A Review on the Thermal Hazards of the Lithium-Ion Battery and the Corresponding Countermeasures

As one of the most promising new energy sources, the lithium-ion battery (LIB) and its associated safety concerns have attracted great research interest. Herein, a comprehensive review on the thermal hazards of LIBs and the corresponding countermeasures is provided. In general, the thermal hazards of the LIB can be caused or aggravated by several factors including physical, electrical and thermal factors, manufacturing defect and even battery aging. Due to the activity and combustibility of traditional battery components, they usually possess a relatively high thermal hazard and a series of side reactions between electrodes and electrolytes may occur under abusive conditions, which would further lead to the thermal failure of LIBs. Besides, the thermal hazards generally manifest as the thermal runaway behaviors such as high-temperature, ejection, combustion, explosion and toxic gases for a single battery, and it can even evolve to thermal failure propagation within a battery pack. To decrease these hazards, some countermeasures are reviewed including the application of safety devices, fire-retardant additives, battery management systems, hazard warnings and firefighting should a hazard occur.

[1]  Jun Zhang,et al.  Effects of low air pressure on radiation-controlled rectangular ethanol and n-heptane pool fires , 2013 .

[2]  Toh-Ming Lu,et al.  Utilizing van der Waals Slippery Interfaces to Enhance the Electrochemical Stability of Silicon Film Anodes in Lithium-Ion Batteries. , 2018, ACS applied materials & interfaces.

[3]  Bruno Scrosati,et al.  High-performance electrode materials for lithium-ion batteries for electric vehicles , 2015 .

[4]  Paul R. Shearing,et al.  Pilot-scale continuous synthesis of a vanadium-doped LiFePO4/C nanocomposite high-rate cathodes for lithium-ion batteries , 2016 .

[5]  Hui Zhang,et al.  Experimental study of large-scale fire behavior under low pressure at high altitude , 2013 .

[6]  Debasish Mohanty,et al.  Effect of electrode manufacturing defects on electrochemical performance of lithium-ion batteries: Cognizance of the battery failure sources , 2016 .

[7]  Yan Yu,et al.  A Review on Lithium-Ion Batteries Safety Issues: Existing Problems and Possible Solutions , 2012 .

[8]  Xuning Feng,et al.  Thermal runaway mechanism of lithium ion battery for electric vehicles: A review , 2018 .

[9]  Xiaoyu Jiang,et al.  Bis(2,2,2-trifluoroethyl) methylphosphonate: An Novel Flame-retardant Additive for Safe Lithium-ion Battery , 2014 .

[10]  Fei Chen,et al.  Field assisted sintering of dense Al-substituted cubic phase Li7La3Zr2O12 solid electrolytes , 2014 .

[11]  Jeff Dahn,et al.  The Impact of Vinylene Carbonate, Fluoroethylene Carbonate and Vinyl Ethylene Carbonate Electrolyte Additives on Electrode/Electrolyte Reactivity Studied Using Accelerating Rate Calorimetry , 2014 .

[12]  Richard K.K. Yuen,et al.  Investigation of enclosure effect of pressure chamber on the burning behavior of a hydrocarbon fuel , 2016 .

[13]  Binggang Cao,et al.  Three-dimensional thermal finite element modeling of lithium-ion battery in thermal abuse application , 2010 .

[14]  Richard E Lyon,et al.  Energetics of lithium ion battery failure. , 2016, Journal of hazardous materials.

[15]  Jun Chen,et al.  α‐Fe2O3 Nanotubes in Gas Sensor and Lithium‐Ion Battery Applications , 2005 .

[16]  John B. Kerr,et al.  The role of Li-ion battery electrolyte reactivity in performance decline and self-discharge , 2003 .

[17]  F. J. Diez,et al.  The effect of pressure and oxygen concentration on the combustion of PMMA , 2013 .

[18]  Michael Pecht,et al.  Analysis of Manufacturing-Induced Defects and Structural Deformations in Lithium-Ion Batteries Using Computed Tomography , 2018 .

[19]  Feng Pei,et al.  An electrochemically compatible and flame-retardant electrolyte additive for safe lithium ion batteries , 2013 .

[20]  Pengjian Zuo,et al.  Capacity fading mechanism during long-term cycling of over-discharged LiCoO2/mesocarbon microbeads battery , 2015 .

[21]  M. Morcrette,et al.  Investigation on the fire-induced hazards of Li-ion battery cells by fire calorimetry , 2012 .

[22]  Hajime Miyashiro,et al.  All-solid-state lithium secondary battery with ceramic/polymer composite electrolyte , 2002 .

[23]  J. Dahn,et al.  Thermal Model of Cylindrical and Prismatic Lithium-Ion Cells , 2001 .

[24]  N. P. Yao,et al.  Heat Transfer in Lead‐Acid Batteries Designed for Electric‐Vehicle Propulsion Application , 1979 .

[25]  J. Yamaki,et al.  Thermal stability of graphite anode with electrolyte in lithium-ion cells , 2002 .

[26]  Viktor Hacker,et al.  Thermal-runaway experiments on consumer Li-ion batteries with metal-oxide and olivin-type cathodes , 2014 .

