Investigation of heat transfer and hydraulic resistance in small-scale pillow-plate heat exchangers

Abstract Pillow-Plate Heat Exchangers (PPHEs) represent an innovative equipment type, with space-effective, light and pressure-resistant construction. In this work, an experimental study of air cooling by water in small-scale PPHEs was carried out and an analysis of the hydraulic resistance and heat transfer was performed based on the experimental data. A semi-empirical correlation for friction factor inside pillow-plate panels which is based on main geometric parameters is proposed. This correlation is reliable in a wide range of Reynolds numbers, both for laminar and turbulent flow regime. For the external channel between pillow-plate panels, the correlations for pressure drop and heat transfer were obtained based on experimental data. The CFD simulations were carried out to investigate heat transfer in the external channel of the PPHE. The deviation between the experimental and simulated values of heat transfer coefficient is maximum 17%. The received correlations enable to calculate the overall heat transfer and pressure drop in small-scale PPHEs and can be applied for preliminary design of PPHEs. The case study of the PPHE application for water heating is considered. The designed heat exchanger with minimal heat transfer area has 30% less surface area then chevron-type plate heat exchangers traditionally used for such application.

[1]  Holger Venzke,et al.  Interpolation Correlations for Fluid Properties of Humid Air in the Temperature Range 100 °C to 200 °C , 1997 .

[2]  Eugeny Y. Kenig,et al.  CFD‐Untersuchung der Fluiddynamik und des Wärmeübergangs bei einphasiger Strömung im welligen Spalt zwischen Thermoblechen , 2015 .

[3]  E. Kenig,et al.  Single-Phase Flow and Condensation in Pillow-Plate Condensers , 2018 .

[4]  Bengt Sundén,et al.  Optimal design of plate heat exchangers with and without pressure drop specifications , 2003 .

[5]  E. Kenig,et al.  An approach for pillow plate heat exchangers design for single-phase applications , 2019, Applied Thermal Engineering.

[6]  M. Bahrami,et al.  Development of novel plate heat exchanger using natural graphite sheet , 2019, International Journal of Heat and Mass Transfer.

[7]  Y. Zhu,et al.  Experimental and numerical investigation on the exergy and entransy performance of a novel plate heat exchanger , 2017 .

[8]  Petro O. Kapustenko,et al.  Generalised semi-empirical correlation for heat transfer in channels of plate heat exchanger , 2014 .

[9]  Q. Bi,et al.  Experimental Performance Comparison of Shell-Side Heat Transfer for Shell-and-Tube Heat Exchangers with Different Helical Baffles , 2016 .

[10]  E. Al-Hajri,et al.  Performance characteristics of a novel shell and tube heat exchanger with shell side interstitial twisted tapes for viscous fluids application , 2018 .

[11]  Kenichi Fujii,et al.  Revised formula for the density of moist air (CIPM-2007) , 2008 .

[12]  M. J. H. Simmons,et al.  hiTRAN® Wire Matrix Inserts in Fouling Applications , 2009 .

[13]  S. Scholl,et al.  Enlarged operation ranges for thermosiphon reboilers using pillow plates , 2015 .

[14]  E. Lemmon,et al.  Viscosity and Thermal Conductivity Equations for Nitrogen, Oxygen, Argon, and Air , 2004 .

[15]  E. Kenig,et al.  New design equations for turbulent forced convection heat transfer and pressure loss in pillow-plate channels , 2017 .

[16]  E. Kenig,et al.  Investigation of pillow-plate condensers for the application in distillation columns , 2015 .

[17]  Jirí Jaromír Klemes,et al.  Compact Heat Exchangers for Energy Transfer Intensification: Low Grade Heat and Fouling Mitigation , 2015 .

[18]  E. Kenig,et al.  Heat transfer and pressure loss in small-scale pillow-plate heat exchangers , 2018 .

[19]  E. Kenig,et al.  A CFD Study of the Thermo-Hydraulic Characteristics of Pillow-Plate Heat Exchangers , 2016 .

[20]  Eugeny Y. Kenig,et al.  Determination of the geometric design parameters of pillow-plate heat exchangers , 2015 .