Wendelstein 7-X Near Real-Time Image Diagnostic System for Plasma-Facing Components Protection

Abstract The Wendelstein 7-X (W7-X) fusion experiment is aimed at proving that the stellarator concept is suitable for a future fusion reactor. Therefore, it is designed for steady-state plasmas of up to 30 min, which means that the thermal control of the plasma-facing components (PFCs) is of vital importance to prevent damage to the device. In this paper an overview of the design of the Near Real-Time Image Diagnostic System (hereinafter called “the System”) for PFCs protection in W7-X is presented. The goal of the System is to monitor the PFCs with high risk of permanent damage due to local overheating during plasma operations and to send alarms to the interlock system. The monitoring of the PFCs is based on thermographic and video cameras, and their video streams are analyzed by means of graphics processing unit–based computer vision techniques to detect the strike line, hot spots, and other thermal events. The video streams and the detected thermal events are displayed online in the control room in the form of a thermal map and permanently stored in the database. In order to determine the emissivity and maximum temperature allowed, a pixel-based correspondence between the image and the observed device part is required. The three-dimensional geometry of W7-X makes the System particularly sensitive to the spatial calibration of the cameras since hot spots can be expected anywhere, and a full segmentation of the field of view is necessary, in contrast to other regions of interest–based systems. A precise registration of the field of view and a correction of the strong lens distortion caused by the wide-angle optical system are then required. During the next operation phase the uncooled graphite divertor units will allow the System to be tested without risk of damaging the divertors in preparation for when water-cooled high-heat-flux divertors will be used.

[1]  S Zoletnik,et al.  Diagnostics development for quasi-steady-state operation of the Wendelstein 7-X stellarator (invited). , 2012, The Review of scientific instruments.

[2]  A. Werner,et al.  Construction of Wendelstein 7-X - Engineering a steady state stellarator , 2009, 2009 23rd IEEE/NPSS Symposium on Fusion Engineering.

[3]  Jörg Schacht,et al.  Real Time Software for the Fusion Experiment WENDELSTEIN 7-X , 2006 .

[4]  H. Greuner,et al.  Experimental results of near real-time protection system for plasma facing components in Wendelstein 7-X at GLADIS , 2017 .

[5]  J. Tretter,et al.  Design and technological solutions for the plasma facing components of WENDELSTEIN 7-X , 2011 .

[6]  T. Szabolics,et al.  Overview video diagnostics for the W7-X stellarator , 2015 .

[7]  Zhengyou Zhang,et al.  A Flexible New Technique for Camera Calibration , 2000, IEEE Trans. Pattern Anal. Mach. Intell..

[8]  T. Szepesi,et al.  EDICAM (Event Detection Intelligent Camera) , 2013 .

[9]  V. Moncada,et al.  Integrated software for imaging data analysis applied to edge plasma physic and operational safety , 2011 .

[10]  T. Szabolics,et al.  Software development for the simultaneous control of ten intelligent overview video cameras at W7-X , 2017 .

[11]  Vincent Martin,et al.  Thermal Event Recognition Applied to Protection of Tokamak Plasma-Facing Components , 2010, IEEE Transactions on Instrumentation and Measurement.

[12]  Christoph Biedermann,et al.  Development of infrared and visible endoscope as the safety diagnostic for steady-state operation of Wendelstein 7-X , 2014 .

[13]  G A Wurden,et al.  Detecting divertor damage during steady state operation of Wendelstein 7-X from thermographic measurements. , 2016, The Review of scientific instruments.

[14]  M. Krychowiak,et al.  Design and manufacturing progress of IRVIS endoscopes prototypes for W7-X divertor temperature monitoring , 2016 .

[15]  T. Szabolics,et al.  Event Detection Intelligent Camera: Demonstration of flexible, real-time data taking and processing , 2015 .