Toughening of Layered Ceramic Composites with Residual Surface Compression

Effects of macroscopic residual stresses on fracture toughness of multilayered ceramic laminates were studied analytically and experimentally. Stress intensities for edge cracks in three-layer, single-edge-notch-bend (SENB) specimens with stepwise varying residual stresses in the absence of the crack and superimposed bending were calculated as a function of the crack length by the method of weight function. The selected weight function and the method of calculation were validated by calculating stress intensities for edge cracks in SENB specimens without the residual stresses and obtaining agreement with the stress-intensity equation recommended in ASTM Standard E-399. The stress-intensity calculations for the three-layer laminates with the macroscopic residual stresses were used to define an apparent fracture toughness. The theoretical predictions of the apparent fracture toughness were verified by experiments on three-layer SENB specimens of polycrystalline alumina with 15 vol% of unstabilized zirconia dispersed in the outer layers and 15 vol% of fully stabilized zirconia dispersed in the inner layer. A residual compression of ∼400 MPa developed in the outer layers by the constrained transformation of the unstabilized zirconia from the tetragonal to the monoclinic phase enhanced the apparent fracture toughness to values of 30 MPa.m1/2 in a system where the intrinsic fracture toughness was only 5 to 7 MPa.m1/2.

[1]  A. Virkar,et al.  Measurement of Residual Stresses in Oxide–ZrO2 Three‐Layer Composites , 1988 .

[2]  M. R. James,et al.  Factors Influencing Residual Surface Stresses due to a Stress‐Induced Phase Bansformation , 1983 .

[3]  D. Shetty,et al.  Strength Improvement in Transformation‐Toughened Alumina by Selective Phase Transformation , 1987 .

[4]  A. Virkar,et al.  Indentation Fracture Response and Damage Resistance of Al2O3‐ZrO2 Composites Strengthened by Transformation‐Induced Residual Stresses , 1988 .

[5]  A. Varshneya.  Stresses in Glass-to-Metal Seals , 1982 .

[6]  R. Steinbrech.  Toughening mechanisms for ceramic materials , 1992 .

[7]  David J. Green,et al.  Compressive Surface Strengthening of Brittle Materials by a Residual Stress Distribution , 1983 .

[8]  D. J. Green.  A Technique for Introducing Surface Compression into Zirconia Ceramics , 1983 .

[9]  J. Rice,et al.  Some remarks on elastic crack-tip stress fields , 1972 .

[10]  Jorgen Selsing,et al.  Internal Stresses in Ceramics , 1961 .

[11]  R. Lakshminarayanan,et al.  Rolling-Contact Fatigue and Wear of CVD-Sic with Residual Surface Compression , 1995 .

[12]  I. W. Donald.  Methods for improving the mechanical properties of oxide glasses , 1989 .

[13]  Jow-Lay Huang,et al.  Strengthening of Oxide Ceramics by Transformation‐Induced Stress , 1987 .

[14]  J. Srawley.  Wide range stress intensity factor expressions for ASTM E 399 standard fracture toughness specimens , 1976, International Journal of Fracture.

[15]  V. Fréchette,et al.  Stress Distribution in Multiphase Systems: I, Composites with Planar Interfaces , 1967 .

[16]  D. Munz,et al.  Determination of Fracture Toughness at High Temperatures after Subcritical Crack Extension , 1992 .

[17]  A. Virkar,et al.  The effect of binder thickness and residual stresses on the fracture toughness of cemented carbides , 1985 .

[18]  D. J. Green,et al.  Crack Stability and T‐Curves Due to Macroscopic Residual Compressive Stress Profiles , 1991 .

[19]  D. Munz,et al.  Influence of crack-surface interactions on stress intensity factor in ceramics , 1990 .