A Brief Review on injection moulding manufacturing process

Abstract The term quality has become a “catch all” term used in describing the various characteristics of an object. It is nearly impossible to define the term consistency. The quality is any particular or specific characteristics of a product development design object that contains or relates information about the object. This is primarily a chunk of geometry distinguished by its ability to perform a function with one or more other. In this primary processing conditions are studied from concept development to manufacturing of the product. Effect of different factors studied on the basis of processing parameters. Since quality and productivity are the two important contradictory objectives in any machining process. Some extent of quality has to be compromised while assurance giving for high productivity. Similarly productivity will be decreased while the efforts are channelized to enhance quality. To ensure high quality and productivity, it is necessary to optimize machining parameters. Various responses of quality of injection moulding process has been studied on the basis of performance parameters and methods. This paper aims to present plastic injection moulding process conditions. The processing conditions satisfied quality based product manufacturing.

[1]  Guoqun Zhao,et al.  Research on the reduction of sink mark and warpage of the molded part in rapid heat cycle molding process , 2013 .

[2]  B. Berginc,et al.  The use of the Taguchi approach to determine the influence of injection-moulding parameters on the properties of green parts , 2006 .

[3]  Lin Hua,et al.  Back Propagation neural network modeling for warpage prediction and optimization of plastic products during injection molding , 2011 .

[4]  Yvon Jarny,et al.  Optimal cooling design in injection moulding process – A new approach based on morphological surfaces , 2013 .

[5]  D. E. Dimla,et al.  Design and optimisation of conformal cooling channels in injection moulding tools , 2005 .

[6]  Babur Ozcelik,et al.  Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding , 2010 .

[7]  N. Ismail,et al.  The use of Taguchi method in the design of plastic injection mould for reducing warpage , 2007 .

[8]  Ming-Shyan Huang,et al.  Warpage control of thin-walled injection molding using local mold temperatures ☆ , 2015 .

[9]  F. Erzincanli,et al.  Prediction of minimum surface roughness in end milling mold parts using neural network and genetic algorithm , 2006 .

[10]  Nikos G. Pantelelis,et al.  Computational tools for the optimal design of the injection moulding process , 2002 .

[11]  Hongsheng Li,et al.  Reducing the effects of weldlines on appearance of plastic products by Taguchi experimental method , 2007 .

[12]  Mohan Kumar Pradhan,et al.  A Review of the Effect of Process Parameters on the Performance of Plastic Injection Molding Process to Control the Warpage in Plastics , 2015 .

[13]  S. Kamaruddin,et al.  Practical Applications of Taguchi Method for Optimization of Processing Parameters for Plastic Injection Moulding: A Retrospective Review , 2013 .

[14]  Pero Raos,et al.  Influence of Injection Moulding Parameters on Tensile Strength of Injection Moulded Part , 2014, MIE 2014.

[15]  Kuo-Ming Tsai,et al.  A study of the effects of process parameters for injection molding on surface quality of optical lenses , 2009 .

[16]  Karthik Ramani,et al.  A study of localized shrinkage in injection molding with high thermal conductivity molds , 2002 .

[17]  Dan Tursi,et al.  Process and tooling factors affecting sink marks for amorphous and crystalline resins , 2000 .

[18]  Shih-Jung Liu,et al.  The manufacturing of thermoplastic composite parts by water-assisted injection-molding technology , 2004 .

[19]  Gerald Berger,et al.  Novel approach to the measurement of the visual perceptibility of sink marks on injection molding parts , 2011 .

[20]  Gerald Berger,et al.  Measurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing model , 2014 .

[21]  Changyu Shen,et al.  Investigation of the Effect of Molding Variables on Sink Marks of Plastic Injection Molded Parts Using Taguchi DOE Technique , 2007 .

[22]  Jung‐il Song,et al.  Optimization of plastic injection molding process parameters for manufacturing a brake booster valve body , 2014 .

[23]  Guoqun Zhao,et al.  Optimal design of heating channels for rapid heating cycle injection mold based on response surface and genetic algorithm , 2009 .

