Micro-electrode fabrication processes for micro-EDM drilling and milling: a state-of-the-art review

These days, miniaturized products have a lot of applications in biotechnology, information technology, environmental and medical industries, electric devices, miniaturized machines, and so on. Micro-electrical discharge machining (micro-EDM) is one the most efficient technologies among the nonconventional machining technologies for producing micro-components. Micro-EDM is able to machine tough die materials which cannot be machined by micro-milling. The micro-EDM method has the capability to machine electrical conductive materials with various hardness, strength, and temperature-resistant and complex shapes with accurate dimensions and fine surface roughness. Moreover, it is widely used to produce micro-scale components and structures such as micro-mold, micro-die, micro-probes, micro-tools, fuel nozzles, photo-masks, thin sheet materials, and complex 3D shapes with high accuracy. This paper presents a state-of-the-art review of micro-EDM process as well as the various kinds of micro-electrode and workpiece materials and dielectrics that have been used by previous researchers. In addition, this paper extensively describes and compares various micro-electrode and micro-tool fabrication processes in order to produce precise micro-products. This work is very helpful for the micro-EDM manufacturers and users to select suitable material, dielectric and fabrication processes in researches, and industry applications.

[1]  Yong Li,et al.  Micro electro discharge machine with an inchworm type of micro feed mechanism , 2002 .

[2]  M. Noordin,et al.  Development of new fabrication and measurement techniques of micro-electrodes with high aspect ratio for micro EDM using typical EDM machine , 2017 .

[3]  Hamid Baseri,et al.  Experimental study of rotary magnetic field-assisted dry EDM with ultrasonic vibration of workpiece , 2013 .

[4]  P. Withers,et al.  Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes , 2015 .

[5]  A. Senthil Kumar,et al.  A multiprocess machine tool for compound micromachining , 2010 .

[6]  Elman C Jameson,et al.  Electrical Discharge Machining , 2001 .

[7]  B. Yan,et al.  Influence of kerosene and distilled water as dielectrics on the electric discharge machining characteristics of Ti–6A1–4V , 1999 .

[8]  A. Sarhan,et al.  Investigating the electrical discharge machining (EDM) parameter effects on Al-Mg2Si metal matrix composite (MMC) for high material removal rate (MRR) and less EWR–RSM approach , 2015 .

[9]  Atanas Ivanov,et al.  Recent developments and research challenges in electrochemical micromachining (µECM) , 2013 .

[10]  Bijoy Bhattacharyya,et al.  Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti-6Al-4V alloy , 2010 .

[11]  Muhammad P. Jahan,et al.  Nanofinishing of hard materials using micro-electrodischarge machining , 2009 .

[12]  S. Melkote,et al.  Effect of plastic side flow on surface roughness in micro-turning process , 2006 .

[13]  Kai Egashira,et al.  Electrical discharge machining of submicron holes using ultrasmall-diameter electrodes , 2010 .

[14]  Gwo-Lianq Chern,et al.  Study on burr formation in micro-machining using micro-tools fabricated by micro-EDM , 2007 .

[15]  Kai Egashira,et al.  Ultrasonic Vibration Drilling of Microholes in Glass , 2002 .

[16]  Makoto Miyazaki,et al.  Electrical discharge machining with ultralow discharge energy , 2006 .

[17]  G. Maccarini,et al.  Process performance of micro-EDM drilling of stainless steel , 2014 .

[18]  M. Kunieda,et al.  Observation of relationship between bubbles and discharge locations in EDM using transparent electrodes , 2015 .

[19]  G. Chern,et al.  Punching of noncircular micro-holes and development of micro-forming , 2007 .

[20]  A. Senthil Kumar,et al.  Development of micropin fabrication process using tool based micromachining , 2006 .

[21]  M. Kunieda,et al.  Experimental attempts of sub-micrometer order size machining using micro-EDM , 2006 .

[22]  Naotake Mohri,et al.  Three-dimensional shaping by dot-matrix electrical discharge machining , 1997 .

[23]  I. Puertas,et al.  Analysis of the influence of EDM parameters on surface quality, MRR and EW of WC–Co , 2004 .

[24]  K. Wegener,et al.  A strategy for low electrode wear in meso–micro-EDM , 2015 .

[25]  K. Rajurkar,et al.  Investigation of the relationship between the white layer thickness and 3D surface texture parameters in the die sinking EDM process , 2005 .

