IMPACT OF HEAT TRANSFER ON CENTRIFUGAL COMPRESSORS OF MICRO TURBINES

Micro turbines are small, high-speed gas turbine engines. When designed for a power output of 5 to 15 kW, micro turbines could provide the power for a household or a small set of units, serve as a range extender for hybrid electrical vehicles, or an auxiliary power unit to meet anti-idling requirements for heavyduty diesel truck engines. The smaller the gas turbine, the harder it however is to achieve a competitive efficiency. At the considered power level, manufacturing limitations become significant and heat transfer and fluid leaks start to dominate. Significant development in material science has enabled higher temperatures to be sustained, so that reasonable efficiencies could be obtained. Achieving these efficiencies however depends critically on limiting the effect of inter component heat transfer. In this paper the impact of heat losses on the performance of small centrifugal compressors are investigated. The paper presents the adaptation of a 1D design and performance analysis code to accommodate heat transfer effects. The modifications made to the code to account for heat transfer will be discussed and a validation of the adapted code will be given. After that the performance of several non-adiabatic compressor impellers will be discussed in detail. Design modifications will be presented that reduce the impact of heat transfer for the investigated compressors. The impact on heat transfer on the compressor maps will also be detailed.

[1]  Colin Rodgers,et al.  The Ubiquitous Personal Turbine—A Power Vision for the 21st Century , 2002 .

[2]  Colin Rodgers,et al.  Small recuperated ceramic microturbine demonstrator concept , 2008 .

[3]  M. Lygren.  Turbulent flow between a rotating and a stationary disk , 2001, Journal of Fluid Mechanics.

[4]  C. Rodgers.  Some Effects of Size on the Performances of Small Gas Turbines , 2003 .

[5]  Colin F. McDonald,et al.  Recuperator considerations for future higher efficiency microturbines , 2003 .

[6]  Karl Wygant,et al.  The Analysis of Heat Transfer in Automotive Turbochargers , 2010 .

[7]  J. Hétet,et al.  Turbocharger Heat Transfer Modeling Under Steady and Transient Conditions , 2009 .

[8]  T. M. Fesich,et al.  The Efficiency of Turbocharger Compressors With Diabatic Flows , 2010 .

[9]  Keith Robert Pullen,et al.  Design Overview of a Three Kilowatt Recuperated Ceramic Turboshaft Engine , 2010 .

[10]  Tom Verstraete,et al.  Multidisciplinary Optimization of a Radial Compressor for Microgas Turbine Applications , 2010 .

[11]  J. F. Gülich,et al.  Disk friction losses of closed turbomachine impellers , 2003 .

[12]  Ronald H. Aungier,et al.  Centrifugal Compressors: A Strategy for Aerodynamic Design and Analysis , 2000 .

[13]  Dieter Bohn,et al.  Conjugate Flow and Heat Transfer Investigation of a Turbo Charger: Part II — Experimental Results , 2003 .

[14]  J. F. Walton,et al.  Application of Foil Bearings to Turbomachinery Including Vertical Operation , 1999 .

[15]  Henry Cohen,et al.  Gas turbine theory , 1973 .

[16]  David Gordon Wilson,et al.  The design of high-efficiency turbomachinery and gas turbines , 1984 .

[17]  Bjoern Schenk.  Ceramic Turbine Engine Demonstration Project: A summary report , 2002 .

[18]  Paolo Fiorini,et al.  Micro power generation with micro gasturbines: a challenge , 2005 .

[19]  M. Rautenberg,,et al.  Influence of heat transfer between turbine and compressor on the performance of small turbochargers , 1984 .

[20]  Dries Verstraete,et al.  Development of a micro turboprop to extend altitude capabilities of small UAVs , 2011 .

[21]  Tom Verstraete,et al.  Numerical Study of the Heat Transfer in Micro Gas Turbines , 2007 .

[22]  Isashi Takehara,et al.  Summary of CGT302 Ceramic Gas Turbine Research and Development Program , 2002 .

[23]  Yves Ribaud,et al.  Overall thermodynamic model of an ultra micro turbine , 2004 .