[27]  Jeong-Hoon Kim,et al.  Inverse opal-inspired, nanoscaffold battery separators: a new membrane opportunity for high-performance energy storage systems. , 2014, Nano letters.

[28]  Hongxia Geng,et al.  Role of amorphous boundary layer in enhancing ionic conductivity of lithium–lanthanum–titanate electrolyte , 2010 .

[29]  Xuan Liu,et al.  Comprehensive calorimetry of the thermally-induced failure of a lithium ion battery , 2015 .

[30]  Xinping Qiu,et al.  Toxicity, a serious concern of thermal runaway from commercial Li-ion battery ☆ , 2016 .

[31]  Jeff Dahn,et al.  Ternary Electrolyte Additive Mixtures for Li-Ion Cells that Promote Long Lifetime and Less Reactivity with Charged Electrodes at Elevated Temperatures , 2015 .

[32]  Zhonghao Rao,et al.  An experimental study on thermal management of lithium ion battery packs using an improved passive method , 2018 .

[33]  Zheng Wang,et al.  Densification and ionic-conduction improvement of lithium garnet solid electrolytes by flowing oxygen sintering , 2014 .

[34]  Sher Bahadar Khan,et al.  Structure and thermal properties of octadecane/expanded graphite composites as shape-stabilized phase change materials , 2016 .

[35]  Philip N. Ross,et al.  Thermal Stability of LiPF6 Salt and Li-ion Battery Electrolytes Containing LiPF6 , 2006 .

[36]  Zheng Wang,et al.  Safety influences of the Al and Ti elements modified LiCoO2 materials on LiCoO2/graphite batteries under the abusive conditions , 2019, Electrochimica Acta.

[37]  Ibrahim Dincer,et al.  Novel thermal management system using boiling cooling for high-powered lithium-ion battery packs for hybrid electric vehicles , 2017 .

[38]  Jeff Dahn,et al.  A systematic study on the reactivity of different grades of charged Li[Ni x Mn y Co z ]O 2 with electrolyte at elevated temperatures using accelerating rate calorimetry , 2016 .

[39]  Partha P. Mukherjee,et al.  Probing the cooling effectiveness of phase change materials on lithium-ion battery thermal response under overcharge condition , 2018 .

[40]  Qingsong Wang,et al.  Thermal Behavior of Lithiated Graphite with Electrolyte in Lithium-Ion Batteries , 2006 .

[41]  Chun Yang,et al.  Thermal analysis of conjugated cooling configurations using phase change material and liquid cooling techniques for a battery module , 2019, International Journal of Heat and Mass Transfer.

[42]  Wen Tong Chong,et al.  Computational fluid dynamic and thermal analysis of Lithium-ion battery pack with air cooling , 2016 .

[43]  Guoming Chen,et al.  Study on degradation behavior of commercial 18650 LiAlNiCoO2 cells in over‐charge conditions , 2018, International Journal of Energy Research.

[44]  Christian Veje,et al.  Numerical analysis of heat propagation in a battery pack using a novel technology for triggering thermal runaway , 2017 .

[45]  Gi‐Heon Kim,et al.  A three-dimensional thermal abuse model for lithium-ion cells , 2007 .

[46]  Song Lu,et al.  Ignition and combustion characteristics of lithium ion batteries under low atmospheric pressure , 2018, Energy.

[47]  Jian Wang,et al.  Combustion characteristics of n-heptane at high altitudes , 2011 .

[48]  Michael Pecht,et al.  Li-Ion Battery Fire Hazards and Safety Strategies , 2018, Energies.

[49]  Kang Xu,et al.  A new approach toward improved low temperature performance of Li-ion battery , 2002 .

[50]  Jian Wang,et al.  Investigation into the Fire Hazards of Lithium-Ion Batteries under Overcharging , 2017 .

[51]  Wu Xu,et al.  Weakly Coordinating Anions, and the Exceptional Conductivity of Their Nonaqueous Solutions , 2001 .

[52]  Jeff Dahn,et al.  Studies of the Effect of High Voltage on the Impedance and Cycling Performance of Li[Ni0.4Mn0.4Co0.2]O2/Graphite Lithium-Ion Pouch Cells , 2015 .

[53]  Pascal Henry Biwole,et al.  Electric vehicles batteries thermal management systems employing phase change materials , 2018 .

[54]  Feng Wu,et al.  Ethoxy (pentafluoro) cyclotriphosphazene (PFPN) as a multi-functional flame retardant electrolyte additive for lithium-ion batteries , 2018 .

[55]  Mingyi Chen,et al.  Investigation on the thermal hazards of 18650 lithium ion batteries by fire calorimeter , 2015, Journal of Thermal Analysis and Calorimetry.

[56]  Martin Winter,et al.  Post-Mortem Investigations of Fluorinated Flame Retardants for Lithium Ion Battery Electrolytes by Gas Chromatography with Chemical Ionization , 2017 .

[57]  Qingsong Wang,et al.  Enhancing the safety of lithium ion batteries by 4-isopropyl phenyl diphenyl phosphate , 2007 .

[58]  H. Maleki,et al.  Thermal Stability Studies of Li‐Ion Cells and Components , 1999 .

