Optimization of cutting parameters based on surface roughness and assistance of workpiece surface temperature in turning process

Problem statement: In machining operation, the quality of surface finish is an important requirement for many turned workpieces. Thus, the choice of optimized cutting parameters is very important for controlling the required surface quality. Approach: The focus of present experimental study is to optimize the cutting parameters using two performance measures, workpiece surface temperature and surface roughness. Optimal cutting parameters for each performance measure were obtained employing Taguchi techniques. The orthogonal array, signal to noise ratio and analysis of variance were employed to study the performance characteristics in turning operation. Results: The experimental results showed that the workpiece surface temperature can be sensed and used effectively as an indicator to control the cutting performance and improves the optimization process. Conclusion: Thus, it is possible to increase machine utilization and decrease production cost in an automated manufacturing environment.

[1]  Dong Young Jang,et al.  Study of the correlation between surface roughness and cutting vibrations to develop an on-line roughness measuring technique in hard turning , 1996 .

[2]  Y. S. Tarng,et al.  Design optimization of cutting parameters for turning operations based on the Taguchi method , 1998 .

[3]  Sun Fanghong,et al.  Experimental research on the dynamic characteristics of the cutting temperature in the process of high-speed milling , 2003 .

[4]  M. Guillot,et al.  On-line prediction of surface finish and dimensional deviation in turning using neural network based sensor fusion , 1997 .

[5]  Janez Kopac,et al.  Optimal machining parameters for achieving the desired surface roughness in fine turning of cold pre-formed steel workpieces , 2002 .

[6]  G. Robin Henderson.  Six Sigma Quality Improvement with Minitab , 2006 .

[7]  Jae-Seob Kwak,et al.  Application of Taguchi and response surface methodologies for geometric error in surface grinding process , 2005 .

[8]  James Wallbank,et al.  Cutting temperature: prediction and measurement methods—a review , 1999 .

[9]  John L. Yang.  A Systematic Approach for Identifying Optimum Surface Roughness Performance in End-Milling Operations By Mr . , 2001 .

[10]  R. A. Collacott.  Condition monitoring by sound analysis , 1975 .

[11]  Fu Gang Yan,et al.  Cutting temperature and tool wear of hard turning hardened bearing steel , 2002 .

[12]  Chris Sauer,et al.  Winners and losers in the digital divide , 2002, J. Inf. Technol..

[13]  Indrajit Mukherjee,et al.  A review of optimization techniques in metal cutting processes , 2006, Comput. Ind. Eng..

[14]  B. Lee,et al.  Modeling the surface roughness and cutting force for turning , 2001 .

[15]  J. M. Longbottom,et al.  Cutting temperature measurement while machining – a review , 2005 .

[16]  George-Christopher Vosniakos,et al.  Predicting surface roughness in machining: a review , 2003 .

[17]  Joseph C. Chen,et al.  Development of a fuzzy-nets-based in-process surface roughness adaptive control system in turning operations , 2006, Expert Syst. Appl..

[18]  Minitab.  Statistical Methods for Quality Improvement , 2001 .

[19]  Doris A. Weisman,et al.  Experimental Design With Applications in Management, Engineering and the Sciences , 2003, Technometrics.

[20]  Ossama B. Abouelatta,et al.  Surface roughness prediction based on cutting parameters and tool vibrations in turning operations , 2001 .

[21]  Sounak Kumar Choudhury,et al.  On-line control of machine tool vibration during turning operation , 1995 .

[22]  J. Paulo Davim,et al.  A note on the determination of optimal cutting conditions for surface finish obtained in turning using design of experiments , 2001 .