Analysis of Effect of Machining Parameters During Electrical Discharge Machining Using Taguchi-Based Multi-Objective PSO

The present contribution describes an application of a hybrid approach using response surface methodology (RSM) and particle swarm optimization (PSO) for optimizing the machining parameters in elec...

[1]  Sameh Habib,et al.  Study of the parameters in electrical discharge machining through response surface methodology approach , 2009 .

[2]  C. L. Lin,et al.  Optimisation of the EDM Process Based on the Orthogonal Array with Fuzzy Logic and Grey Relational Analysis Method , 2002 .

[3]  Omkar Kulkarni,et al.  Particle Swarm Optimization Applications to Mechanical Engineering- A Review , 2015 .

[4]  A. Rajadurai,et al.  Effect of SiC and rotation of electrode on electric discharge machining of Al–SiC composite , 2002 .

[5]  Norliana Mohd Abbas,et al.  A review on current research trends in electrical discharge machining (EDM) , 2007 .

[6]  Baoping Cai,et al.  ELECTRIC DISCHARGE MILLING AND MECHANICAL GRINDING COMPOUND MACHINING OF SILICON CARBIDE CERAMIC , 2010 .

[7]  George P. Petropoulos,et al.  Modeling of surface finish in electro-discharge machining based upon statistical multi-parameter analysis , 2004 .

[8]  Baoping Cai,et al.  Machining Performance Optimization in End ED Milling and Mechanical Grinding Compound Process , 2012 .

[9]  Hao Yin,et al.  Accelerating particle swarm optimization using crisscross search , 2016, Inf. Sci..

[10]  Ko-Ta Chiang,et al.  Modeling and analysis of the effects of machining parameters on the performance characteristics in the EDM process of Al2O3+TiC mixed ceramic , 2008 .

[11]  Masanori Kunieda,et al.  Advancing EDM through fundamental insight into the process , 2005 .

[12]  Sanjeev Kumar,et al.  Study of Surface Properties in Particulate-Reinforced Metal Matrix Composites (MMCs) Using Powder-Mixed Electrical Discharge Machining (EDM) , 2014 .

[13]  C. Liu.  Microstructure and tool electrode erosion in EDMed of TiN/Si3N4 composites , 2003 .

[14]  G. Levy,et al.  EDM-Future Steps towards the Machining of Ceramics , 1988 .

[15]  P.Narender Singh,et al.  Optimization by Grey relational analysis of EDM parameters on machining Al–10%SiCP composites , 2004 .

[16]  L. Li,et al.  Electroforming of TiB2-Reinforced Copper Matrix Electrode for EDM , 2016 .

[17]  N. Selvakumar,et al.  Experimental Analysis of Al–TiC Sintered Nanocomposite on EDM Process Parameters Using ANOVA , 2016 .

[18]  Baoping Cai,et al.  Optimizing machining parameters of silicon carbide ceramics with ED milling and mechanical grinding combined process , 2010 .

[19]  H. Zarepour,et al.  Statistical analysis on electrode wear in EDM of tool steel DIN 1.2714 used in forging dies , 2007 .

[20]  Yang Liu,et al.  A self-adaptive harmony PSO search algorithm and its performance analysis , 2015, Expert Syst. Appl..

[21]  T. A. El-Taweel.  Multi-response optimization of EDM with Al–Cu–Si–TiC P/M composite electrode , 2009 .

[22]  K. Palanikumar,et al.  Optimization of electrical discharge machining characteristics of WC/Co composites using non-dominated sorting genetic algorithm (NSGA-II) , 2008 .

[23]  B. Singh,et al.  Influences of Process Parameters on MRR Improvement in Simple and Powder-Mixed EDM of AA6061/10%SiC Composite , 2015 .

[24]  K. Palanikumar,et al.  Influence of process parameters on electric discharge machining of WC/30%Co composites , 2008 .

[25]  C. J. Luis,et al.  Material removal rate and electrode wear study on the EDM of silicon carbide , 2005 .

[26]  Stephen T. Newman,et al.  State of the art electrical discharge machining (EDM) , 2003 .

[27]  R. K. Bhoi,et al.  Artificial Neural Network Prediction of Material Removal Rate in Electro Discharge Machining , 2005 .