Fabrication of Vacuum-Sealed Capacitive Micromachined Ultrasonic Transducer Arrays Using Glass Reflow Process

This paper presents a process for the fabrication of vacuum-sealed capacitive micromachined ultrasonic transducer (CMUT) arrays using glass reflow and anodic bonding techniques. Silicon through-wafer interconnects have been investigated by the glass reflow process. Then, the patterned silicon-glass reflow wafer is anodically bonded to an SOI (silicon-on-insulator) wafer for the fabrication of CMUT devices. The CMUT 5 × 5 array has been successfully fabricated. The resonant frequency of the CMUT array with a one-cell radius of 100 µm and sensing gap of 3.2 µm (distance between top and bottom electrodes) is observed at 2.84 MHz. The Q factor is approximately 1300 at pressure of 0.01 Pa.

[1]  S. Beeby,et al.  MEMS Mechanical Sensors , 2004 .

[2]  Aditi,et al.  Fabrication of Capacitive Micromachined Ultrasonic Transducer Arrays With Isolation Trenches Using Anodic Wafer Bonding , 2015, IEEE Sensors Journal.

[3]  Edward Hæggström,et al.  Fabricating capacitive micromachined ultrasonic transducers with wafer-bonding technology , 2003 .

[4]  Omer Oralkan,et al.  Capacitive micromachined ultrasonic transducers for medical imaging and therapy , 2011, Journal of micromechanics and microengineering : structures, devices, and systems.

[5]  B.T. Khuri-Yakub,et al.  Analytically calculating membrane displacement and the equivalent circuit model of a circular CMUT cell , 2008, 2008 IEEE Ultrasonics Symposium.

[6]  Alessandro Stuart Savoia,et al.  PECVD low stress silicon nitride analysis and optimization for the fabrication of CMUT devices , 2014 .

[7]  B. Khuri-Yakub,et al.  Surface micromachined capacitive ultrasonic transducers , 1998, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[8]  Yongtaek Hong,et al.  Fabrication of high aspect ratio insulating nozzle using glass reflow process and its electrohydrodynamic printing characteristics , 2014, 2014 IEEE 27th International Conference on Micro Electro Mechanical Systems (MEMS).

[9]  O. Oralkan,et al.  Highly sensitive detection of DMMP using a CMUT-based chemical sensor , 2010, 2010 IEEE Sensors.

[10]  Kensall D. Wise,et al.  A Glass-in-Silicon Reflow Process for Three-Dimensional Microsystems , 2013, Journal of Microelectromechanical Systems.

[11]  James J. Allen.  Micro Electro Mechanical System Design , 2005 .

[12]  Shailendra Kumar Tiwari,et al.  Circular Capacitance Micromachined Ultrasonic Transducer , 2009 .

[13]  F. Ayazi,et al.  Temperature compensation of silicon micromechanical resonators via degenerate doping , 2009, 2009 IEEE International Electron Devices Meeting (IEDM).

[14]  Jingkuang Chen,et al.  A Miniature Capacitive Micromachined Ultrasonic Transducer Array for Minimally Invasive Photoacoustic Imaging , 2010, Journal of Microelectromechanical Systems.

[15]  Nguyen Van Toan,et al.  Glass capillaries based on a glass reflow into nano-trench for controlling light transmission , 2016 .

[16]  Butrus T. Khuri-Yakub,et al.  Capacitive Micromachined Ultrasonic Transducers: Theory and Technology , 2003 .

[17]  Nguyen Van Toan,et al.  An Investigation of Processes for Glass Micromachining , 2016, Micromachines.