification Technique , 1998 .

[8]  M. Shunmugam,et al.  Improvement of wear resistance by EDM with tungsten carbide P/M electrode , 1994 .

[9]  G. Wollenberg,et al.  Influence of selected groups of additives on breakdown in EDM sinking , 2004 .

[10]  B. Yan,et al.  Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric , 2005 .

[11]  Y. Wong,et al.  Near-mirror-finish phenomenon in EDM using powder-mixed dielectric , 1998 .

[12]  Elsa Henriques,et al.  Effect of the powder concentration and dielectric flow in the surface morphology in electrical discharge machining with powder-mixed dielectric (PMD-EDM) , 2008 .

[13]  Masanori Kunieda,et al.  Electrical Discharge Machining in Gas , 1997 .

[14]  Yan Cherng Lin,et al.  Surface Improvement Using a Combination of Electrical Discharge Machining with Ball Burnish Machining Based on the Taguchi Method , 2001 .

[15]  Biing-Hwa Yan,et al.  EDM performance of Cr/Cu-based composite electrodes , 2003 .

[16]  Mukund R. Patel,et al.  Theoretical models of the electrical discharge machining process. II. The anode erosion model , 1989 .

[17]  H. Narumiya.  EDM by powder suspended working fluid , 1989 .

[18]  Y. Zvirin,et al.  Melting and Evaporation Phenomena During Electrical Erosion , 1975 .

[19]  Stephen T. Newman,et al.  State of the art electrical discharge machining (EDM) , 2003 .

[20]  B. Schumacher.  After 60 years of EDM the discharge process remains still disputed , 2004 .

[21]  Zhenlong Wang,et al.  Instantaneous fabrication of tungsten microelectrode based on single electrical discharge , 2005 .

[22]  Biing-Hwa Yan,et al.  Surface modification of Al–Zn–Mg aluminum alloy using the combined process of EDM with USM , 2001 .

[23]  A. Curodeau,et al.  New EDM polishing and texturing process with conductive polymer electrodes , 2005 .

[24]  M. S. Shunmugam,et al.  Surface modification in electrodischarge processing with a powder compact tool electrode , 1991 .

[25]  David K. Aspinwall,et al.  Workpiece surface modification using electrical discharge machining , 2003 .

[26]  Yoke San Wong,et al.  Effects of flushing on electro-discharge machined surfaces , 1995 .

[27]  Partha Saha,et al.  Surface modification of C40 steel using WC-Cu P/M green compact electrodes in EDM , 2010, Int. J. Manuf. Technol. Manag..

[28]  Y. Wong,et al.  EDM performance of TiC/copper-based sintered electrodes , 2001 .

[29]  Fu-Chen Chen,et al.  Investigation into some surface characteristics of electrical discharge machined SKD-11 using powder-suspension dielectric oil , 2005 .

[30]  C. Wykes,et al.  A new method of optimising material removal rate using EDM with copper–tungsten electrodes , 2000 .

[31]  M. L. Jeswani,et al.  Effect of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining , 1981 .

[32]  C. Bai,et al.  Effects of kerosene or distilled water as dielectric on electrical discharge alloying of superalloy Haynes 230 with Al–Mo composite electrode , 2006 .

[33]  V. K. Jain,et al.  ANALYSIS OF SPARK PROFILES DURING EDM PROCESS , 1997 .

[34]  Yih-fong Tzeng,et al.  Effects of Powder Characteristics on Electrodischarge Machining Efficiency , 2001 .

[35]  Wansheng Zhao,et al.  Surface modification process by electrical discharge machining with a Ti powder green compact electrode , 2002 .

[36]  L. Froyen,et al.  Study of the white layer of a surface machined by die sinking electro discharge machining , 1995 .

[37]  Pradeep Kumar,et al.  PARAMETRIC OPTIMIZATION OF POWDER MIXED ELECTRICAL DISCHARGE MACHINING BY RESPONSE SURFACE METHODOLOGY , 2005 .

[38]  Mathews P. Samuel,et al.  Power metallurgy tool electrodes for electrical discharge machining , 1997 .

[39]  Sehijpal Singh,et al.  Application of Taguchi method for optimisation of powder mixed electrical discharge machining , 2005, Int. J. Manuf. Technol. Manag..

[40]  David K. Aspinwall,et al.  Electrical Discharge Surface Alloying of Ti and Fe Workpiece Materials Using Refractory Powder Compact Electrodes and Cu Wire , 2003 .

[41]  Ching-Tien Lin,et al.  Surface modification using semi-sintered electrodes on electrical discharge machining , 2008 .

[42]  Naotake Mohri,et al.  Surface modification of aluminum by electrical discharge alloying , 1994 .

[43]  L. C. Lee,et al.  Quantification of surface damage of tool steels after EDM , 1988 .

[44]  O. A. Abu Zeid,et al.  On the effect of electrodischarge machining parameters on the fatigue life of AISI D6 tool steel , 1997 .

[45]  David K. Aspinwall,et al.  Surface alloying using PM composite electrode materials when electrical discharge texturing hardened AISI D2 , 2002 .

[46]  S. Basu,et al.  Electron microprobe study of deposition and diffusion of tool material in electrical discharge machining , 1979 .

[47]  E. Henriques,et al.  Influence of silicon powder-mixed dielectric on conventional electrical discharge machining , 2003 .

[48]  Masanori Kunieda,et al.  Advancing EDM through fundamental insight into the process , 2005 .

[49]  J. S. Soni,et al.  Experimental investigation on migration of material during EDM of die steel (T215 Cr12) , 1996 .

[50]  W. Zhao,et al.  The application of research on powder mixed EDM in rough machining , 2002 .

[51]  L. Dabrowski,et al.  Study of electrical discharge machining using powder-suspended working media , 2003 .

[52]  J. McGeough.  Advanced Methods Of Machining , 1988 .

[53]  M. Barash,et al.  Experiments with electric spark toughening , 1964 .

[54]  Mukund R. Patel,et al.  Theoretical models of the electrical discharge machining process. III. The variable mass, cylindrical plasma model , 1993 .

[55]  Naotake Mohri,et al.  Metal Surface Modification by Electrical Discharge Machining with Composite Electrode , 1993 .

[56]  B. Yan,et al.  The effect in EDM of a dielectric of a urea solution in water on modifying the surface of titanium , 2005 .

[57]  N. Mohri,et al.  Layer Generation Process on Work-piece in Electrical Discharge Machining , 2003 .

[58]  Fritz Klocke,et al.  Surface and sub-surface quality in material removal processes for tool making , 1998 .

[59]  Taylan Altan,et al.  Advanced Techniques for Die and Mold Manufacturing , 1993 .

[60]  N. Mohri,et al.  Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid , 2001 .

[61]  D. Aspinwall,et al.  Electrical discharge surface alloying , 2004 .