Das anomale Fließverhalten von Polyäthylen hoher Dichte

[1]  E. Uhland.  Stratified two‐phase flog of molten polymers in circular dies , 1977 .

[2]  R. A. Worth,et al.  Wall slip and its implications in the design of single screw melt‐fed extruders , 1977 .

[3]  M. Denn,et al.  Instabilities in polymer processing , 1976 .

[4]  G. Mennig.  Visuelle Untersuchungen zum Wandgleitverhalten hochpolymerer Schmelzen , 1976 .

[5]  E. Uhland.  Modell zur Beschreibung des Fließens wandgleitender Substanzen durch Düsen , 1976 .

[6]  H. Giesekus.  Normblatt DIN 13342: Nicht-newtonsche Flüssigkeiten; Begriffe, Stoffgesetze — Anmerkungen und Erläuterungen , 1975 .

[7]  M. H. Wagner,et al.  Developing flow in circular conduits: transition from plug flow to tube flow , 1975, Journal of Fluid Mechanics.

[8]  J. Otter.  Rheological measurements on two uncrosslinked, unfilled synthetic rubbers , 1975 .

[9]  S. Richardson,et al.  On the no-slip boundary condition , 1973, Journal of Fluid Mechanics.

[10]  H. Hürlimann,et al.  Der Zusammenhang zwischen der Dehnspannung von Kunststoffschmelzen im Düseneinlauf und im Schmelzbruch , 1972 .

[11]  J. Otter.  Some investigations of melt fracture , 1971 .

[12]  Y. Yamaguchi,et al.  Irregular Flow Behaviors of Polymer Melts , 1971 .

[13]  Lee L. Blyler,et al.  Capillary flow instability of ethylene polymer melts , 1970 .

[14]  James L White,et al.  An experimental study of flow patterns in polymer fluids in the reservoir of a capillary rheometer , 1970 .

[15]  W. Philippoff,et al.  Measurement of the Axial Pressure Distribution of Molten Polymers in Flow Through a Circular Tube , 1969 .

[16]  H. Giesekus.  Verschiedene Phänomene in Strömungen viskoelastischer Flüssigkeiten durch Düsen , 1969 .

[17]  James L White,et al.  Extrusion of Polymer Melts and Melt Flow Instabilities. I. Experimental Study of Capillary Flow and Extrudate Distortion , 1969 .

[18]  J. Tordella.  UNSTABLE FLOW OF MOLTEN POLYMERS , 1969 .

[19]  H. Giesekus.  Nicht-lineare Effekte beim Strömen viskoelastischer Flüssigkeiten durch Schlitz- und Lochdüsen , 1968 .

[20]  B. Martin.  Some analytical solutions for viscometric flows of power-law fluids with heat generation and temperature dependent viscosity , 1967 .

[21]  J. Schijf,et al.  The velocity profiles of molten polymers during laminar flow , 1967 .

[22]  C. Gogos,et al.  Velocity profiles of the exit region of molten polyethylene extrudates , 1966 .

[23]  R. F. Westover.  The significance of slip of polymer melt flow , 1966 .

[24]  O. Bartos̆.  A note on the discontinuity in flow curves of molten polyethylene , 1965 .

[25]  A. P. Metzger,et al.  Extrudate swelling at high shear rates , 1965 .

[26]  A. B. Metzner,et al.  Flow behavior of viscoelastic fluids in the inlet region of a channel , 1965 .

[27]  J. Lupton,et al.  Melt flow of polyethylene at high rates , 1965 .

[28]  J. R. Knox,et al.  The Effect of Pressure Losses in the Barrel on Capillary Flow Measurements , 1965 .

[29]  H. Murakami,et al.  Study of flow properties of polymer melt with the screw extruder , 1964 .

[30]  J. White.  Dynamics of viscoelastic fluids, melt fracture, and the rheology of fiber spinning , 1964 .

[31]  Y. Mori,et al.  Discontinuous Flow Properties of High-Density Polyethylene Caused by Slippage Flow , 1964 .

[32]  J. Tordella.  Unstable flow of molten polymers: A second site of melt fracture , 1963 .

[33]  Bryce Maxwell,et al.  Velocity profiles for polyethylene melt in tubes , 1962 .

[34]  M. Mullier,et al.  On the discontinuity in the flow curve of polyethylene , 1962 .

[35]  E. B. Bagley,et al.  Effect of Die Entry Geometry on Polymer Melt Fracture and Extrudate Distortion , 1961 .

[36]  E. B. Bagley,et al.  Flow of Polyethylene into a Capillary , 1960 .

[37]  A. B. Metzner.  Fracture of Non-Newtonian Fluids at High Shear Stresses , 1958 .

[38]  E. B. Bagley,et al.  Discontinuity in the Flow Curve of Polyethylene , 1958 .

[39]  J. Tordella.  Capillary Flow of Molten Polyethylene—A Photographic Study of Melt Fracture , 1957 .

[40]  J. Tordella.  Fracture in the Extrusion of Amorphous Polymers through Capillaries , 1956 .

[41]  H. Nason.  A High Temperature, High Pressure Rheometer for Plastics , 1945 .

[42]  M. Mooney.  Explicit Formulas for Slip and Fluidity , 1931 .

[43]  B. Rabinowitsch,et al.  Über die Viskosität und Elastizität von Solen , 1929 .

[44]  G. W. Blair,et al.  The Influence of the Proximity of a Solid Wall on the Consistency of Viscous and Plastic Materials. III , 1929 .