The effect of thermomechanical parameters on the eutectic silicon characteristics in a non-modified cast A356 aluminum alloy

[1]  Man Zhu,et al.  Effects of T6 heat treatment on the microstructure, tensile properties, and fracture behavior of the modified A356 alloys , 2012 .

[2]  N. Haghdadi,et al.  The flow behavior modeling of cast A356 aluminum alloy at elevated temperatures considering the effect of strain , 2012 .

[3]  Y. C. Lin,et al.  A phenomenological constitutive model for high temperature flow stress prediction of Al–Cu–Mg alloy , 2012 .

[4]  Ali A. Roostaei,et al.  Constitutive base analysis of a 7075 aluminum alloy during hot compression testing , 2011 .

[5]  D. Apelian,et al.  Localized Recrystallization in Cast Al-Si-Mg Alloy during Solution Heat Treatment: Dilatometric and Calorimetric Studies , 2011 .

[6]  D. G. Mallapur,et al.  Studies on the influence of grain refining and modification on microstructure and mechanical properties of forged A356 alloy , 2011 .

[7]  H. Liao,et al.  Effect of Cold-rolling on Mechanical Properties and Microstructure of an Al-12%Si-0.2%Mg Alloy , 2011, Journal of Materials Engineering and Performance.

[8]  M. R. Toroghinejad,et al.  Significant improvement of semi-solid microstructure and mechanical properties of A356 alloy by ARB process , 2011 .

[9]  D. G. Mallapur,et al.  Influence of Ti, B and Sr on the microstructure and mechanical properties of A356 alloy , 2011 .

[10]  D. Apelian,et al.  Solution Treatment Effects on Microstructure and Mechanical Properties of Al-(1 to 13 pct)Si-Mg Cast Alloys , 2011 .

[11]  Y. Lin,et al.  Constitutive descriptions for hot compressed 2124-T851 aluminum alloy over a wide range of temperature and strain rate , 2010 .

[12]  Liao Heng-cheng,et al.  Effect of hot extrusion on mechanical properties and microstructure of near eutectic Al–12.0%Si–0.2%Mg alloy , 2010 .

[13]  M. Haghshenas,et al.  Hot deformation behaviour of thixocast Al–Si–Mg alloy during compression at elevated temperatures , 2010 .

[14]  M. Jahazi,et al.  An investigation to the effect of deformation-heat treatment cycle on the eutectic morphology and mechanical properties of a Thixocast A356 alloy , 2009 .

[15]  I. Kovačević.  Simulation of spheroidisation of elongated Si-particle in Al–Si alloys by the phase-field model , 2008 .

[16]  O. Reiso,et al.  Annealing of Al–Si alloys after equal-channel angular pressing , 2008 .

[17]  M. Haghshenas,et al.  The effects of thermo-mechanical parameters on the microstructure of Thixocast A356 aluminum alloy , 2008 .

[18]  A. Samuel,et al.  The effects of mischmetal, cooling rate and heat treatment on the eutectic Si particle characteristics of A319.1, A356.2 and A413.1 Al-Si casting alloys , 2008 .

[19]  Jue Zhong,et al.  Constitutive modeling for elevated temperature flow behavior of 42CrMo steel , 2008 .

[20]  M. Tiryakioğlu.  Si particle size and aspect ratio distributions in an Al–7%Si–0.6%Mg alloy during solution treatment , 2008 .

[21]  M. Zhang,et al.  Refinement of eutectic grains by combined addition of strontium and boron in near-eutectic Al–Si alloys , 2007 .

[22]  T. Langdon,et al.  Particle and grain growth in an Al-Si alloy during high-pressure torsion , 2007 .

[23]  D. G. Morris,et al.  Contribution of microstructural parameters to strengthening in an ultrafine-grained Al-7%Si alloy processed by severe deformation , 2007 .

[24]  R. Mishra,et al.  Effect of friction stir processing on the microstructure of cast A356 aluminum , 2006 .

[25]  S. Youn,et al.  Characterization of age-hardening behavior of eutectic region in squeeze-cast A356-T5 alloy using nanoindenter and atomic force microscope , 2006 .

[26]  D. Apelian,et al.  Effects of rapid heating on aging characteristics of T6 tempered Al–Si–Mg alloys using a fluidized bed , 2006 .

[27]  D. Apelian,et al.  Effects of rapid heating on solutionizing characteristics of Al-Si-Mg alloys using a fluidized bed , 2006 .

[28]  Arne K. Dahle,et al.  Three-dimensional analysis of eutectic grains in hypoeutectic Al-Si alloys , 2005 .

[29]  F. Akhlaghi,et al.  Effects of casting temperature on the microstructure and wear resistance of compocast A356/SiCp composites: a comparison between SS and SL routes , 2004 .

[30]  Daan M. Maijer,et al.  Constitutive behaviour of A356 during the quenching operation , 2004 .

[31]  Q. Wang,et al.  Plastic deformation behavior of aluminum casting alloys A356/357 , 2004 .

[32]  D. Shu,et al.  Effects of melt thermal treatment on hypoeutectic Al–Si alloys , 2002 .

[33]  P. Uggowitzer,et al.  On the silicon spheroidization in Al-Si alloys , 2002 .

[34]  Y. Bréchet,et al.  On the mechanisms of dynamic recovery , 2002 .

[35]  P. Uggowitzer,et al.  Silicon Spheroidization Treatment of Thixoformed Al-Si-Mg Alloys , 2002 .

[36]  C. M. Sellars,et al.  The effect of β, β′ and β″ precipitates in a homogenised AA6063 alloy on the hot deformability and the peak hardness , 2001 .

[37]  P. Voorhees,et al.  THE DEVELOPMENT OF SPATIAL CORRELATIONS DURING OSTWALD RIPENING: A TEST OF THEORY , 2000 .

[38]  W. S. Miller,et al.  Recent development in aluminium alloys for aerospace applications , 2000 .

[39]  Gordon Blount,et al.  The suitability of aluminium as an alternative material for car bodies , 1999 .

[40]  Mark F. Horstemeyer,et al.  Effect of temperature on silicon particle damage in A356 alloy , 1998 .

[41]  F. J. Humphreys,et al.  Recrystallization and Related Annealing Phenomena , 1995 .

[42]  E. Evangelista,et al.  Precipitation effects during hot deformation of a copper alloy , 1994 .