Flow patterns and mixing mechanisms in the screw mixing element of a co‐rotating twin‐screw extruder

Non-Newtonian and non-isothermal flow simulations based on 3-D FEM were applied to a special and conventional elements of a twin-screw extruder. The screw mixing element (SME), a kind of special element, was a distributive mixing promoter consisting of a standard screw profile with slots cut across the flight tip to increase leakage flow. The full flight screw (FF) and the kneading block (KB) were examined as conventional elements in order to contrast the mixing behavior with the SME. The accuracy of numerical results was verified by experimentally measuring pressure and temperature. Additionally, marker particle tracking analysis was carried out to evaluate the distributive and dispersive mixing. Using the above analyses, the following results were obtained: The pumping capability of the SME was smaller than that of the FF and was the same as for the KB. The SME suppressed heat generation and showed the lowest temperature distribution of the three elements. For distributive mixing, the SME showed the best performance judging from the mixing coefficient G, residence time distribution, and area stretch distribution based on a laminar mixing mechanism. A higher rotational speed achieved better distributive mixing performance. For dispersive mixing defined by stress distribution, the SME showed the second best performance next to the KB. It also showed better dispersive mixing performance with increasing rotational speed. The SME had the advantages of low heat generation and good distributive mixing.

[1]  I. Manas‐Zloczower,et al.  Analysis of Mixing Performance in a VIC Mixer , 1994 .

[2]  K. Funatsu,et al.  Mixing mechanism of three‐tip kneading block in twin screw extruders , 2000 .

[3]  Y. Rubin,et al.  Analysis of Mixing in Corotating Twin Screw Extruders through Numerical Simulation , 2000 .

[4]  D. Todd.  Residence time distribution in twin-screw extruders , 1975 .

[5]  Kazumori Funatsu,et al.  Numerical study of twin‐screw extruders by three‐dimensional flow analysis—development of analysis technique and evaluation of mixing performance for full flight screws , 1996 .

[6]  D. Reinelt,et al.  Melt Conveying in Co-rotating Twin Screw Extruders , 2000 .

[7]  James L White,et al.  Modelling Flow in an Intermeshing Co-rotating Twin Screw Extruder: Flow in Kneading Discs , 1987 .

[8]  Kazumori Funatsu,et al.  3-D non-isothermal flow field analysis and mixing performance evaluation of kneading blocks in a co-rotating twin srew extruder , 2001 .

[9]  P. Andersen,et al.  Experimental Studies for Optimizing Screw and Die Design When Compounding Fiberglass Strand on the Co-Rotating Twin Screw Extruder , 1993 .

[10]  H. Potente,et al.  Design of Tightly Intermeshing Co-Rotating Twin Screw Extruders , 1994 .

[11]  Z. Tadmor,et al.  Theoretical model for non-intermeshing twin screw extruders , 1974 .

[12]  Kazumori Funatsu,et al.  3‐D numerical simulations of nonisothermal flow in co‐rotating twin screw extruders , 2000 .

[13]  Han E. H. Meijer,et al.  The modeling of continuous mixers. Part I: The corotating twin-screw extruder , 1988 .

[14]  L. Delamare,et al.  A global computer software for polymer flows in corotating twin screw extruders , 1998 .

[15]  Julio M. Ottino,et al.  A framework for description of mechanical mixing of fluids , 1981 .

[16]  Andrew N. Hrymak,et al.  Numerical simulation of pressure and velocity profiles in kneading elements of a co‐rotating twin screw extruder , 2000 .