[59]  Qingsong Wang,et al.  A review of lithium ion battery failure mechanisms and fire prevention strategies , 2019, Progress in Energy and Combustion Science.

[60]  Kang Xu,et al.  An Attempt to Formulate Nonflammable Lithium Ion Electrolytes with Alkyl Phosphates and Phosphazenes , 2002 .

[61]  Susan L. Rose-Pehrsson,et al.  Physical and chemical analysis of lithium-ion battery cell-to-cell failure events inside custom fire chamber , 2015 .

[62]  Yi Cui,et al.  Stable cycling of double-walled silicon nanotube battery anodes through solid-electrolyte interphase control. , 2012, Nature nanotechnology.

[63]  Daniel H. Doughty,et al.  A General Discussion of Li Ion Battery Safety , 2012 .

[64]  Bo Zhang,et al.  Sustainable, heat-resistant and flame-retardant cellulose-based composite separator for high-performance lithium ion battery , 2014, Scientific Reports.

[65]  Jingwen Weng,et al.  Investigation of a commercial lithium-ion battery under overcharge/over-discharge failure conditions , 2018, RSC advances.

[66]  Jingwen Weng,et al.  Thermal Failure Propagation in Lithium-Ion Battery Modules with Various Shapes , 2018, Applied Sciences.

[67]  Yaping He,et al.  Effects of oblique air flow on burning rates of square ethanol pool fires. , 2013, Journal of hazardous materials.

[68]  Ran Tu,et al.  Influence of low air pressure on combustion characteristics and flame pulsation frequency of pool fires , 2011 .

[69]  J. Dahn,et al.  The Effect of Some Nitriles as Electrolyte Additives in Li-Ion Batteries , 2015 .

[70]  Paul A. Nelson,et al.  Modeling thermal management of lithium-ion PNGV batteries , 2002 .

[71]  Zhengguo Zhang,et al.  Compact liquid cooling strategy with phase change materials for Li-ion batteries optimized using response surface methodology , 2018, Applied Energy.

[72]  Per Blomqvist,et al.  Toxic fluoride gas emissions from lithium-ion battery fires , 2017, Scientific Reports.

[73]  Weixiong Wu,et al.  Low‐temperature reversible capacity loss and aging mechanism in lithium‐ion batteries for different discharge profiles , 2018, International Journal of Energy Research.

[74]  Yingni Yang,et al.  Preparation and thermal properties of polyethylene glycol/expanded graphite as novel form-stable phase change material for indoor energy saving , 2018 .

[75]  Shun-bing Zhu,et al.  Research and development of fire extinguishing technology for power lithium batteries , 2018 .

[76]  Shi-Gang Sun,et al.  LiMn0.5Fe0.5PO4 solid solution materials synthesized by rheological phase reaction and their excellent electrochemical performances as cathode of lithium ion battery , 2013 .

[77]  Sai-Cheong Chung,et al.  Optimized LiFePO4 for Lithium Battery Cathodes , 2001 .

[78]  Joshua R. Gaffen,et al.  Phosphoryl-rich flame-retardant ions (FRIONs): towards safer lithium-ion batteries. , 2014, Angewandte Chemie.

[79]  Yuji Hasemi,et al.  Predicting the pyrolysis of wood considering char oxidation under different ambient oxygen concentrations , 2006 .

[80]  S. Kjelstrup,et al.  Measurements of ageing and thermal conductivity in a secondary NMC-hard carbon Li-ion battery and the impact on internal temperature profiles , 2017 .

[81]  Christopher J. Orendorff,et al.  Failure propagation in multi-cell lithium ion batteries , 2015 .

[82]  Jianqiu Li,et al.  A review on the key issues for lithium-ion battery management in electric vehicles , 2013 .

[83]  Ralph E. White,et al.  Capacity fade of Sony 18650 cells cycled at elevated temperatures. Part II. Capacity fade analysis , 2002 .

[84]  Yong Yang,et al.  Toward a stable electrochemical interphase with enhanced safety on high-voltage LiCoO 2 cathode: A case of phosphazene additives , 2017 .

[85]  Shuangfeng Wang,et al.  Experimental investigations of Alum/expanded graphite composite phase change material for thermal energy storage and its compatibility with metals , 2018, Energy.

[86]  Xuning Feng,et al.  Low temperature aging mechanism identification and lithium deposition in a large format lithium iron phosphate battery for different charge profiles , 2015 .

[87]  Jian Wang,et al.  Fire behavior of lithium-ion battery with different states of charge induced by high incident heat fluxes , 2019, Journal of Thermal Analysis and Calorimetry.

[88]  G. Venugopal.  Characterization of thermal cut-off mechanisms in prismatic lithium-ion batteries , 2001 .

[89]  Mingyi Chen,et al.  Study of the fire hazards of lithium-ion batteries at different pressures , 2017 .

[90]  Bo Liang,et al.  Design and parametric optimization of thermal management of lithium-ion battery module with reciprocating air-flow , 2015 .

[91]  Doron Aurbach,et al.  Calorimetric studies of the thermal stability of electrolyte solutions based on alkyl carbonates and the effect of the contact with lithium , 2005 .