[26]  J. Mathew,et al.  Effect of Powder Mixed Dielectric on Material Removal and Surface Modification in Microelectric Discharge Machining of Ti-6Al-4V , 2016 .

[27]  Mu-Tian Yan,et al.  A study on electrode wear sensing and compensation in Micro-EDM using machine vision system , 2009 .

[28]  Dominiek Reynaerts,et al.  Process capabilities of Micro-EDM and its applications , 2007 .

[29]  Shun-Tong Chen.  A high-efficiency approach for fabricating mass micro holes by batch micro EDM , 2007 .

[30]  Vidyut Dey,et al.  A review on the use of dielectric fluids and their effects in electrical discharge machining characteristics , 2015 .

[31]  J. Valentincic,et al.  Towards the effective tool wear control in micro-EDM milling , 2010 .

[32]  D. Sheu.  Microelectrode Tools Manufacturing by Hybrid Circuits Twin-Wire Electrodischarge Grinding , 2010 .

[33]  Masanori Kunieda,et al.  Reverse simulation of sinking EDM applicable to large curvatures , 2012 .

[34]  C. Chu,et al.  Fabrication of multiple electrodes by reverse EDM and their application in micro ECM , 2006 .

[35]  S. Mahapatra,et al.  A hybrid approach for multi-response optimization of non-conventional machining on AlSiCp MMC , 2013 .

[36]  Takeshi Yoneyama,et al.  Micro cutting in the micro lathe turning system , 1999 .

[37]  Chia-Lung Kuo,et al.  Fabrication of series-pattern micro-disk electrode and its application in machining micro-slit of less than 10 μm , 2004 .

[38]  Y. Wong,et al.  A comparative experimental investigation of deep-hole micro-EDM drilling capability for cemented carbide (WC-Co) against austenitic stainless steel (SUS 304) , 2010 .

[39]  Yong Li,et al.  Mechanism design and process control of micro EDM for drilling spray holes of diesel injector nozzles , 2013 .

[40]  M. Utlaut.  Focused ion beams for nano-machining and imaging , 2014 .

[41]  C. Tsao,et al.  A study of the machining characteristics of micro EDM milling and its improvement by electrode coating , 2015 .

[42]  Kuang-Yuan Kung,et al.  Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide , 2009 .

[43]  T. Senthilvelan,et al.  Application of response surface method on machining of Al–SiC nano-composites , 2013 .

[44]  Takahisa Masuzawa,et al.  Wire Electro-Discharge Grinding for Micro-Machining , 1985 .

[45]  Harshit K. Dave,et al.  Study on effect of process parameters on overcut and tool wear rate during micro-electro-discharge slotting process , 2016 .

[46]  Yong Li,et al.  Algorithms and machining experiments to reduce depth errors in servo scanning 3D micro EDM , 2014 .

[47]  Chen-Siang Hsu,et al.  Fabrication of micro-electrodes by multi-EDM grinding process , 2003 .

[48]  Masanori Kunieda,et al.  Advancing EDM through fundamental insight into the process , 2005 .

[49]  Florian Solzbacher,et al.  Fabrication of compliant high aspect ratio silicon microelectrode arrays using micro-wire electrical discharge machining , 2009 .

[50]  Muneer Khan Mohammed,et al.  A Hybrid Machining Process Combining Micro-EDM and Laser Beam Machining of Nickel–Titanium-Based Shape Memory Alloy , 2016 .

[51]  Takahisa Masuzawa,et al.  State of the Art of Micromachining , 2000 .

[52]  Mustafa Ay,et al.  Optimization of micro-EDM drilling of inconel 718 superalloy , 2013 .

[53]  Y. Wong,et al.  An experimental investigation into the micro-electrodischarge machining behavior of p-type silicon , 2011 .

[54]  Mahmudur Rahman,et al.  An experimental study on micro-EDM in low-resistivity deionized water using short voltage pulses , 2012 .

[55]  Yong Li,et al.  Precision machining of micro tool electrodes in micro EDM for drilling array micro holes , 2015 .

[56]  Y. Wong,et al.  A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator , 2009 .

[57]  C. C. Tsao,et al.  Evaluation of the characteristics of the microelectrical discharge machining process using response surface methodology based on the central composite design , 2012 .

