Effect of microstructure on abrasive wear behavior of thermally sprayed WC–10Co–4Cr coatings

Abstract Thermally sprayed WC–Co coatings have been widely used in the coatings industry for its superior sliding, abrasive and erosive wear properties. In applications where corrosion resistance is also required in addition to wear resistance, WC–10Co–4Cr is the preferred coating composition. The coatings produced by different thermal spray processes exhibit a broad range of coating hardness, porosity and microstructural features like grain size and volume fraction of individual phases. In this study, we have evaluated the coating microstructures of various WC–10Co–4Cr coatings produced from different spraying processes, such as high velocity oxy-fuel (HVOF) and pulsed combustion. The objective of our study is to explore the abrasive wear mechanism of WC–10Co–4Cr coatings in great detail, and determine how these mechanisms are influenced by the coating microstructure. Dry sand rubber wheel abrasion test rig (based on ASTM G65) is used for evaluating the three-body abrasive wear properties of the coatings, using alumina as the abrasive material. The coating microstructural parameters including WC grain size, volume fraction, binder mean free path have been quantitatively measured, and correlation between abrasive wear behavior of coatings and its microstructural parameters is sought. This study shows that binder mean free path of carbides (which is a function of WC grain size and volume fraction) is a very important parameter affecting the abrasion resistance of good quality coatings (containing low porosity). The lower the binder mean free path, the higher is the abrasive wear resistance offered by the coating. This is because the abrasive wear mechanism of these coatings is dominated by preferential removal of the binder phase, followed by pullout of WC grains.

[1]  S. Wayne,et al.  Structure/property relationships in sintered and thermally sprayed WC-Co , 1992 .

[2]  P. H. Shipway,et al.  Sliding wear behaviour of conventional and nanostructured HVOF sprayed WC–Co coatings , 2005 .

[3]  C. Moreau,et al.  Evaluation of four high velocity thermal spray guns using WC-10% Co-4% Cr cermets , 2002 .

[4]  Lidong Zhao,et al.  Influence of spray parameters on the particle in-flight properties and the properties of HVOF coating of WC-CoCr , 2004 .

[5]  Ian M. Hutchings,et al.  Results from an interlaboratory exercise to validate the micro-scale abrasion test , 2005 .

[6]  J. E. Nerz,et al.  Microstructural evaluation of tungsten carbide-cobalt coatings , 1992 .

[7]  J. Gurland,et al.  Hardness and deformation of cemented tungsten carbide , 1978 .

[8]  P. H. Shipway,et al.  Influence of heat treatment on the abrasive wear behaviour of HVOF sprayed WC–Co coatings , 1998 .

[9]  Christian Coddet,et al.  Influence of coating microstructure on the abrasive wear resistance of WC/Co cermet coatings , 2000 .

[10]  Qiaoqin Yang,et al.  Effect of carbide grain size on microstructure and sliding wear behavior of HVOF-sprayed WC–12% Co coatings , 2003 .

[11]  T. Fischer,et al.  The effects of fuel chemistry and feedstock powder structure on the mechanical and tribological properties of HVOF thermal-sprayed WC–Co coatings with very fine structures , 2003 .

[12]  Jiajun Liu,et al.  Micro-scale abrasive wear behaviour of HVOF sprayed and laser-remelted conventional and nanostructured WC-Co coatings , 2005 .

[13]  V. Cannillo,et al.  Mechanical and tribological properties of electrolytic hard chrome and HVOF-sprayed coatings , 2006 .

[14]  J. G. Baldoni,et al.  Abrasion and erosion of WC-Co with controlled microstructures , 1990 .

[15]  M. Gee,et al.  Rotating wheel abrasion of WC/Co hardmetals , 2005 .

[16]  P. Shipway,et al.  Dependence of microscale abrasion mechanisms of WC-Co hardmetals on abrasive type , 2005 .

[17]  J. Guilemany,et al.  Role of three-body abrasion wear in the sliding wear behaviour of WC–Co coatings obtained by thermal spraying , 2001 .

[18]  J. Schoenung,et al.  A review on nanostructured WC–Co coatings , 2002 .

[19]  P. H. Shipway,et al.  Abrasive wear behaviour of conventional and nanocomposite HVOF-sprayed WC–Co coatings , 1999 .

[20]  I. Hussainova,et al.  Solid particle erosion of thermal sprayed coatings , 2005 .

[21]  P. H. Shipway,et al.  Microstructural evolution in thermally sprayed WC-Co coatings: Comparison between nanocomposite and conventional starting powders , 2000 .

[22]  J. Martín,et al.  A study of high velocity oxy-fuel thermally sprayed tungsten carbide based coatings. Part 1: Microstructures , 1998 .

[23]  V. Cannillo,et al.  Wear behaviour of thermally sprayed ceramic oxide coatings , 2006 .

[24]  A. C. Bozzi,et al.  Wear resistance and wear mechanisms of WC–12%Co thermal sprayed coatings in three-body abrasion , 1999 .

[25]  S. Dong,et al.  Sliding wear behavior of the supersonic plasma sprayed WC-Co coating in oil containing sand , 2008 .

[26]  L. Ajdelsztajn,et al.  WC-based composite coatings prepared by the pulsed gas dynamic spraying process: Effect of the feedstock powders , 2008 .