Skin friction reduction by large air bubbles in a horizontal channel flow

Abstract Microbubble and air film methods are believed to be applicable to skin friction reduction in ships. Small bubbles are dispersed into the turbulent boundary layer in the former case, and wide air layers cover the wall surface in the latter case. Previous studies did not specifically address the intermediate case between the microbubble and air film conditions. This study is concerned with the possibility and mechanism of drag reduction using relatively large air bubbles compared to the boundary layer thickness in a horizontal turbulent channel flow. The relationship between local skin friction and the bubble’s interfacial structure is investigated by synchronizing the measurement of wall-shear stress with the image acquisition of bubbles. The bubble sizes range from 2 to 90 mm approximately. As a result, a negative correlation between the local skin friction and the local void fraction is confirmed by the time-resolved measurement. A new observation is the fact that the local skin friction decreases drastically in the rear part of individual large bubbles, and rapidly increases after the bubble’s rear interface passes. This characteristic underlies the bubble-size dependency of the average skin friction in the intermediate bubble size condition.

[1]  Toru Iwasaki,et al.  Frictional drag reduction with air lubricant over a super-water-repellent surface , 2000 .

[2]  Y. Kodama,et al.  EXPERIMENTAL STUDY ON MICROBUBBLES AND THEIR APPLICABILITY TO SHIPS FOR SKIN FRICTION REDUCTION , 2000, Proceeding of First Symposium on Turbulence and Shear Flow Phenomena.

[3]  Marc Perlin,et al.  Bubble-size distributions produced by wall injection of air into flowing freshwater, saltwater and surfactant solutions , 2004 .

[4]  Yasushi Takeda,et al.  Turbulent shear stress profiles in a bubbly channel flow assessed by particle tracking velocimetry , 2006 .

[5]  Diffusion of spherical bubbles in a turbulent boundary layer , 2002 .

[6]  Koichi Hishida,et al.  Flow structure of microbubble-laden turbulent channel flow measured by PIV combined with the shadow image technique , 2005 .

[7]  George Em Karniadakis,et al.  Numerical simulation of turbulent drag reduction using micro-bubbles , 2002, Journal of Fluid Mechanics.

[8]  Jean-Louis Marié,et al.  A simple analytical formulation for microbubble drag reduction , 1987 .

[9]  Y. Okamoto,et al.  A Study of Air Lubrication Method to Reduce Frictional Resistance of Ship : Experimental Investigation by Tanker Form Model Ship and Estimation , 2003 .

[10]  Hiroharu Kato,et al.  Effect of microbubbles on the structure of turbulence in a turbulent boundary layer , 1999 .

[11]  R. Latorre,et al.  Micro-bubble resistance reduction on a model SES catamaran , 2003 .

[12]  Steven Deutsch,et al.  Measurements of local skin friction in a microbubble-modified turbulent boundary layer , 1985, Journal of Fluid Mechanics.

[13]  C. Colin,et al.  Experimental study of bubble injection in a turbulent boundary layer , 2002 .

[14]  Hartmut H. Legner,et al.  A simple model for gas bubble drag reduction , 1984 .

[15]  S. Elghobashi,et al.  On the physical mechanisms of drag reduction in a spatially developing turbulent boundary layer laden with microbubbles , 2004, Journal of Fluid Mechanics.

[16]  F. Aloui,et al.  Analysis of wall shear stress in wet foam flows using the electrochemical method , 2003 .

[17]  Rameswar Bhattacharyya,et al.  DRAG REDUCTION OF A SUBMERSIBLE HULL BY ELECTROLYSIS , 1973 .

[18]  Yasuhiro Moriguchi,et al.  Influence of microbubble diameter and distribution on frictional resistance reduction , 2002 .

[19]  Steven Deutsch,et al.  Microbubble drag reduction in liquid turbulent boundary layers , 1992 .