[92]  F. Larsson,et al.  Using FTIR to determine toxic gases in fires with Li-ion batteries , 2016 .

[93]  Hassan Fathabadi,et al.  High thermal performance lithium-ion battery pack including hybrid active–passive thermal management system for using in hybrid/electric vehicles , 2014 .

[94]  Yunhong Zhou,et al.  Safe positive temperature coefficient composite cathode for lithium ion battery , 2012 .

[95]  Yanglong Hou,et al.  A simple route to improve rate performance of LiFePO 4 /reduced graphene oxide composite cathode by adding Mg 2+ via mechanical mixing , 2017 .

[96]  Xuning Feng,et al.  Mechanisms for the evolution of cell variations within a LiNixCoyMnzO2/graphite lithium-ion battery pack caused by temperature non-uniformity , 2018, Journal of Cleaner Production.

[97]  Chuanjian Zhang,et al.  Renewable and superior thermal-resistant cellulose-based composite nonwoven as lithium-ion battery separator. , 2013, ACS Applied Materials and Interfaces.

[98]  Tae-Hee Kim,et al.  Electronegativity-induced enhancement of thermal stability by succinonitrile as an additive for Li ion batteries , 2011 .

[99]  Nathan S Lewis,et al.  Research opportunities to advance solar energy utilization , 2016, Science.

[100]  Weixiong Wu,et al.  A critical review of battery thermal performance and liquid based battery thermal management , 2019, Energy Conversion and Management.

[101]  Jiateng Zhao,et al.  Thermal management of cylindrical power battery module for extending the life of new energy electric vehicles , 2015 .

[102]  Christopher K. Dyer.  Fuel cells for portable applications , 2002 .

[103]  Jian Wang,et al.  A study on the fire behaviors of 18650 battery and batteries pack under discharge , 2018, Journal of Thermal Analysis and Calorimetry.

[104]  Yuji Kojima,et al.  Effect of Mg-doping on the degradation of LiNiO2-based cathode materials by combined spectroscopic methods , 2012 .

[105]  Yair Ein-Eli,et al.  Higher, Stronger, Better…︁ A Review of 5 Volt Cathode Materials for Advanced Lithium‐Ion Batteries , 2012 .

[106]  Ralph E. White,et al.  A lumped model of venting during thermal runaway in a cylindrical Lithium Cobalt Oxide lithium-ion cell , 2016 .

[107]  Lu Cai,et al.  Probing Li-Ni Cation Disorder in Li1-xNi1+x-yAlyO2 Cathode Materials by Neutron Diffraction , 2012 .

[108]  J. Darkwa,et al.  Enhanced laminated composite phase change material for energy storage , 2011 .

[109]  Zhaolin Liu,et al.  Synthesis and characterization of LiNi1−x−yCoxMnyO2 as the cathode materials of secondary lithium batteries , 1999 .

[110]  Carlos Fernandez-Pello,et al.  The combined effect of pressure and oxygen concentration on piloted ignition of a solid combustible , 2010 .

[111]  Diego Lisbona,et al.  A review of hazards associated with primary lithium and lithium-ion batteries , 2011 .

[112]  Ralph E. White,et al.  Characterization of Commercially Available Lithium-Ion Batteries , 1998 .

[113]  Hlynur Stefansson,et al.  Potential use of geothermal energy sources for the production of lithium-ion batteries , 2011 .

[114]  J. Dahn,et al.  Accelerating Rate Calorimetry Study on the Thermal Stability of Lithium Intercalated Graphite in Electrolyte. I. Experimental , 1999 .

[115]  D. Abraham,et al.  Diagnostic examination of thermally abused high-power lithium-ion cells , 2006 .

[116]  Ronald H. Reif,et al.  Lithium Battery Safety: A look at Woods Hole Oceanographic Institution’s Program , 2010 .

[117]  Srinivas Garimella,et al.  Passive, internal thermal management system for batteries using microscale liquid–vapor phase change , 2013 .

[118]  Li Li,et al.  An investigation of functionalized electrolyte using succinonitrile additive for high voltage lithium-ion batteries , 2016 .

[119]  Liu Quanyi,et al.  Experimental Study of N-Heptane Pool Fire Behaviors under Dynamic Pressures in an Altitude Chamber , 2013 .

[120]  Martin Winter,et al.  Influence of the Fluorination Degree of Organophosphates on Flammability and Electrochemical Performance in Lithium Ion Batteries: Studies on Fluorinated Compounds Deriving from Triethyl Phosphate , 2016 .

[121]  Kun Dai,et al.  Positive Temperature Coefficient (PTC) Evolution of Segregated Structural Conductive Polypropylene Nanocomposites with Visually Traceable Carbon Black Conductive Network , 2017 .

[122]  Dmitry Belov,et al.  Failure mechanism of Li-ion battery at overcharge conditions , 2008 .

[123]  Guoqing Zhang,et al.  Experimental examination of large capacity liFePO4 battery pack at high temperature and rapid discharge using novel liquid cooling strategy , 2018 .

[124]  Kun Dai,et al.  Heating-induced negative temperature coefficient effect in conductive graphene/polymer ternary nanocomposites with a segregated and double-percolated structure , 2017 .

