Experimental study of the effect of microtexturing on oil lubricated ceramic/steel friction pairs

Abstract The objective of the research work was to study the potential of commercial ceramics such as Al 2 O 3 , Al 2 O 3 –ZrO 2 and SiC in pairing with steel 100Cr6 and laser-assisted deterministic microtexturing of the flat functional surfaces as design element for fast running friction systems, such as multiple disc clutches, under unidirectional oil lubricated sliding. A more fundamental part of the study was oriented towards understanding of the effect of microtexturing on mechanisms at mixed or boundary lubrication and development of lubricating oil film in the contact area. Experiments were carried out with pellet/disc geometry at relatively low velocities ≤0.3 m/s and normal loads ≤10 N using a model test with an attached microscope for in situ observation of the contact area. In the second part, friction behaviour of the different ceramic materials with and without microtexturing was characterised using a friction test rig at sliding velocities up to 10 m/s and normal loads ≤60 N under more practical-oriented conditions. Results showed that frictional behaviour was significantly influenced by the ceramic material and features of microtexturing, e.g. dimples, channels, width, depth and area coverage fraction. Improved understanding of operating mechanisms and design rules of microtexturing for controlling friction coefficient at practical sliding systems was obtained from a descriptive model.

[1]  K. Gahr,et al.  Friction control by surface engineering of ceramic sliding pairs in water , 2007 .

[2]  S. Schreck,et al.  Laser-assisted structuring of ceramic and steel surfaces for improving tribological properties , 2005 .

[3]  P. Blau,et al.  Investigation of the scuffing characteristics of candidate materials for heavy duty diesel fuel injectors , 2005 .

[4]  M. Scholle.  Hydrodynamical modelling of lubricant friction between rough surfaces , 2007 .

[5]  Izhak Etsion,et al.  Friction-Reducing Surface-Texturing in Reciprocating Automotive Components , 2001 .

[6]  Pär Nyman,et al.  Influence of surface topography on friction characteristics in wet clutch applications , 2006 .

[7]  Edward P. Becker,et al.  Trends in tribological materials and engine technology , 2004 .

[8]  I. Křupka,et al.  Experimental Study of Microtextured Surfaces Operating Under Thin-Film EHD Lubrication Conditions , 2007 .

[9]  K. Zum Gahr,et al.  Influence of surface finish and speed on reciprocating sliding wear of laser modified oxide ceramics in aqueous media , 2005 .

[10]  Ian M. Hutchings,et al.  Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions , 2007 .

[11]  Koshi Adachi,et al.  The Lubrication Effect of Micro-Pits on Parallel Sliding Faces of SiC in Water , 2002 .

[12]  D. Hwang,et al.  Tribological behaviour of steel‐alumina sliding pairs under boundary lubrication conditions , 2003 .

[13]  Yoshiteru Yasuda,et al.  Effect of surface texturing on friction reduction between ceramic and steel materials under lubricated sliding contact , 2003 .

[14]  Przemyslaw Zagrodzki,et al.  Generation of hot spots in a wet multidisk clutch during short-term engagement , 2003 .

[15]  Peter Andersson,et al.  Microlubrication effect by laser-textured steel surfaces , 2007 .

[16]  A. Gosman,et al.  Entrainment and Inlet Suction: Two Mechanisms of Hydrodynamic Lubrication in Textured Bearings , 2007 .

[17]  Antonius Lubrecht,et al.  Transient increase of film thickness in micro-textured EHL contacts , 2005 .

[18]  I. Etsion.  State of the art in Laser Surface Texturing , 2004 .

[19]  Izhak Etsion,et al.  The effect of laser surface texturing on transitions in lubrication regimes during unidirectional sliding contact. , 2005 .