[58]  Chong Nam Chu,et al.  Micro ECM with ultrasonic vibrations using a semi-cylindrical tool , 2009 .

[59]  Fritz Klocke,et al.  Technological and economical comparison of roughing strategies via milling, sinking-EDM, wire-EDM and ECM for titanium- and nickel-based blisks , 2013 .

[60]  Masanori Kunieda,et al.  Improvement of machining characteristics of micro-EDM using transistor type isopulse generator and servo feed control , 2004 .

[61]  Shun-Tong Chen.  Fabrication of high-density micro holes by upward batch micro EDM , 2008 .

[62]  Mahmudur Rahman,et al.  Tool-based micro-machining , 2007 .

[63]  M. Kunieda,et al.  Increasing discharge energy of micro-EDM with electrostatic induction feeding method through resonance in circuit , 2016 .

[64]  Hiroshi Takada,et al.  Micromachining with SR and FEL , 1998 .

[65]  Mahmudur Rahman,et al.  Profile error compensation in high precision 3D micro-EDM milling , 2013 .

[66]  W. D. Liu,et al.  Machining Characteristics of Al2O3/6061Al Composite using Rotary EDM with a Disklike Electrode , 2000 .

[67]  Masanori Kunieda,et al.  Study on decreasing tool wear in EDM due to arc spots sliding on electrodes , 2010 .

[68]  Ming-Guo Her,et al.  Study of the Batch Production of Micro Parts Using the EDM Process , 2002 .

[69]  Mahmudur Rahman,et al.  A study on the machining of high-aspect ratio micro-structures using micro-EDM , 2003 .

[70]  Mahmudur Rahman,et al.  A review on the conventional and micro-electrodischarge machining of tungsten carbide , 2011 .

[71]  Masanori Kunieda,et al.  Improvement of EDM efficiency of silicon single crystal through ohmic contact , 2000 .

[72]  Kai Egashira,et al.  Micro-drilling of monocrystalline silicon using a cutting tool , 2002 .

[73]  Naotake Mohri,et al.  A parallel link end effector for scanning electrical discharge machining process , 1998 .

[74]  K. Ehmann,et al.  High throughput microfabrication using laser induced plasma in saline aqueous medium , 2015 .

[75]  Kazuo Yamazaki,et al.  High efficiency fine boring of monocrystalline silicon ingot by electrical discharge machining , 1999 .

[76]  Yongfeng Guo,et al.  Electrical discharge precision machining parameters optimization investigation on S-03 special stainless steel , 2014 .

[77]  M. Kunieda,et al.  Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method , 2015 .

[78]  Wansheng Zhao,et al.  A CAD/CAM system for micro-ED-milling of small 3D freeform cavity , 2004 .

[79]  A. B. Puri,et al.  Simultaneous optimisation of multiple performance characteristics in micro-EDM drilling of titanium alloy , 2012 .

[80]  Y. Wong,et al.  An experimental investigation into the micro-electro-discharge machining behaviour of aluminium alloy (AA 2024) , 2015 .

[81]  Takayuki Tsujimoto,et al.  Study of vibration-assisted micro-EDM-The effect of vibration on machining time and stability of discharge , 2008 .

[82]  Hans Kurt Tönshoff,et al.  Three-Dimensional Micromachining by Machine Tools , 1997 .

[83]  Y. Qin,et al.  Micro-manufacturing: research, technology outcomes and development issues , 2010 .

[84]  E. Uhlmann,et al.  Influence of grain size on the wear behavior of CVD diamond coatings in micro-EDM , 2010 .

[85]  M. Kunieda,et al.  EDM of micro-rods by self-drilled holes , 2004 .

[86]  Harshit K. Dave,et al.  Studies on quality of microholes generated on Al 1100 using micro-electro-discharge machining process , 2015 .

[87]  Dong-Yea Sheu,et al.  Assembling ball-ended styli for CMM's tactile probing heads on micro EDM , 2013 .

[88]  Muhammad P. Jahan,et al.  On-machine fabrication of high-aspect-ratio micro-electrodes and application in vibration-assisted micro-electrodischarge drilling of tungsten carbide , 2010 .

[89]  Jianxin Deng,et al.  Surface textures on cemented carbide cutting tools by micro EDM assisted with high-frequency vibration , 2016 .

[90]  Stefan Simeonov Dimov,et al.  Development of surface roughness optimisation and prediction for the process of wire electro-discharge grinding , 2013 .