[125]  Yu Shi,et al.  Optimisation with adiabatic interlayers for liquid-dominated cooling system on fast charging battery packs , 2019, Applied Thermal Engineering.

[126]  Mingyi Chen,et al.  Combustion characteristics of primary lithium battery at two altitudes , 2016, Journal of Thermal Analysis and Calorimetry.

[127]  T. P. Kumar,et al.  Safety mechanisms in lithium-ion batteries , 2006 .

[128]  Jiajie Yao,et al.  Experimental study of small scale n-heptane pool fire with water bath in an altitude chamber , 2015 .

[129]  John B. Goodenough,et al.  LixCoO2 (0, 1980 .

[130]  Richard K.K. Yuen,et al.  The burning behaviors of pool fire flames under low pressure , 2016 .

[131]  S. Nada,et al.  Numerical investigations of using carbon foam/PCM/Nano carbon tubes composites in thermal management of electronic equipment , 2015 .

[132]  Kyung Yoon Chung,et al.  Investigation of Changes in the Surface Structure of LixNi0.8Co0.15Al0.05O2 Cathode Materials Induced by the Initial Charge , 2014 .

[133]  Masayuki Morita,et al.  Cycling Characteristics of Secondary Li Electrode in LiBF4 / Mixed Ether Electrolytes , 1985 .

[134]  Sunhye Yang,et al.  Thermal stability and performance studies of LiCo1/3Ni1/3Mn1/3O2 with phosphazene additives for Li-ion batteries , 2009 .

[135]  Kai Xie,et al.  Flame Retardant and Stable Li1.5Al0.5Ge1.5(PO4)3-Supported Ionic Liquid Gel Polymer Electrolytes for High Safety Rechargeable Solid-State Lithium Metal Batteries , 2018 .

[136]  B. El-Zahab,et al.  Polymeric Ionic Liquid Gel Electrolyte for Room Temperature Lithium Battery Applications , 2016 .

[137]  Peter Lamp,et al.  Nickel-Rich Layered Cathode Materials for Automotive Lithium-Ion Batteries: Achievements and Perspectives , 2017 .

[138]  Li Ma,et al.  Thermal conductivity enhancement of phase change materials with 3D porous diamond foam for thermal energy storage , 2019, Applied Energy.

[139]  Stefano Passerini,et al.  Ionic Liquid Electrolytes for Safer Lithium Batteries: I. Investigation Around Optimal Formulation , 2016 .

[140]  Kang Xu,et al.  LiBOB: Is it an alternative salt for lithium ion chemistry? , 2005 .

[141]  Robert J. Young,et al.  Deformation mechanisms in crystalline polymers , 1974 .

[142]  Yongqi Li,et al.  The Efficiency of Heptafluoropropane Fire Extinguishing Agent on Suppressing the Lithium Titanate Battery Fire , 2016 .

[143]  Jingwen Weng,et al.  An Experimental Study on the Thermal Failure Propagation in Lithium-Ion Battery Pack , 2018 .

[144]  Jinyue Yan,et al.  Preparation and thermal properties of polyethylene glycol/expanded graphite blends for energy storage , 2009 .

[145]  Jianqiu Li,et al.  Thermal Runaway of Lithium-Ion Batteries without Internal Short Circuit , 2018, Joule.

[146]  Xintian Liu,et al.  Structural optimization of lithium-ion battery for improving thermal performance based on a liquid cooling system , 2019, International Journal of Heat and Mass Transfer.

[147]  Chris Yuan,et al.  In-situ temperature measurement in lithium ion battery by transferable flexible thin film thermocouples , 2014 .

[148]  Pankaj Arora,et al.  Battery separators. , 2004, Chemical reviews.

[149]  Li Li,et al.  Electrochemical performance and thermal property of electrospun PPESK/PVDF/PPESK composite separator for lithium-ion battery , 2013, Journal of Applied Electrochemistry.

[150]  Sung Min Kang,et al.  Mussel- and Diatom-Inspired Silica Coating on Separators Yields Improved Power and Safety in Li-Ion Batteries , 2012 .

[151]  Jing Li,et al.  The reactivity of charged positive Li1-n[NixMnyCoz]O2 electrodes with electrolyte at elevated temperatures using accelerating rate calorimetry , 2018, Journal of Power Sources.

[152]  Myung-Hyun Ryou,et al.  New flame-retardant composite separators based on metal hydroxides for lithium-ion batteries , 2015 .

[153]  K. S. Nanjundaswamy,et al.  Phospho‐olivines as Positive‐Electrode Materials for Rechargeable Lithium Batteries , 1997 .

[154]  V. K. Garg,et al.  Enhancement of electrochemical behavior of nanostructured LiFePO4/Carbon cathode material with excess Li , 2016 .

[155]  J. Dahn,et al.  Accelerating Rate Calorimetry Study on the Thermal Stability of Lithium Intercalated Graphite in Electrolyte. II. Modeling the Results and Predicting Differential Scanning Calorimeter Curves , 1999 .

[156]  Junyao Wang,et al.  Improved thermal performance of a large laminated lithium-ion power battery by reciprocating air flow , 2019, Applied Thermal Engineering.

