The Transverse Crack Tension test revisited: An experimental and numerical study

Several problems arise when measuring the mode II interlaminar fracture toughness using a Transverse Crack Tension specimen; in particular, the fracture toughness depends on the geometry of the specimen and cannot be considered a material parameter. A preliminary experimental campaign was conducted on TCTs of different sizes but no fracture toughness was measured because the TCTs failed in an unacceptable way, invalidating the tests. A comprehensive numerical and experimental investigation is conducted to identify the main causes of this behaviour and a modification of the geometry of the specimen is proposed. It is believed that the obtained results represent a significant contribution in the understanding of the TCT test as a mode II characterization procedure and, at the same time, provide new guidelines to characterize the mode II crack propagation under tensile loads.

[1]  Sean S. Teller,et al.  Recommendations for an ASTM Standardized Test for Determining G IIc of Unidirectional Laminated Polymeric Matrix Composites , 2010 .

[2]  P. Camanho,et al.  Measurement of resistance curves in the longitudinal failure of composites using digital image correlation , 2010 .

[3]  P. Camanho,et al.  Numerical Simulation of Mixed-Mode Progressive Delamination in Composite Materials , 2003 .

[4]  R. Prinz,et al.  Characterisation of interlaminar mode I and mode II fracture in CFRP laminates. , 1991 .

[5]  P. Camanho,et al.  Hybrid CFRP/titanium bolted joints: Performance assessment and application to a spacecraft payload adaptor , 2010 .

[6]  Pedro P. Camanho,et al.  Accurate simulation of delamination growth under mixed-mode loading using cohesive elements: Definition of interlaminar strengths and elastic stiffness , 2010 .

[7]  Zhigang Suo,et al.  Orthotropy rescaling and implications for fracture in composites , 1991 .

[8]  M. Wisnom,et al.  An Experimental and Analytical Study of Delamination of Unidirectional Specimens with Cut Central Plies , 1994 .

[9]  Jr. J. Crews,et al.  Mixed-Mode Bending Method for Delamination Testing , 1990 .

[10]  W. Johnston,et al.  Mode II Interlaminar Fracture Toughness and Fatigue Characterization of a Graphite Epoxy Composite Material , 2010 .

[11]  Pedro P. Camanho,et al.  A damage model for the simulation of delamination in advanced composites under variable-mode loading , 2006 .

[12]  G. Pitarresi,et al.  A review of the general theory of thermoelastic stress analysis , 2003 .

[13]  A. K. Wong,et al.  50th Anniversary Article: Seeing Stresses through the Thermoelastic Lens—A Retrospective and Prospective from an Australian Viewpoint , 2015 .

[14]  Zhigang Suo,et al.  The role of material orthotropy in fracture specimens for composites , 1992 .

[15]  Umberto Galietti,et al.  A Quantitative Analysis of the Thermoelastic Effect in CFRP Composite Materials , 2010 .

[16]  Pedro P. Camanho,et al.  Measurement of the compressive crack resistance curve of composites using the size effect law , 2014 .

[17]  Pedro P. Camanho,et al.  An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models , 2007 .

[18]  Ole Thybo Thomsen,et al.  Through Thickness Stress Distributions in Pultruded GRP Materials , 2010 .

[19]  Justin A. Blaber,et al.  Ncorr: Open-Source 2D Digital Image Correlation Matlab Software , 2015, Experimental Mechanics.

[20]  John H. Crews,et al.  The mixed-mode bending method for delamination testing , 1989 .

[21]  Xuekun Sun,et al.  Geometry and Data Reduction Recommendations for a Standardized End Notched Flexure Test for Unidirectional Composites , 2006 .

[23]  P. Cunningham,et al.  A generalised approach to the calibration of orthotropic materials for thermoelastic stress analysis , 2008 .

[24]  Z. Bažant,et al.  Fracture and Size Effect in Concrete and Other Quasibrittle Materials , 1997 .

[25]  A. Mancuso,et al.  Thermo-Mechanical Behaviour of Flax-Fibre Reinforced Epoxy Laminates for Industrial Applications , 2015, Materials.

[26]  Pedro P. Camanho,et al.  Determination of the mode I crack resistance curve of polymer composites using the size-effect law , 2014 .

[27]  Giuseppe Pitarresi,et al.  Lock-In Signal Post-Processing Techniques in Infra-Red Thermography for Materials Structural Evaluation , 2015 .

[28]  Vincenzo Fiore,et al.  A DIC-based study of flexural behaviour of roving/mat/roving pultruded composites , 2015 .

[29]  M. Wisnom.  On the Increase in Fracture Energy with Thickness in Delamination of Unidirectional Glass Fibre-Epoxy with Cut Central Plies , 1992 .

[30]  Ronald Krueger,et al.  The Virtual Crack Closure Technique : History , Approach and Applications , 2002 .

[31]  P. Camanho,et al.  Prediction of size effects in notched laminates using continuum damage mechanics , 2007 .

[32]  D. Tumino,et al.  Interlaminar fracture toughness behavior of electron-beam cured carbon-fiber reinforced epoxy–resin composites , 2014 .

[33]  Pierre Bremond,et al.  Lock-in thermography: a tool to analyze and locate thermomechanical mechanisms in materials and structures , 2001, SPIE Defense + Commercial Sensing.

[34]  P. Linde,et al.  Size effects on the tensile and compressive failure of notched composite laminates , 2013 .

[35]  L. Sluys,et al.  A numerical investigation into the size effect in the transverse crack tension test for mode II delamination , 2013 .

[36]  Barry D. Davidson,et al.  Effects of Friction, Geometry, and Fixture Compliance on the Perceived Toughness from Three-and Four-Point Bend End-Notched Flexure Tests , 2005 .

[37]  Lawrence T. Drzal,et al.  Fibre-matrix adhesion and its relationship to composite mechanical properties , 1993 .

[38]  Barry D. Davidson,et al.  Evaluation of Precracking Methods for the End-Notched Flexure Test , 2007 .

[39]  P. Camanho,et al.  Mixed-Mode Decohesion Finite Elements for the Simulation of Delamination in Composite Materials , 2002 .

[40]  Yiu-Wing Mai,et al.  Crack growth resistance curves in strain-softening materials , 1986 .

[41]  Chiara Colombo,et al.  Static and fatigue characterisation of new basalt fibre reinforced composites , 2012 .

[42]  J. Xavier,et al.  Measurement of the mode II intralaminar fracture toughness and R-curve of polymer composites using a modified Iosipescu specimen and the size effect law , 2015 .