Machining Characteristics of Polycrystalline Silicon by Wire Electrical Discharge Machining
暂无分享,去创建一个
Biing-Hwa Yan | Hsiang-Kuo Lee | B. Yan | F. Huang | Po-Huai Yu | Yang-Xin Lin | Hsiang-Kuo Lee | F. Y. Huang | P. Yu | Yang-Xin Lin | Shi-jie Qin | Shi-Jie Qin
[1] T. Yue,et al. Wire Electrochemical Discharge Machining of Al2O3 Particle Reinforced Aluminum Alloy 6061 , 2009 .
[2] Masanori Kunieda,et al. Improvement of EDM efficiency of silicon single crystal through ohmic contact , 2000 .
[3] M. Ghoreishi,et al. Investigation into the Effect of Voltage Excitation of Pre-Ignition Spark Pulse on the Electro-Discharge Machining (EDM) Process , 2007 .
[4] Masanori Kunieda,et al. High-quality cutting of polished single-crystal silicon by wire electrical discharge machining , 2005 .
[5] Kuang-Yuan Kung,et al. Modeling and Analysis of Machinability Evaluation in the Wire Electrical Discharge Machining (WEDM) Process of Aluminum Oxide-Based Ceramic , 2008 .
[6] Ching-Tien Lin,et al. Electrical Discharge Machining (EDM) Characteristics Associated with Electrical Discharge Energy on Machining of Cemented Tungsten Carbide , 2008 .
[7] Hans Joachim Möller,et al. Wafering of silicon crystals , 2006 .
[8] Y. H. Guu,et al. An Experimental Study on Electrical Discharge Machining of Manganese–Zinc Ferrite Magnetic Material , 2007 .
[9] Y. F. Luo,et al. Investigation of silicon wafering by wire EDM , 1992 .
[10] Dave Kim,et al. Electrical Discharge Machining of Functionally Graded 15–35 Vol% SiCp/Al Composites , 2006 .
[11] Zhi-Dong Liu,et al. High efficiency slicing of low resistance silicon ingot by wire electrolytic-spark hybrid machining , 2009 .
[12] Ammar Sami Mohammad,et al. Experimental Study of Conventional Wire Electrical Discharge Machining for Microfabrication , 2008 .
[13] Yunn-Shiuan Liao,et al. Study of electrical discharge machining technology for slicing silicon ingots , 2003 .
[14] D. Helmreich,et al. MULTICRYSTALLINE SILICON FOR SOLAR CELLS , 1982 .
[15] M. Kunieda,et al. Contouring of polished single-crystal silicon plates by wire electrical discharge machining , 2007 .
[16] Pulak M. Pandey,et al. Understanding the Role of Weight Percentage and Size of Silicon Carbide Particulate Reinforcement on Electro-Discharge Machining of Aluminium-Based Composites , 2008 .
[17] L. Hwang,et al. Machining Characteristics and Optimization of Machining Parameters of SKH 57 High-Speed Steel Using Electrical-Discharge Machining Based on Taguchi Method , 2006 .
[18] Hans Joachim Möller,et al. Basic Mechanisms and Models of Multi‐Wire Sawing , 2004 .
[19] L. Froyen,et al. Surface and Sub‐Surface Quality of Steel after EDM , 2006 .
[20] Masanori Kunieda,et al. Cutting of polished single-crystal silicon by wire electrical discharge machining , 2004 .
[21] Yusuf Keskin,et al. An experimental study for determination of the effects of machining parameters on surface roughness in electrical discharge machining (EDM) , 2006 .