[157]  Jeom-Soo Kim,et al.  In Situ XRD Investigation and Thermal Properties of Mg Doped LiCoO2 for Lithium Ion Batteries , 2012 .

[158]  Yan Yu,et al.  Progress of enhancing the safety of lithium ion battery from the electrolyte aspect , 2019, Nano Energy.

[159]  Shin Fujitani,et al.  Development of Lithium-Ion Batteries with a LiCoO2 Cathode Toward High Capacity by Elevating Charging Potential , 2008 .

[160]  Roberto Passerone,et al.  Combustible gases and early fire detection: an autonomous system for wireless sensor networks , 2010, e-Energy.

[161]  Jiateng Zhao,et al.  Investigation of power battery thermal management by using mini-channel cold plate , 2015 .

[162]  Min-Joon Lee,et al.  The role of nanoscale-range vanadium treatment in LiNi0.8Co0.15Al0.05O2 cathode materials for Li-ion batteries at elevated temperatures , 2015 .

[163]  Guy Marlair,et al.  Scenario-based prediction of Li-ion batteries fire-induced toxicity , 2016 .

[164]  Ganesan Nagasubramanian.  Comparison of the thermal and electrochemical properties of LiPF6 and LiN(SO2C2F5)2 salts in organic electrolytes , 2003 .

[165]  Jianlin Hu,et al.  A new phosphonamidate as flame retardant additive in electrolytes for lithium ion batteries , 2012 .

[166]  Depeng Kong,et al.  Study of the fire behavior of high-energy lithium-ion batteries with full-scale burning test , 2015 .

[167]  Jürgen Besenhard,et al.  Effect of polysulfide-containing electrolyte on the film formation of the negative electrode , 1997 .

[168]  Chao-Hsin Lin,et al.  Experimental study of n-Heptane pool fire behavior in an altitude chamber , 2013 .

[169]  Yuliang Cao,et al.  Temperature-sensitive cathode materials for safer lithium-ion batteries , 2011 .

[170]  Shilun Ruan,et al.  Electrospun coaxial PPESK/PVDF fibrous membranes with thermal shutdown property used for lithium-ion batteries , 2019, Materials Letters.

[171]  R. Spotnitz,et al.  Abuse behavior of high-power, lithium-ion cells , 2003 .

[172]  Huifang Kang,et al.  The impact of enclosure and boundary conditions with a wedge‐shaped path and air cooling for battery thermal management in electric vehicles , 2018, International Journal of Energy Research.

[173]  Zhengguo Zhang,et al.  A hybrid thermal management system for lithium ion batteries combining phase change materials with forced-air cooling , 2015 .

[174]  S. Neill,et al.  Resource assessment for future generations of tidal-stream energy arrays , 2015 .

[175]  Guang Jia,et al.  Electrical properties of Y- and Mn-doped BaTiO3-based PTC ceramics , 2008 .

[176]  Zhengguo Zhang,et al.  Thermal management performance of phase change materials with different thermal conductivities for Li-ion battery packs operated at low temperatures , 2018 .

[177]  Seung-Hyeon Moon,et al.  Flame retardant coated polyolefin separators for the safety of lithium ion batteries , 2015, Korean Journal of Chemical Engineering.

[178]  Jiajia Yan,et al.  Water cooling based strategy for lithium ion battery pack dynamic cycling for thermal management system , 2018 .

[179]  Jinhua Sun,et al.  The combustion behavior of large scale lithium titanate battery , 2015, Scientific Reports.

[180]  Martin Winter,et al.  Cyclic and acyclic sulfites: new solvents and electrolyte additives for lithium ion batteries with graphitic anodes? , 2001 .

[181]  Yaping He,et al.  Combustion characteristics of n-heptane and wood crib fires at different altitudes , 2009 .

[182]  A Zober,et al.  Intoxication following the inhalation of hydrogen fluoride , 1984, Archives of Toxicology.

[183]  E. Roth,et al.  Simulation of abuse tolerance of lithium-ion battery packs , 2007 .

[184]  Xigao Jian,et al.  Preparation and characterization of electrospun poly(phthalazinone ether nitrile ketone) membrane with novel thermally stable properties , 2015 .

[185]  Gregorio Iglesias,et al.  A review of combined wave and offshore wind energy , 2015 .

[186]  Michael Pecht,et al.  Lessons Learned from the 787 Dreamliner Issue on Lithium-Ion Battery Reliability , 2013 .

[187]  Yi Xie,et al.  Synthesis of hematite (alpha-Fe2O3) nanorods: diameter-size and shape effects on their applications in magnetism, lithium ion battery, and gas sensors. , 2006, The journal of physical chemistry. B.

[188]  M. Wagemaker,et al.  Properties and promises of nanosized insertion materials for Li-ion batteries. , 2013, Accounts of chemical research.

[189]  G. Yushin,et al.  A Major Constituent of Brown Algae for Use in High-Capacity Li-Ion Batteries , 2011, Science.

[190]  Myung-Hyun Ryou,et al.  Mussel‐Inspired Adhesive Binders for High‐Performance Silicon Nanoparticle Anodes in Lithium‐Ion Batteries , 2013, Advanced materials.

