Digital reproduction of historical building ornamental components: From 3D scanning to 3D printing

[1]  Nathalie Labonnote,et al.  Additive construction: State-of-the-art, challenges and opportunities , 2016 .

[2]  Xiangyu Wang,et al.  A critical review of the use of 3-D printing in the construction industry , 2016 .

[3]  Danijel Rebolj,et al.  Interoperability requirements for automated manufacturing systems in construction , 2016, J. Intell. Manuf..

[4]  Junqing Yu,et al.  Dense 3D reconstruction combining depth and RGB information , 2016, Neurocomputing.

[5]  Rongrong Ji,et al.  On-Device Mobile Landmark Recognition Using Binarized Descriptor with Multifeature Fusion , 2015, ACM Trans. Intell. Syst. Technol..

[6]  Yan Zhang,et al.  Inertial sensors supported visual descriptors encoding and geometric verification for mobile visual location recognition applications , 2015, Signal Process..

[7]  Benchang Wei,et al.  Wide area localization and tracking on camera phones for mobile augmented reality systems , 2015, Multimedia Systems.

[8]  Xiangyu Wang,et al.  Applicability of 4D modeling for resource allocation in mega liquefied natural gas plant construction , 2015 .

[9]  Martin Skitmore,et al.  Three-dimensional printing in the construction industry: A review , 2015 .

[10]  C. Moses,et al.  Methods for measuring rock surface weathering and erosion: A critical review , 2014 .

[11]  Fabio Gramazio,et al.  Authoring Robotic Processes , 2014 .

[12]  David García,et al.  Textile-Reinforced Mortar as Strengthening Material for Masonry Arches , 2014 .

[13]  E. Gambao,et al.  Extending automation of building construction — Survey on potential sensor technologies and robotic applications , 2013 .

[14]  Changmin Kim,et al.  Skeleton-based 3D reconstruction of as-built pipelines from laser-scan data , 2013 .

[15]  Asterios Bakolas,et al.  Non-destructive techniques as a tool for the protection of built cultural heritage , 2013 .

[16]  Galina Bogdanova,et al.  Digitization and 3D Scanning of Historical Artifacts , 2013, Digital Presentation and Preservation of Cultural and Scientific Heritage.

[17]  Lieyun Ding,et al.  Application of 4D visualization technology for safety management in metro construction , 2013 .

[18]  David Smith,et al.  Printed buildings: an international race for the ultimate in automation , 2012 .

[19]  Y. M. Ibrahim,et al.  Review of Photographic/Imaging Applications in Construction , 2011 .

[20]  A. Pasko,et al.  Digitally Interpreting Traditional Folk Crafts , 2011, IEEE Computer Graphics and Applications.

[21]  Paulo B. Lourenço,et al.  Geometric issues and ultimate load capacity of masonry arch bridges from the northwest Iberian Peninsula , 2010 .

[22]  Diego González-Aguilera,et al.  Terrestrial laser scanning intensity data applied to damage detection for historical buildings , 2010 .

[23]  W. Verstraete,et al.  Microbial carbonate precipitation in construction materials: A review , 2010 .

[24]  Melvin J. Wachowiak,et al.  3d Scanning and Replication for Museum and Cultural Heritage Applications , 2009 .

[25]  S. Siegesmund,et al.  Monument futures: climate change, air pollution, decay and conservation—the Wolf-Dieter Grimm-volume , 2008 .

[26]  D. Arnold.  Pasteur's quadrant: cultural heritage as inspiration for basic research in computer science , 2008 .

[27]  O. Salvadori,et al.  Ecological analysis and biodeterioration processes over time at the Hieroglyphic Stairway in the Copàn (Honduras) archaeological site , 2005 .

[28]  Roberto Scopigno,et al.  Digital representation and multimodal presentation of archeological graffiti at Pompei , 2004, VAST.

[29]  Paulo B. Lourenço,et al.  Computations on historic masonry structures , 2002 .

[30]  Alonzo C. Addison,et al.  Emerging Trends in Virtual Heritage , 2000, IEEE Multim..

[31]  Jiang Yu Zheng,et al.  Virtual Recovery of Excavated Relics , 1999, IEEE Computer Graphics and Applications.

[32]  Eric Doehne,et al.  Stone Conservation: An Overview of Current Research , 1998 .

[33]  Joseph Pegna,et al.  Exploratory investigation of solid freeform construction , 1997 .

[34]  Ismail Al-Rawi,et al.  Implementation of an Efficient Scan-Line Polygon Fill Algorithm , 2014 .

[35]  Michael Groenendyk,et al.  A Further Investigation into 3D Printing and 3D Scanning at the Dalhousie University Libraries: a Year Long Case Study , 2013 .

[36]  Richard A. Buswell,et al.  Developments in construction-scale additive manufacturing processes , 2012 .

[37]  Richard A. Buswell,et al.  Development of a viable concrete printing process , 2011 .

[38]  H. Siedel,et al.  SALT LOAD AND DETERIORATION OF SANDSTONE AT THE TEMPLE OF ANGKOR WAT, CAMBODIA , 2008 .

[39]  L. Lazzarini,et al.  The deterioration of Euganean trachyte in Venice. , 2008 .

[40]  Peter Brimblecombe,et al.  Damage to Buildings from Future Climate and Pollution , 2007 .

[41]  R. Sawatzky,et al.  Use of Hand-held Laser Scanning and 3D Printing for Creation of a Museum Exhibit. , 2005 .