Effect of compression ring elastodynamics behaviour upon blowby and power loss

The automotive industry is subject to increasing pressure to reduce the CO emissions and improve fuel efficiency in internal combustion engines. Improvements may be achieved in a number of ways. The parasitic losses throughout the engine cycle emanate from friction in all engine contact conjunctions in addition to pumping losses. In particular one main contributory conjunction is the piston ring pack assembly. At low engine speeds, the contribution of friction to the total losses within the engine is increased significantly compared with the thermodynamic losses. Additionally, the sealing capability of the ring is crucial in determining the power output of the engine with any loss of sealing contributing to power loss, as well as blowby. Most reported studies on compression ring-cylinder conjunction do not take into account complex ring in-plane and out-of-plane elastodynamics. Hitherto, there has not been a numerical methodology which integrates tribology of an elastic compression ring, subject to modal behaviour in a coupled solution. This paper discusses the inclusion of transient ring elastodynamics of the top compression ring, interacting with blowby effects within the ring pack. The ring dynamics methodology is briefly highlighted for both in-plane and out-of-plane motions. In addition, a one-dimensional gas flow model that captures blowby behaviour is included. A case study is presented, using measured engine data. Gas flow and frictional losses at various engine speeds are predicted. The effect of gas blowby on the ring's tribological response can be ascertained, as well as the ring's dynamic motion within its retaining groove. Copyright © 2014 SAE International.

[1]  Shoichi Furuhama,et al.  New Device for the Measurement of Piston Frictional Forces in Small Engines , 1983 .

[2]  Naeim A. Henein,et al.  A Model for Wear and Friction in Cylinder Liners and Piston Rings , 2006 .

[3]  Sanjay D. Gulwadi.  Analysis of Tribological Performance of a Piston Ring Pack , 2000 .

[4]  D. E. Richardson,et al.  Review of Power Cylinder Friction for Diesel Engines , 2000 .

[5]  S. Timoshenko,et al.  Theory Of Elasticity. 2nd Ed. , 1951 .

[6]  Shoichi Furuhama,et al.  A Dynamic Theory of Piston-Ring Lubrication : 3rd Report, Measurement of Oil Film Thickness , 1961 .

[7]  M. Takiguchi,et al.  Oil Film Thickness Measurement and Analysis of a Three Ring Pack in an Operating Diesel Engine , 2000 .

[8]  D. J. Picken,et al.  The ``limits of lubrication'' concept applied to thepiston ring zone lubrication of modern engines , 1997 .

[9]  John B. Heywood,et al.  Flow in the piston-cylinder-ring crevices of a spark-ignition engine: effect on hydrocarbon emissions, efficiency and power , 1982 .

[10]  S. Theodossiades,et al.  Influence of In-Plane Dynamics of Thin Compression Rings on Friction in Internal Combustion Engines , 2012 .

[11]  Homer Rahnejat,et al.  Analytical Evaluation of Fitted Piston Compression Ring: Modal Behaviour and Frictional Assessment , 2011 .

[12]  P. C. Mishra,et al.  Tribology of the ring—bore conjunction subject to a mixed regime of lubrication , 2009 .

[13]  M-T Ma,et al.  Analysis of lubrication and friction for a complete piston-ring pack with an improved oil availability model: Part 1: Circumferentially uniform film , 1997 .

[14]  Shoichi Furuhama,et al.  A Dynamic Theory of Piston-Ring Lubrication : 1st Report, Calculation , 1958 .

[15]  John B. Heywood,et al.  Modeling Piston-Ring Dynamics, Blowby, and Ring-Twist Effects , 1998 .

[16]  G. M. Hamilton,et al.  First Paper: Measurement of the Oil-Film Thickness between the Piston Rings and Liner of a Small Diesel Engine , 1974 .

[17]  J. Greenwood,et al.  The Contact of Two Nominally Flat Rough Surfaces , 1970 .

[18]  Horace Lamb,et al.  On the Flexure and the Vibrations of a Curved Bar , 1887 .

[19]  Dan Richardson,et al.  UNDERSTANDING THE FUNDAMENTALS OF PISTON RING AXIAL MOTION AND TWIST AND THE EFFECTS ON BLOW-BY , 2009 .

[20]  Ozgen Akalin,et al.  Piston Ring-Cylinder Bore Friction Modeling in Mixed Lubrication Regime: Part I—Analytical Results , 2001 .

[21]  C. M. Taylor,et al.  Automobile Engine Tribology - Approaching the Surface , 2000 .

[22]  Clive L. Dym,et al.  On the vibration of thin circular rings , 1980 .

[23]  Owen Saunders,et al.  Oil Film Temperature and Thickness Measurements on the Piston Rings of a Diesel Engine , 1972 .

[24]  Homer Rahnejat,et al.  Friction Under Transient Mixed Regime of Lubrication in Conjunction of an Elastic Ring Within a Real Cylinder , 2012 .

[25]  J. Mayer,et al.  Piston Ring Lubrication and Cylinder Bore Wear Analysis, Part I—Theory , 1974 .

[26]  H. Rahnejat,et al.  Tribology of compression ring-to-cylinder contact at reversal , 2008 .

[27]  C. M. Taylor,et al.  Automobile engine tribology—design considerations for efficiency and durability , 1998 .

[28]  Simon C. Tung,et al.  Automotive tribology overview of current advances and challenges for the future , 2004 .

[29]  Shoichi Furuhama.  A Dynamic Theory of Piston-Ring Lubrication : 2nd Report, Experiment , 1959 .

[30]  Homer Rahnejat,et al.  Thermoelastohydrodynamics of a rough piston compression ring-to-cylinder bore conjunction , 2011 .

[31]  Robert R. Archer.  Small vibrations of thin incomplete circular rings , 1960 .

[32]  Fred H. Brown.  Lateral vibration of ring-shaped frames , 1934 .

[33]  I. U Ojalvo.  Coupled twist-bending vibrations of incomplete elastic rings , 1962 .

[34]  Duncan Dowson,et al.  A Theoretical Analysis of the Twin-Land Type of Oil-Control Piston Ring: , 1981 .