[191]  Kim Yeow,et al.  Characterizing Thermal Runaway of Lithium-ion Cells in a Battery System Using Finite Element Analysis Approach , 2013 .

[192]  Junwei Jiang,et al.  ARC studies of the thermal stability of three different cathode materials: LiCoO2; Li[Ni0.1Co0.8Mn0.1]O2; and LiFePO4, in LiPF6 and LiBoB EC/DEC electrolytes , 2004 .

[193]  Z. Zhang,et al.  Differential scanning calorimetry material studies: implications for the safety of lithium-ion cells , 1998 .

[194]  Lili Liu,et al.  Composite of a nonwoven fabric with poly(vinylidene fluoride) as a gel membrane of high safety for lithium ion battery , 2013 .

[195]  Bin Huang,et al.  Synthesis of Mg-doped LiNi0.8Co0.15Al0.05O2 oxide and its electrochemical behavior in high-voltage lithium-ion batteries , 2014 .

[196]  Xuning Feng,et al.  Characterization of penetration induced thermal runaway propagation process within a large format lithium ion battery module , 2015 .

[197]  Vincent A. Hackley,et al.  Effect of Carboxymethyl Cellulose on Aqueous Processing of Natural Graphite Negative Electrodes and their Electrochemical Performance for Lithium Batteries , 2005 .

[198]  Nadarajah Kannan,et al.  Solar energy for future world: - A review , 2016 .

[199]  Yonghuan Ren,et al.  Thermal management of a Li-ion battery pack employing water evaporation , 2017 .

[200]  L. Wang,et al.  A rapid low-temperature internal heating strategy with optimal frequency based on constant polarization voltage for lithium-ion batteries , 2016 .

[201]  T. Ohzuku,et al.  Layered Lithium Insertion Material of LiCo1/3Ni1/3Mn1/3O2 for Lithium-Ion Batteries , 2001 .

[202]  Martin Winter,et al.  Safety Performance of 5 Ah Lithium Ion Battery Cells Containing the Flame Retardant Electrolyte Additive (Phenoxy) Pentafluorocyclotriphosphazene , 2018, Energy Technology.

[203]  Shang Gao,et al.  Thermal Runaway Propagation Assessment of Different Battery Pack Designs Using the TF5 Draft as Framework , 2019, Journal of The Electrochemical Society.

[204]  Hui Wu,et al.  A yolk-shell design for stabilized and scalable li-ion battery alloy anodes. , 2012, Nano letters.

[205]  Guoqing Zhang,et al.  Experimental study of a passive thermal management system for three types of battery using copper foam saturated with phase change materials , 2017 .

[206]  Robert E. Keane,et al.  A classification of landscape fire succession models: spatial simulations of fire and vegetation dynamics , 2004 .

[207]  B. Dunn,et al.  Electrical Energy Storage for the Grid: A Battery of Choices , 2011, Science.

[208]  Ya-Ling He,et al.  Internal cooling of a lithium-ion battery using electrolyte as coolant through microchannels embedded inside the electrodes , 2015 .

[209]  Qingsong Wang,et al.  Thermal runaway caused fire and explosion of lithium ion battery , 2012 .

[210]  Craig B. Arnold,et al.  The Effects of Defects on Localized Plating in Lithium-Ion Batteries , 2015 .

[211]  Peng Wu,et al.  Thermal runaway propagation model for designing a safer battery pack with 25Ah LiNixCoyMnzO2 large format lithium ion battery , 2015 .

[212]  Wei Lu,et al.  Experimental study on the efficiency of dodecafluoro-2-methylpentan-3-one on suppressing lithium-ion battery fires , 2018, RSC advances.

[213]  R. Staniewicz,et al.  Improved low temperature performance of lithium ion cells with quaternary carbonate-based electrolytes , 2003 .

[214]  H. Maleki,et al.  Effects of overdischarge on performance and thermal stability of a Li-ion cell , 2006 .

[215]  Kang Xu,et al.  Effects of Tris(2,2,2-trifluoroethyl) Phosphate as a Flame-Retarding Cosolvent on Physicochemical Properties of Electrolytes of LiPF6 in EC-PC-EMC of 3:3:4 Weight Ratios , 2002 .

[216]  Seung-Don Choi,et al.  The Current Move of Lithium Ion Batteries Towards the Next Phase , 2012 .

[217]  Chi-Yuan Lee,et al.  In Situ Monitoring of Temperature inside Lithium-Ion Batteries by Flexible Micro Temperature Sensors , 2011, Sensors.

[218]  Zhou Xiaodong,et al.  Experiment study of the altitude effects on spontaneous ignition characteristics of wood , 2010 .

[219]  Chun-hua Chen,et al.  Dimethyl methylphosphonate (DMMP) as an efficient flame retardant additive for the lithium-ion battery electrolytes , 2007 .

[220]  Jian Wang,et al.  Experimental study of burning rates of cardboard box fires near sea level and at high altitude , 2013 .

[221]  Philippe Dubois,et al.  New prospects in flame retardant polymer materials: From fundamentals to nanocomposites , 2009 .