[24]  Janez Marko Slabe,et al.  The impact of process parameters on test specimen deviations and their correlation with AE signals captured during the injection moulding cycle , 2013 .

[25]  Hans Nørgaard Hansen,et al.  Effects of holding pressure and process temperatures on the mechanical properties of moulded metallic parts , 2013 .

[26]  S. Hashemi,et al.  Effect of temperature on tensile properties of injection moulded short glass fibre and glass bead filled ABS hybrids , 2008 .

[27]  Babur Ozcelik,et al.  Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm , 2006 .

[28]  M. G. Rathi,et al.  Analysis Of Injection Moulding Process Parameters , 2012 .

[29]  Dipayan Das,et al.  Optimization of micro-injection molding process with respect to tensile properties of polypropylene , 2012 .

[30]  Jaiprakash Bhamniya,et al.  Optimization of Injection Moulding Process using Taguchi and ANOVA , 2013 .

[31]  Zahid A. Khan,et al.  Application of Taguchi Method in the Optimization of Injection Moulding Parameters for Manufacturing Products from Plastic Blend , 2010 .

[32]  Wu-Lin Chen,et al.  Finding efficient frontier of process parameters for plastic injection molding , 2013 .

[33]  R Spina,et al.  OPTIMIZATION OF INJECTION MOLDED PARTS BY USING ANN-PSO APPROACH , 2006 .

[34]  Babur Ozcelik,et al.  Minimization of warpage and sink index in injection-molded thermoplastic parts using Taguchi optimization method , 2006 .

[35]  Mohsen Esfahanian,et al.  Effect of reprocessing on shrinkage and mechanical properties of ABS and investigating the proper blend of virgin and recycled ABS in injection molding , 2014 .

[36]  I.H. Sahputra,et al.  Comparison of two flow analysis software for injection moulding tool design , 2007, 2007 IEEE International Conference on Industrial Engineering and Engineering Management.

[37]  Rickey Dubay,et al.  A principal component analysis model-based predictive controller for controlling part warpage in plastic injection molding , 2015, Expert Syst. Appl..

[38]  Cheng-Hung Huang,et al.  Optimization of Injection Molding Process for Tensile and Wear Properties of Polypropylene Components via Taguchi and Design of Experiments Method , 2007 .

[39]  Luigi Maria Galantucci,et al.  Evaluation of filling conditions of injection moulding by integrating numerical simulations and experimental tests , 2003 .

[40]  Abdul Halim Abdullah,et al.  Computer Simulation Opportunity In Plastic Injection Mold Development for Automotive Part , 2009, 2009 International Conference on Computer Technology and Development.

[41]  Li Jianyun,et al.  Optimization of plastics injection molding processing parameters based on the minimization of sink marks , 2010, 2010 International Conference on Mechanic Automation and Control Engineering.

[42]  Ming-Shyan Huang,et al.  Cavity pressure based grey prediction of the filling-to-packing switchover point for injection molding , 2007 .

[43]  D Mathivanan,et al.  Minimization of sink mark defects in injection molding process - Taguchi approach , 2010 .

[44]  C. K. Kwong,et al.  Application of artificial neural network and fuzzy logic in a case-based system for initial process parameter setting of injection molding , 2002, J. Intell. Manuf..

[45]  A. Behravesh,et al.  An experimental investigation on dimensional stability of injected wax patterns of gas turbine blades , 2007 .

[46]  Chih-Hung Tsai,et al.  Simulation and experimental study in determining injection molding process parameters for thin-shell plastic parts via design of experiments analysis , 2009, Expert Syst. Appl..

[47]  L. Hua,et al.  A hybrid of back propagation neural network and genetic algorithm for optimization of injection molding process parameters , 2011 .

[48]  Xuan-Phuong Dang,et al.  General frameworks for optimization of plastic injection molding process parameters , 2014, Simul. Model. Pract. Theory.

[49]  Alireza Akbarzadeh,et al.  Parameter Study in Plastic Injection Molding Process using Statistical Methods and IWO Algorithm , 2011 .