Hot Deformation Behavior and Microstructure Characterization of an Al-Cu-Li-Mg-Ag Alloy

The flow behavior of an Al-Cu-Li-Mg-Ag alloy was studied by thermal simulation tests at deformation temperatures between 350 °C and 470 °C and strain rates between 0.01–10 s−1. The microstructures of the deformed materials were characterized by electron backscattered diffraction. Constitutive equations were developed after considering compensation for strains. The processing maps were established and the optimum processing window was identified. The experimental data and predicted values of flow stresses were in a good agreement with each other. The influence of deformation temperature and strain rates on the microstructure were discussed. The relationship between the recrystallization mechanism and the Zener–Hollomon parameter was investigated as well.

[1]  A. S. Ahmad,et al.  Modified kinetic model for describing continuous dynamic recrystallization behavior of Al 2219 alloy during hot deformation process , 2020 .

[2]  Lin Jun,et al.  Hot deformation behavior of 7A04 aluminum alloy at elevated temperature: constitutive modeling and verification , 2020, International Journal of Material Forming.

[3]  Yun-lai Deng,et al.  Influence of strain rate on hot deformation behavior and recrystallization behavior under isothermal compression of Al-Zn-Mg-Cu alloy , 2019, Journal of Alloys and Compounds.

[4]  B. Liao,et al.  The microstructural evolution of aluminum alloy 7055 manufactured by hot thermo-mechanical process , 2019, Journal of Alloys and Compounds.

[5]  Guoqun Zhao,et al.  Constitutive modeling, processing map establishment and microstructure analysis of spray deposited Al-Cu-Li alloy 2195 , 2019, Journal of Alloys and Compounds.

[6]  Zhenghua Tang,et al.  The flow behavior of homogenizated Al-Mg-Si-La aluminum alloy during hot deformation , 2019, Materials Research Express.

[7]  Guoqun Zhao,et al.  Investigation of dynamic recrystallization and modeling of microstructure evolution of an Al-Mg-Si aluminum alloy during high-temperature deformation , 2019, Journal of Alloys and Compounds.

[8]  W. Misiolek,et al.  Analysis of flow stress and microstructure during hot compression of 6099 aluminum alloy (AA6099) , 2019, Materials Science and Engineering: A.

[9]  M. Couper,et al.  Effect of Heat Treatment Condition on the Flow Behavior and Recrystallization Mechanisms of Aluminum Alloy 7055 , 2019, Materials.

[10]  Q. Pan,et al.  Characterization of hot deformation behavior and constitutive modeling of Al–Mg–Si–Mn–Cr alloy , 2018, Journal of Materials Science.

[11]  Wen You,et al.  Characteristic constitution model and microstructure of an Al-3.5Cu-1.5Li alloy subjected to thermal deformation , 2018, Materials Characterization.

[12]  Xingwei Zheng,et al.  Plastic flow behavior and microstructure characteristics of light-weight 2060 Al-Li alloy , 2018, Materials Science and Engineering: A.

[13]  N. Nayan,et al.  Effect of temperature and strain rate on hot deformation behavior and microstructure of Al-Cu-Li alloy , 2017 .

[14]  J. Zhai,et al.  Crystallization kinetics, breakdown strength, and energy-storage properties in niobate-based glass-ceramics , 2017 .

[15]  Ke Huang,et al.  A review of dynamic recrystallization phenomena in metallic materials , 2016 .

[16]  Yu-tao Zhao,et al.  Hot deformation behavior and optimization of processing parameters of a typical high-strength Al–Mg–Si alloy , 2016 .

[17]  Y. Nie,et al.  Hot deformation behavior of 2060 alloy , 2015 .

[18]  Zhiming Yu,et al.  Characterization of Hot Deformation Behavior of a Novel Al–Cu–Li Alloy Using Processing Maps , 2015, Acta Metallurgica Sinica (English Letters).

[19]  Xinyun Wang,et al.  A new dynamic recrystallisation model of an extruded Al-Cu-Li alloy during high-temperature deformation , 2015 .

[20]  Guoqun Zhao,et al.  Constitutive analysis of homogenized 7005 aluminum alloy at evaluated temperature for extrusion process , 2015 .

[21]  Z. Yin,et al.  Characterization of hot deformation behavior of as-homogenized Al–Cu–Li–Sc–Zr alloy using processing maps , 2014 .

[22]  J. Shen,et al.  Flow behavior and processing maps of 2099 alloy , 2014 .

[23]  Desheng Huang,et al.  Processing maps and microstructural evolution of isothermal compressed Al–Cu–Li alloy , 2013 .

[24]  Nikolaos D. Alexopoulos,et al.  Fatigue behavior of the aeronautical Al–Li (2198) aluminum alloy under constant amplitude loading , 2013 .

[25]  Xinyun Wang,et al.  High temperature deformation behavior and optimal hot processing parameters of Al-Si eutectic alloy , 2013 .

[26]  Fuguo Li,et al.  Flow behavior modeling of the 7050 aluminum alloy at elevated temperatures considering the compensation of strain , 2012 .

[27]  R. Rioja,et al.  The Evolution of Al-Li Base Products for Aerospace and Space Applications , 2012, Metallurgical and Materials Transactions A.

[28]  E. Evangelista.  Hot Deformation and Processing of Aluminum Alloys , 2011 .

[29]  A. K. Bhaduri,et al.  A Study on Microstructural Evolution and Dynamic Recrystallization During Isothermal Deformation of a Ti-Modified Austenitic Stainless Steel , 2011 .

[30]  Ichiko Shimizu.  Theories and applicability of grain size piezometers : The role of dynamic recrystallization mechanisms , 2008 .

[31]  A. Taheri,et al.  Experimental investigation of the hot deformation behavior of AA7075: Development and comparison of flow localization parameter and dynamic material model processing maps , 2014 .