MADE3D: Enabling the next generation of high-torque density wind generators by additive design and 3D printing

[1]  Fan Wu,et al.  Towards Fully Additively-Manufactured Permanent Magnet Synchronous Machines: Opportunities and Challenges , 2019, 2019 IEEE International Electric Machines & Drives Conference (IEMDC).

[2]  Shinji Wakao,et al.  Improvement of Torque Characteristics For a Synchronous Reluctance Motor Using MMA-based Topology Optimization Method , 2018, IEEE Transactions on Magnetics.

[3]  Masafumi Fujita,et al.  A topology optimization method for electric machines and devices through submodular maximization , 2019, Electronics and Communications in Japan.

[4]  M. Mihai,et al.  Additive manufacturing of soft and hard magnetic materials used in electrical machines , 2020 .

[5]  Hajime Igarashi,et al.  Multimaterial Topology Optimization of Electric Machines Based on Normalized Gaussian Network , 2015, IEEE Transactions on Magnetics.

[6]  Tomi Lindroos,et al.  Impact of Topology Optimization Problem Setup on Switched Reluctance Machine Design , 2019, 2019 22nd International Conference on the Computation of Electromagnetic Fields (COMPUMAG).

[7]  Hajime Igarashi,et al.  Topology Optimization of Synchronous Reluctance Motor Using Normalized Gaussian Network , 2015, IEEE Transactions on Magnetics.

[8]  Yaoyao Fiona Zhao,et al.  A survey of the design methods for additive manufacturing to improve functional performance , 2016 .

[9]  Fan Wu,et al.  High-Torque-Density Low-Cost Magnetic Gear Utilizing Hybrid Magnets and Advanced Materials , 2019, 2019 IEEE International Electric Machines & Drives Conference (IEMDC).

[10]  Rafal Wrobel,et al.  A Comprehensive Review of Additive Manufacturing in Construction of Electrical Machines , 2020, IEEE Transactions on Energy Conversion.

[11]  Yoshifumi Okamoto,et al.  Parallelization of Preconditioned MRTR Method With Eisenstat’s Technique by Means of Algebraic Multicolor Ordering , 2015, IEEE Transactions on Magnetics.

[12]  Jianguo Zhu,et al.  A Review of Design Optimization Methods for Electrical Machines , 2017 .

[13]  Gary Muller,et al.  Prospects of additive manufacturing of rare-earth and non-rare-earth permanent magnets , 2018 .

[14]  E. Lara‐Curzio,et al.  Additive manufacturing of highly dense anisotropic Nd–Fe–B bonded magnets , 2020, Scripta Materialia.

[15]  Kota Watanabe,et al.  Topology Optimization Based on the ON/OFF Method for Synchronous Motor , 2018, IEEE Transactions on Magnetics.

[16]  Grace X. Gu,et al.  Generative Deep Neural Networks for Inverse Materials Design Using Backpropagation and Active Learning , 2020, Advanced science.

[17]  Milorad Risticevic,et al.  Topological Approach for Minimization of Cogging Torque in Permanent Magnet Synchronous Motors , 2020 .

[18]  Hajime Igarashi,et al.  Topology Optimization Accelerated by Deep Learning , 2019, IEEE Transactions on Magnetics.

[19]  Alasdair McDonald,et al.  On the Optimization of Generators for Offshore Direct Drive Wind Turbines , 2017, IEEE Transactions on Energy Conversion.

[20]  P Jaen-Sola,et al.  Design of direct-drive wind turbine electrical generator structures using topology optimization techniques , 2020, Journal of Physics: Conference Series.

[21]  H. Igarashi,et al.  Multi-Objective Topology Optimization of Rotating Machines Using Deep Learning , 2019, IEEE Transactions on Magnetics.

[22]  Hajime Igarashi,et al.  Topology optimization of IPM motor with aid of deep learning , 2019 .

[23]  L. Fingersh,et al.  Additive Manufacturing: A New Paradigm for the Next Generation of High-Power-Density Direct-Drive Electric Generators , 2018, Volume 2: Heat Exchanger Technologies; Plant Performance; Thermal Hydraulics and Computational Fluid Dynamics; Water Management for Power Systems; Student Competition.

[24]  Nurul Azim Bhuiyan,et al.  Optimization of Offshore Direct Drive Wind Turbine Generators With Consideration of Permanent Magnet Grade and Temperature , 2019, IEEE Transactions on Energy Conversion.

[25]  S. Andreev,et al.  Additive manufacturing of heavy rare earth free high-coercivity permanent magnets , 2020 .

[26]  Hajime Igarashi,et al.  Transfer Learning Through Deep Learning: Application to Topology Optimization of Electric Motor , 2020, IEEE Transactions on Magnetics.

[27]  C. Wang,et al.  Machine learning in additive manufacturing: State-of-the-art and perspectives , 2020, Additive Manufacturing.

[28]  J. Lamarre,et al.  Novel Multi-layer Design and Additive Manufacturing Fabrication of a High Power Density and Efficiency Interior PM Motor , 2020, 2020 IEEE Energy Conversion Congress and Exposition (ECCE).