Strength scaling of adhesive joints in polymer–matrix composites

The fracture of adhesive joints between two glass-fibre laminates was studied by testing double cantilever beam test specimens loaded by uneven bending moments. A large-scale fracture process zone, consisting of a crack tip and a fibre bridging zone, developed. The mixed mode fracture resistance increased with increasing crack length, eventually reaching a steady-state level (R-curve behaviour). The steady-state fracture resistance level increased with increasing amount of tangential crack opening displacement. Cohesive laws, obtained from fracture resistance data, were used for prediction the load carrying capacity of 2-m long “medium size” adhesive joint specimens subjected to four point flexure. Medium size specimens were manufactured and tested. A good agreement was found between the predicted and measured strength values of the medium-size specimens. Thus, the scaling from small specimens to medium-size specimens was successfully achieved.

[1]  M. D. Thouless,et al.  Use of a cohesive-zone model to analyze the fracture of a fiber-reinforced polymer-matrix composite , 2005 .

[2]  Pedro P. Camanho,et al.  An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models , 2007 .

[3]  Arne Hillerborg,et al.  Application of the fictitious crack model to different types of materials , 1991, International Journal of Fracture.

[4]  Bent F. Sørensen,et al.  Crack growth in composites Applicability of R-curves and bridging laws , 2000 .

[5]  M. D. Thouless,et al.  Mixed-mode fracture analyses of plastically-deforming adhesive joints , 2001 .

[6]  Zhigang Suo,et al.  Sandwich test specimens for measuring interface crack toughness , 1989 .

[7]  James R. Rice,et al.  Elastic Fracture Mechanics Concepts for Interfacial Cracks , 1988 .

[8]  K. Liechti,et al.  Mixed-mode, time-dependent rubber/metal debonding , 2001 .

[9]  Anthony G. Evans,et al.  The role of fiber bridging in the delamination resistance of fiber-reinforced composites , 1992 .

[10]  J. Dundurs.  Discussion: ``Edge-Bonded Dissimilar Orthogonal Elastic Wedges Under Normal and Shear Loading'' (Bogy, D. B., 1968, ASME J. Appl. Mech., 35, pp. 460-466) , 1969 .

[11]  Zhigang Suo,et al.  Delamination R-curve phenomena due to damage , 1992 .

[12]  Yiu-Wing Mai,et al.  Crack growth resistance curves in strain-softening materials , 1986 .

[13]  Zhigang Suo,et al.  Delamination Specimens for Orthotropic Materials , 1990 .

[14]  Wing Kam Liu,et al.  Nonlinear Finite Elements for Continua and Structures , 2000 .

[15]  A. Kinloch.  Adhesion and Adhesives: Science and Technology , 2010 .

[16]  Bent F. Sørensen,et al.  Mode I intra-laminar crack growth in composites — modelling of R-curves from measured bridging laws , 2001 .

[17]  A. Evans,et al.  Comment on the spalling and edge-cracking of plates , 1990 .

[18]  D. S. Dugdale.  Yielding of steel sheets containing slits , 1960 .

[19]  S. Östlund.  FRACTURE MODELLING OF BRITTLE-MATRIX COMPOSITES WITH SPATIALLY DEPENDENT CRACK BRIDGING , 1995 .

[20]  J. L. Högberg,et al.  Constitutive behaviour of mixed mode loaded adhesive layer , 2007 .

[21]  B. F. Sørensen,et al.  Interface crack in sandwich specimen , 2007 .

[22]  J. Rice.  A path-independent integral and the approximate analysis of strain , 1968 .

[23]  Bent F. Sørensen,et al.  Determination of mixed mode cohesive laws , 2006 .

[24]  Ignace Verpoest,et al.  Interlaminar fracture toughness of CFRP influenced by fibre surface treatment: Part 1. Experimental results , 1995 .

[25]  Bent F. Sørensen,et al.  The influence of fibre sizing on the strength and fracture toughness of glass fibre composites , 2005 .

[26]  M. D. Thouless,et al.  The effects of geometry and material properties on the fracture of single lap-shear joints , 2002 .

[27]  Tove Jacobsen,et al.  Large scale bridging in compos-ites: R-curve and bridging laws , 1998 .

[28]  Z. Suo,et al.  Mixed mode cracking in layered materials , 1991 .

[29]  B. F. Sørensen.  Thermally induced delamination of symmetrically graded multilayers , 2004 .

[30]  A. Kinloch.  Adhesion and adhesives , 1987 .

[31]  Bent F. Sørensen,et al.  DCB-specimen loaded with uneven bending moments , 2006 .

[32]  P. Camanho,et al.  Numerical Simulation of Mixed-Mode Progressive Delamination in Composite Materials , 2003 .

[33]  Brian N. Cox,et al.  The determination of crack bridging forces , 1991, International Journal of Fracture.

[34]  Zhigang Suo,et al.  Remarks on Crack-Bridging Concepts , 1992 .

[35]  P. Olsson,et al.  On the determination of the constitutive properties of thin interphase layers — An exact inverse solution , 1989 .

[36]  A. Waas,et al.  Mixed-mode cohesive-zone models for fracture of an adhesively bonded polymer–matrix composite , 2006 .

[37]  J. Dundurs,et al.  Discussion of Edge-Bonded Dissimilar Orthogonal Elastic Wedges under Normal and Shear Loading , 1969 .

[38]  G. I. Barenblatt.  THE MATHEMATICAL THEORY OF EQUILIBRIUM CRACKS IN BRITTLE FRACTURE , 1962 .

[39]  J. K. Spelt,et al.  Application of a new constant G load-jig to creep crack growth in adhesive joints , 1995 .

[40]  M. D. Thouless,et al.  Numerical simulations of adhesively-bonded beams failing with extensive plastic deformation , 1999 .

[41]  Z. Suo,et al.  Interface crack between two elastic layers , 1990 .

[42]  A. Evans,et al.  A Test Specimen for Determining the Fracture Resistance of Bimaterial Interfaces , 1989 .

[43]  Kenneth M. Liechti,et al.  COHESIVE ZONE MODELING OF CRACK NUCLEATION AT BIMATERIAL CORNERS , 2000 .

[44]  F. L. Matthews.  Joining fibre-reinforced plastics , 1987 .

[45]  Bent F. Sørensen,et al.  Characterizing delamination of fibre composites by mixed mode cohesive laws , 2009 .