Pressures on the lining of a large shield tunnel with a small overburden: A case study

Abstract The pressure on a tunnel lining is an important issue in shield tunnel design, because it is related to the safety and durability of the lining. There is an increasing need for short (about 1 km) but wide traffic tunnels in parts of China near rivers. In order to satisfy the gradient requirement of the road over such a short distance, the depth of the overburden is inevitably very shallow. The non-uniform distribution of the pressure on the lining of this kind of tunnel may result in damage to the tunnel segments. However, little published research is available on this topic. In this study, in-situ monitoring was carried out to measure the pressure on the lining of a large cross-river shield tunnel (diameter D = 11.36 m) with a shallow overburden (0.7 D) in silty-sandy ground. A pad type earth pressure gauges and pore-water pressure gauges were used to measure the pressures on the tunnel lining, including the tail brush pressure, grouting pressure, earth pressure and pore-water pressure. The time history and the distribution of pressures on the lining during tunnel construction and post-construction were obtained. A comparison between the measured values and theoretical values was carried out. This showed that the tail brush pressure had a considerable effect on the segments while the shield machine was passing through. Non-uniform tail brush pressures caused cracking and water leakage in the concrete segments. The maximum pressure induced by the backfill grouting was twice that of the theoretical earth pressure. However, the non-uniformity of the backfill grouting induced pressure was not as great as that induced by the tail brushes. In the silty-sandy ground, the earth pressures were generally stable 24 h after segment assembly. The final stable values were close to the total overburden pressure, particularly at the tunnel crown. The pore-water pressure generally was equal to the hydrostatic pressure and accounts for a large proportion of the total earth pressure.

[1]  Hehua Zhu,et al.  Lessons learnt from unusual ground settlement during Double-O-Tube tunnelling in soft ground , 2015 .

[2]  Georg Anagnostou,et al.  Squeezing loading of segmental linings and the effect of backfilling , 2011 .

[3]  Martin Ziegler,et al.  Investigation on influence of tail void grouting on the surface settlements during shield tunneling using a stress-pore pressure coupled analysis , 2014 .

[4]  T Hashimoto,et al.  Simultaneous backfill grouting, pressure development in construction phase and in the long-term , 2004 .

[5]  Jun Sheng Chen,et al.  Numerical study on crack problems in segments of shield tunnel using finite element method , 2009 .

[6]  H. Mashimo,et al.  EVALUATION OF THE LOAD ON SHIELD TUNNEL LINING IN GRAVEL , 2003 .

[7]  Mitsutaka Sugimoto,et al.  Theoretical Model of Shield Behavior During Excavation. II: Application , 2002 .

[8]  Mitsutaka Sugimoto,et al.  Theoretical Model of Shield Behavior During Excavation. I: Theory , 2002 .

[9]  Jun-sheng Chen,et al.  Mechanical behavior of segment rebar of shield tunnel in construction stage , 2008 .

[10]  Jian-Hua Wang,et al.  In situ monitoring of frost heave pressure during cross passage construction using ground-freezing method , 2016 .

[11]  Masayuki Saito,et al.  Study on construction loads during shield tunneling using a three-dimensional FEM model , 2006 .

[12]  Mingfeng Lei,et al.  Calculation of the surrounding rock pressure on a shallow buried tunnel using linear and nonlinear failure criteria , 2014 .

[13]  M. Meguid,et al.  An experimental study of the effect of local contact loss on the earth pressure distribution on existing tunnel linings , 2011 .

[14]  K. J. Bakker,et al.  Ten years of bored tunnels in the Netherlands: Part II: Structural issues , 2008 .

[15]  Adam Bezuijen,et al.  FIELD MEASUREMENTS OF GROUT PRESSURES DURING TUNNELLING OF THE SOPHIA RAIL TUNNEL , 2004 .

[16]  David M. Potts,et al.  Stability of a shallow circular tunnel in cohesionless soil , 1977 .

[17]  Emilio Bilotta,et al.  Internal Forces Arising in the Segmental Lining of an Earth Pressure Balance-Bored Tunnel , 2013 .

[18]  O. Kusakabe,et al.  Shield Tunnel Construction in Centrifuge , 1999 .

[19]  H. Mashimo,et al.  Numerical modelling of the behavior of shield tunnel lining during assembly of a tunnel ring , 2006 .

[20]  J. Nagaya,et al.  Study on earth pressure acting upon shield tunnel lining in clayey and sandy grounds based on field monitoring , 2008 .

[21]  Jun Sheng Chen,et al.  Study on inner force and dislocation of segments caused by shield machine attitude , 2008 .

[22]  Yukinori Koyama,et al.  Present status and technology of shield tunneling method in Japan , 2003 .

[23]  S. Shen,et al.  Leaking behavior of shield tunnels under the Huangpu River of Shanghai with induced hazards , 2013, Natural Hazards.

[24]  H. J. Kim,et al.  Prediction of tunnel lining loads using correction factors , 2006 .

[25]  Shiming Wu,et al.  Design of shield tunnel lining taking fluctuations of river stage into account , 2015 .