Web crippling capacities of fastened aluminium lipped channel sections subjected to one-flange loading conditions

Abstract Recently, a new generation of roll-formed aluminium sections have been produced by BlueScope Permalite Australia and utilized in structural systems. However, limited research has been conducted to investigate their buckling instabilities including web crippling failure. The empirical nature of the current design guidelines may also lead to inaccurate estimation to their web crippling capacities. Therefore, this study aims to investigate the web crippling behaviour of and the design considerations for roll-formed aluminium lipped channel (ALC) sections using a combination of experimental study and finite element analysis (FEA). In total, 40 ALC specimens were tested under one-flange loading conditions with flanges being restrained to the supports (Fastened). Non-linear finite element models were also developed and validated against the experiments. An extensive parametric study was subsequently conducted to extend the range of geometrical dimensions and aluminium alloy grades of ALC sections. Further, the applicability and accuracy of the design rules given in the American, Australian, and European specifications were assessed. It was found that most of these guidelines yield either unconservative or over-conservative predictions of the ultimate web crippling capacities, and hence suitable modifications were proposed. Predictions due to the modified design rules showed a good agreement with both experimental and numerical results, and are hence recommended to be incorporated in relevant aluminium standards.

[1]  Asraf Uzzaman,et al.  Effect of web holes on web crippling strength of cold-formed steel channel sections under end-one-flange loading condition - Part II: Parametric study and proposed design equations , 2016 .

[2]  Mahen Mahendran,et al.  Bearing capacity of cold‐formed unlipped channels with restrained flanges under EOF and IOF load cases , 2015 .

[3]  Ben Young,et al.  The continuous strength method for the design of aluminium alloy structural elements , 2016 .

[4]  Mahen Mahendran,et al.  Web crippling experiments of high strength lipped channel beams under one-flange loading , 2017 .

[5]  Yu Chen,et al.  Aluminum tubular sections subjected to web crippling , 2015 .

[6]  James B. P. Lim,et al.  Web Crippling Behavior of Unlipped Cold-Formed Ferritic Stainless Steel Channels Subject to One-Flange Loadings , 2018, Journal of Structural Engineering.

[7]  Gregory J. Hancock,et al.  Design of Cold-Formed Channels Subjected to Web Crippling , 2001 .

[8]  Asraf Uzzaman,et al.  Web crippling behaviour of cold-formed steel channel sections with web holes subjected to interior-one-flange loading condition – Part II: parametric study and proposed design equations , 2017 .

[9]  Asraf Uzzaman,et al.  Effect of web holes on web crippling strength of cold-formed steel channel sections under end-one-flange loading condition – Part I: Tests and finite element analysis , 2016 .

[10]  Poologanathan Keerthan,et al.  Experimental study on web crippling strength of hollow flange channels under end-one-flange and interior-one-flange load cases , 2016 .

[11]  Konstantinos Daniel Tsavdaridis,et al.  Web crippling behaviour and design of aluminium lipped channel sections under two flange loading conditions , 2019, Thin-Walled Structures.

[12]  Poologanathan Keerthan,et al.  Experimental study of aluminium lipped channel sections subjected to web crippling under two flange load cases , 2019, Thin-Walled Structures.

[13]  Gregory J. Hancock,et al.  Direct Strength Design of Cold-Formed C-Sections for Shear and Combined Actions , 2012 .

[14]  K. Poologanathan,et al.  Experimental study of roll-formed aluminium lipped channel beams in shear , 2020 .

[15]  K. Rasmussen,et al.  Mechanical properties and residual stresses in cold-rolled aluminium channel sections , 2019, Engineering Structures.

[16]  Konstantinos Daniel Tsavdaridis,et al.  Numerical investigation of web crippling in fastened aluminium lipped channel sections under two-flange loading conditions , 2020, Structures.

[17]  Mahen Mahendran,et al.  Numerical modelling of web crippling failures in cold-formed steel unlipped channel sections , 2019, Journal of Constructional Steel Research.

[18]  Poologanathan Keerthan,et al.  New design rules for lipped channel beams subject to web crippling under two-flange load cases , 2017 .

[19]  Mahen Mahendran,et al.  EXPERIMENTAL STUDY OF UNLIPPED CHANNEL BEAMS SUBJECT TO WEB CRIPPLING UNDER ONE FLANGE LOAD CASES , 2019 .

[20]  Shanmuganathan Gunalan,et al.  Fastened Aluminum-Lipped Channel Sections Subjected to Web Crippling under Two-Flange Loading Conditions: Experimental Study , 2020 .

[21]  Poologanathan Keerthan,et al.  Web crippling behaviour and design of cold-formed steel sections , 2019, Thin-Walled Structures.

[22]  Dinar Camotim,et al.  Web crippling failure using quasi-static FE models , 2014 .

[23]  Ben Young,et al.  Design of aluminium alloy stocky hollow sections subjected to concentrated transverse loads , 2018 .

[24]  Shanmuganathan Gunalan,et al.  Shear design rules for roll-formed aluminium lipped channel beams , 2020 .

[25]  Amir M. Yousefi,et al.  Cold-formed ferritic stainless steel unlipped channels with web openings subjected to web crippling under interior-two-flange loading condition – Part II: Parametric study and design equations , 2017 .