Estimation of the Transient Heat Transfer Rate at the Boundary of an Electronic Chip Packaging

In this study, an inverse algorithm based on the conjugate gradient method and the discrepancy principle is applied to estimate the unknown time-dependent heat transfer rate at the electronic-packaging/heat-sink-assembly interface from the knowledge of temperature measurements taken within the packaging. The temperature data obtained from the direct problem are used to simulate the temperature measurements, and the effect of the errors in these measurements upon the precision of the estimated results is also considered. Results show that an excellent estimation on the time-dependent heat transfer rate can be obtained for the test case considered here.

[1]  Tomasz Zawada,et al.  Simultaneous estimation of heat transfer coefficient and thermal conductivity with application to microelectronic materials , 2006, Microelectron. J..

[2]  Tsung-Chien Chen,et al.  Input Estimation Method in the Use of Electronic Device Temperature Prediction and Heat Flux Inverse Estimation , 2007 .

[3]  Wei Wu,et al.  Filling of nano-via holes by laser-assisted direct imprint , 2006 .

[4]  O. Alifanov.  Inverse heat transfer problems , 1994 .

[5]  Gui-Rong Liu,et al.  Coefficients identification in electronic system cooling simulation through genetic algorithm , 2002 .

[6]  C. L. Niliot,et al.  MULTIPLE TRANSIENT POINT HEAT SOURCES IDENTIFICATION IN HEAT DIFFUSION: APPLICATION TO NUMERICAL TWO- AND THREE-DIMENSIONAL PROBLEMS , 2001 .

[7]  Parametric Investigation of Laser-Assisted Direct Imprint (LADI) Technique , 2006 .

[8]  Kai-Shing Yang,et al.  On the heat transfer characteristics of heat sinks: Influence of fin spacing at low Reynolds number region , 2007 .

[9]  A GENERAL SPACE MARCHING ALGORITHM FOR THE SOLUTION OF TWO-DIMENSIONAL BOUNDARY INVERSE HEAT CONDUCTION PROBLEMS , 1998 .

[10]  Haw Long Lee,et al.  Inverse problem in determining convection heat transfer coefficient of an annular fin , 2007 .

[11]  Y. Joshi,et al.  Single-phase liquid cooled microchannel heat sink for electronic packages , 2005 .

[12]  O. M. Alifanov,et al.  Regularized numerical solution of nonlinear inverse heat-conduction problem , 1975 .

[13]  Fue-Sang Lien,et al.  A MULTIBLOCK IMPLEMENTATION OF A NON‐ORTHOGONAL, COLLOCATED FINITE VOLUME ALGORITHM FOR COMPLEX TURBULENT FLOWS , 1996 .

[14]  A. Tseng,et al.  MULTIDIMENSIONAL INVERSE TRANSIENT HEAT CONDUCTION PROBLEMS BY DIRECT SENSITIVITY COEFFICIENT METHOD USING A FINITE-ELEMENT SCHEME , 1996 .

[15]  Thermally induced optical effects in optical fibers by inverse methodology , 2004 .

[16]  Application of the regularization principle to the formulation of approximate solutions of inverse heat-conduction problems , 1972 .

[17]  H. Park,et al.  On the solution of inverse heat transfer problem using the Karhunen–Loève Galerkin method , 1999 .

[18]  N. V. Kerov,et al.  Determination of external thermal load parameters by solving the two-dimensional inverse heat-conduction problem , 1981 .

[19]  Keith A. Woodbury,et al.  GENETIC ALGORITHM IN SOLUTION OF INVERSE HEAT CONDUCTION PROBLEMS , 1995 .

[20]  Experimental investigation of thermal characteristics for a microchannel heat sink subject to an impinging jet, using a micro-thermal sensor array , 2003 .

[21]  C. Ji,et al.  Experimental investigation in inverse heat conduction problem , 1998 .

[22]  T. Fang,et al.  Modelling of thermal conductance during microthermal machining with scanning thermal microscope using an inverse methodology , 2008 .

[23]  Yu-Ching Yang.  Simultaneously estimating the contact heat and mass transfer coefficients in a double-layer hollow cylinder with interface resistance , 2007 .

[24]  Yogendra Joshi,et al.  Heat transfer enhancement from enclosed discrete components using pin-fin heat sinks , 2002 .

[25]  A simple electron-beam lithography system. , 2005, Ultramicroscopy.