[91]  T. Masuzawa,et al.  An index to evaluate the wear resistance of the electrode in micro-EDM , 2004 .

[92]  A. Kumar,et al.  Micro milling of pure copper , 2001 .

[93]  Zuyuan Yu,et al.  Tool wear compensation in 3D micro EDM based on the scanned area , 2013 .

[94]  I. Puertas,et al.  Modelling of surface finish, electrode wear and material removal rate in electrical discharge machining of hard-to-machine alloys , 2015 .

[95]  Stephen T. Newman,et al.  State of the art electrical discharge machining (EDM) , 2003 .

[96]  Andreas Schubert,et al.  Analysis of the effect of vibrations on the micro-EDM process at the workpiece surface , 2011 .

[97]  M. Kunieda,et al.  Study of EDM cutting of single crystal silicon carbide , 2014 .

[98]  Y. S. Tarng,et al.  Monitoring of the electrical discharge machining process by abductive networks , 1997 .

[99]  T. Masuzawa,et al.  Micro-EDM for Three-Dimensional Cavities - Development of Uniform Wear Method - , 1998 .

[100]  Raymond Snoeys,et al.  Current Trends in Non-Conventional Material Removal Processes , 1986 .

[101]  Mu-Tian Yan,et al.  Process planning and electrode wear compensation for 3D micro-EDM , 2011 .

[102]  Masanori Komuro,et al.  Three-dimensional nanostructure fabrication by focused-ion-beam chemical vapor deposition , 2000 .

[103]  M. Park,et al.  Electrical discharge machining using a strip electrode , 2013 .

[104]  Y. Wong,et al.  A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials , 2009 .

[105]  C. Chu,et al.  Fabrication of a micro-hole array on metal foil by nanosecond pulsed laser beam machining using a cover plate , 2015 .

[106]  Y. Wong,et al.  Study on the nano-powder-mixed sinking and milling micro-EDM of WC-Co , 2011 .

[107]  Kenichi Takahata,et al.  High-aspect-ratio WC-Co microstructure produced by the combination of LIGA and micro-EDM , 2000 .

[108]  G. Maccarini,et al.  Influence of electrode material in micro-EDM drilling of stainless steel and tungsten carbide , 2016 .

[109]  Bijoy Bhattacharyya,et al.  Investigation of electro-discharge micro-machining of titanium super alloy , 2009 .

[110]  Kazunori Uchida,et al.  Fabricating microgrooves with varied cross-sections by electrodischarge machining , 2010 .

[111]  Jicheng Bai,et al.  Diameter control of microshafts in wire electrical discharge grinding , 2014 .

[112]  Jianjun Qin,et al.  Building an EDM process model by an instrumental variable approach based on two interactive Kalman filters , 2013 .

[113]  M. Kunieda,et al.  Molecular dynamics simulation of the material removal mechanism in micro-EDM , 2011 .

[114]  Liu Zhidong,et al.  Study of unidirectional conductivity on the electrical discharge machining of semiconductor crystals , 2013 .

[115]  A. Schoth,et al.  Micro wire EDM for high aspect ratio 3D microstructuring of ceramics and metals , 2005 .

[116]  U. Natarajan,et al.  Prediction of quality responses in micro-EDM process using an adaptive neuro-fuzzy inference system (ANFIS) model , 2013 .

[117]  Gianluca Danilo D'Urso,et al.  Workpiece and electrode influence on micro-EDM drilling performance , 2014 .

[118]  E. Uhlmann,et al.  Machining of micro/miniature dies and moulds by electrical discharge machining—Recent development , 2005 .

[119]  Sanjeev Kumar,et al.  EDM of Metal Matrix Composite for Parameter Design Using Lexicographic Goal Programming , 2013 .

[120]  B. Yan,et al.  Bending strength analysis of micro WC-shaft manufactured by micro electro-discharge machining , 2005 .

[121]  Kimiyuki Mitsui,et al.  Development of an integrated apparatus of micro-EDM and micro-CMM , 2013 .

[122]  Yusuf Keskin,et al.  An experimental study for determination of the effects of machining parameters on surface roughness in electrical discharge machining (EDM) , 2006 .

[123]  D. Sheu.  High-speed micro electrode tool fabrication by a twin-wire EDM system , 2008 .