[222]  Dongsheng Wen,et al.  Experimental and numerical investigation on integrated thermal management for lithium-ion battery pack with composite phase change materials , 2017 .

[223]  Chi-Min Shu,et al.  Thermal explosion hazards on 18650 lithium ion batteries with a VSP2 adiabatic calorimeter. , 2011, Journal of hazardous materials.

[224]  X. X. Zhang,et al.  Super-cooling prevention of microencapsulated phase change material , 2004 .

[225]  Bo Lu,et al.  Diffusion induced stress in layered Li-ion battery electrode plates , 2012 .

[226]  T. Stuart,et al.  HEV battery heating using AC currents , 2004 .

[227]  Yanfa Yan,et al.  Conformal surface coatings to enable high volume expansion Li-ion anode materials. , 2010, Chemphyschem : a European journal of chemical physics and physical chemistry.

[228]  Jian Wang,et al.  Experimental study on the thermal behaviors of lithium-ion batteries under discharge and overcharge conditions , 2018, Journal of Thermal Analysis and Calorimetry.

[229]  Halime Paksoy,et al.  Improving thermal conductivity phase change materials—A study of paraffin nanomagnetite composites , 2015 .

[230]  Fangming Jiang,et al.  Minimization of thermal non-uniformity in lithium-ion battery pack cooled by channeled liquid flow , 2019, International Journal of Heat and Mass Transfer.

[231]  André Bontemps,et al.  Realization, test and modelling of honeycomb wallboards containing a Phase Change Material , 2011 .

[232]  Christopher J. Orendorff,et al.  The Role of Separators in Lithium-Ion Cell Safety , 2012 .

[233]  Neha Chawla,et al.  Recent Advances in Non-Flammable Electrolytes for Safer Lithium-Ion Batteries , 2019, Batteries.

[234]  Weirong Huo,et al.  Effects of Bi1/2Na1/2TiO3 on the Curie temperature and the PTC effects of BaTiO3-based positive temperature coefficient ceramics , 2006 .

[235]  Ke Li,et al.  Advanced Separators for Lithium-Ion and Lithium-Sulfur Batteries: A Review of Recent Progress. , 2016, ChemSusChem.

[236]  Minggao Ouyang,et al.  A 3D thermal runaway propagation model for a large format lithium ion battery module , 2016 .

[237]  T. Akiyama,et al.  Thermal conductivity enhancement of erythritol phase change material with percolated aluminum filler , 2019, Materials Chemistry and Physics.

[238]  Hartung Wilstermann,et al.  Fire Fighting of Li-Ion Traction Batteries , 2013 .

[239]  Jinhua Sun,et al.  C80 Calorimeter Studies of the Thermal Behavior of LiPF6 Solutions , 2006 .

[240]  Myung-Hyun Ryou,et al.  Effects of lithium salts on thermal stabilities of lithium alkyl carbonates in SEI layer , 2012 .

[241]  Partha P. Mukherjee,et al.  Experimental Analysis of Thermal Runaway and Propagation in Lithium-Ion Battery Modules , 2015 .

[242]  J. Yamaki,et al.  Thermal stability of alkyl carbonate mixed-solvent electrolytes for lithium ion cells , 2002 .

[243]  Hui Wu,et al.  Improving battery safety by early detection of internal shorting with a bifunctional separator , 2014, Nature Communications.

[244]  Sheng Cheng,et al.  A highly concentrated phosphate-based electrolyte for high-safety rechargeable lithium batteries. , 2018, Chemical communications.

[245]  Jeff Dahn,et al.  Comparison of Single Crystal and Polycrystalline LiNi0.5Mn0.3Co0.2O2 Positive Electrode Materials for High Voltage Li-Ion Cells , 2017 .

[246]  Myung-Hyun Ryou,et al.  Excellent Cycle Life of Lithium‐Metal Anodes in Lithium‐Ion Batteries with Mussel‐Inspired Polydopamine‐Coated Separators , 2012 .

[247]  Per Blomqvist,et al.  Characteristics of lithium-ion batteries during fire tests , 2014 .

[248]  Fredrik Larsson,et al.  Thermal Modelling of Cell-to-Cell Fire Propagation and Cascading Thermal Runaway Failure Effects for Lithium-Ion Battery Cells and Modules Using Fire Walls , 2016 .

[249]  John B. Goodenough,et al.  Lithium insertion into manganese spinels , 1983 .

[250]  Myung-Hyun Ryou,et al.  Effect of Al2O3 coatings prepared by RF sputtering on polyethylene separators for high-power lithium ion batteries , 2014, Macromolecular Research.

[251]  Peng Liu,et al.  Preparation of thermally stable composite forward osmosis hollow fiber membranes based on copoly(phthalazinone biphenyl ether sulfone) substrates , 2017 .

[252]  J. Meyer,et al.  Glass transition temperature as a guide to selection of polymers suitable for PTC materials , 1973 .

[253]  Said Al-Hallaj,et al.  Preventing thermal runaway propagation in lithium ion battery packs using a phase change composite material: An experimental study , 2017 .

[254]  Qingsong Wang,et al.  Effects of solvents and salt on the thermal stability of charged LiCoO2 , 2009 .