Conceptualization and Multiobjective Optimization of the Electric System of an Airborne Wind Turbine

Airborne wind turbines (AWTs) represent a radically new and fascinating concept for future harnessing of wind power. This concept consists of realizing only the blades of a conventional wind turbine (CWT) in the form of a power kite flying at high speed perpendicular to the wind. On the kite are mounted a turbine, an electrical generator, and a power electronics converter. The electric power generated is transmitted via a medium voltage cable to the ground. Because of the high flight speed of the power kite, several times the actual wind speed, only a very small swept area of the turbine is required according to Betz's Law and/or a turbine of low weight for the generation of a given electric power. Moreover, because of the high turbine rotational speed, no gear transmission is necessary and the size of the generator is also reduced. For takeoff and landing of the power kite, the turbines act as propellers and the generators as motors, i.e., electric power is supplied so that the system can be maneuvered like a helicopter. In the present work, the configuration of power electronics converters for the implementation of a 100 kW AWT is considered. The major aspect here is the trade-off between power-to-weight ratio (W/kg) and efficiency. The dependence of cable weight and cable losses on the voltage level of power transmission is investigated, and a comparison is made between low voltage (LV) and medium voltage (MV) versions of generators. Furthermore, the interdependence of the weight and efficiency of a bidirectional dual active bridge dc-dc converter for coupling the rectified output voltage of a LV generator to the MV cable is discussed. On the basis of this discussion, the concept offering the best possible compromise of weight and efficiency in the power electronics system is selected and a model of the control behavior is derived for both the power flow directions. A control structure is then proposed and dimensioned. Furthermore, questions of electromagnetic compatibility and electrical safety are treated. In conclusion, the essential results of this paper are summarized, and an outlook on future research is given. To enable the reader to make simplified calculations and a comparison of a CWT with an AWT, the aerodynamic fundamentals of both the systems are summarized in highly simplified form in an Appendix, and numerical values are given for the 100 kW system discussed in this paper.

[1]  Florian Krismer,et al.  Modeling and optimization of bidirectional dual active bridge DC-DC converter topologies , 2010 .

[2]  Dushan Boroyevich,et al.  Future electronic power distribution systems a contemplative view , 2010, 2010 12th International Conference on Optimization of Electrical and Electronic Equipment.

[3]  Stephan Michael Neuhold.  A hyper elastic conductor for bulk energy transfer in the wall of spoolable tubes for electric deep drilling , 2007 .

[4]  J. Kolar,et al.  Theoretical Converter Power Density Limits for Forced Convection Cooling , 2005 .

[5]  Mahmood R. Azimi-Sadjadi,et al.  Isolation of resonance in acoustic backscatter from elastic targets using adaptive estimation schemes , 1995, IEEE Journal of Oceanic Engineering.

[6]  Johann W. Kolar,et al.  Accurate Power Loss Model Derivation of a High-Current Dual Active Bridge Converter for an Automotive Application , 2010, IEEE Transactions on Industrial Electronics.

[7]  C. Gomez-García,et al.  Design of a 3.5 meters rotor two bladed Horizontal Axis Wind Turbine , 2010, CONIELECOMP.

[8]  Moritz Diehl,et al.  Windenergienutzung mit schnell fliegenden Flugdrachen: eine Herausforderung für die Optimierung und RegelungWind Power via Fast Flying Kites: a Challenge for Optimization and Control , 2009, Autom..

[9]  T. Friedli,et al.  A Semiconductor Area Based Assessment of AC Motor Drive Converter Topologies , 2009, 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition.

[10]  Johann W. Kolar,et al.  Efficiency-Optimized High-Current Dual Active Bridge Converter for Automotive Applications , 2012, IEEE Transactions on Industrial Electronics.

[11]  Johann W. Kolar,et al.  Comparison of the chip area usage of 2-level and 3-level voltage source converter topologies , 2010, IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society.

[12]  Y. Perriard,et al.  Optimization of electric motor for a solar airplane application , 2005, IEEE Transactions on Industry Applications.

[13]  J. Biela,et al.  Exploring the pareto front of multi-objective single-phase PFC rectifier design optimization - 99.2% efficiency vs. 7kW/din3 power density , 2009, 2009 IEEE 6th International Power Electronics and Motion Control Conference.

[14]  P. Viarouge,et al.  Synthesis of high performance PM motors with concentrated windings , 1999, IEEE International Electric Machines and Drives Conference. IEMDC'99. Proceedings (Cat. No.99EX272).

[15]  Moritz Diehl,et al.  Optimal control for power generating kites , 2007, 2007 European Control Conference (ECC).

[16]  S. M. Neuhold,et al.  Hyperelastic High Voltage Conductor for Electric Drilling , 2005 .

[17]  B. Lansdorp,et al.  The Laddermill: work in progress , 2004 .

[18]  S. Waffler,et al.  Performance trends and limitations of power electronic systems , 2010, 2010 6th International Conference on Integrated Power Electronics Systems.

[19]  Johann W. Kolar,et al.  Comprehensive comparison of three-phase AC-AC Matrix Converter and Voltage DC-Link Back-to-Back Converter systems , 2010, The 2010 International Power Electronics Conference - ECCE ASIA -.

[20]  F. W. Lanchester,et al.  A CONTRIBUTION TO THE THEORY OF PROPULSION AND THE SCREW PROPELLER , 2009 .

[21]  J. P. Brown,et al.  Toward an improved understanding of thruster dynamics for underwater vehicles , 1995, IEEE Journal of Oceanic Engineering.

[22]  D.M. Divan,et al.  Performance characterization of a high power dual active bridge DC/DC converter , 1990, Conference Record of the 1990 IEEE Industry Applications Society Annual Meeting.

[23]  J. Kolar,et al.  Closed Form Solution for Minimum Conduction Loss Modulation of DAB Converters , 2012, IEEE Transactions on Power Electronics.

[24]  L. Fagiano,et al.  High-Altitude Wind Power Generation , 2010, IEEE Transactions on Energy Conversion.

[25]  Jian Sun,et al.  Small-Signal Methods for AC Distributed Power Systems–A Review , 2009, IEEE Transactions on Power Electronics.

[26]  M. L. Loyd,et al.  Crosswind kite power (for large-scale wind power production) , 1980 .

[27]  J. W. Kolar,et al.  Design of a minimum weight dual active bridge converter for an Airborne Wind Turbine system , 2012, 2012 Twenty-Seventh Annual IEEE Applied Power Electronics Conference and Exposition (APEC).