The limitation of the currently available thermal management method has put an ever serious challenge for computer chip designers. A liquid metal with low melting point around room temperature was recently identified as a powerful coolant of driving heat away because of its superior thermo-physical properties and the unique ability to be driven efficiently by a completely silent electromagnetic pump. However, the adoption of gallium, one of the best candidates as metal coolant so far, may cause serious corrosion to the structure materials and subsequently affect the performance or even dangerous running of the cooling system. To address this emerging critical issue, here the compatibility of gallium with four typical metal substrates (6063 Aluminum-Alloy, T2 Copper-Alloy, Anodic Coloring 6063 Aluminum-Alloy and 1Cr18Ni9 Stainless Steel) was comprehensively investigated in order to better understand the corrosion mechanisms and help find out the most suitable structure material for making a liquid metal cooling device. To grasp in detail the dynamic corrosion behavior, an image acquisition and contrasting method was developed. Moreover, corrosion morphology analyses were performed by means of scanning electron microscope (SEM). The chemical compositions of the corroded layers were evaluated using energy dispersive spectrometry (EDS). According to the experiments, it was found that, the corrosion of the 6063 Aluminum-Alloy was rather evident and serious under the temperature range for chip cooling. The loose corrosion product will not only have no protection for the inner substrate, but also accelerate the corrosion process. Compared to the 6063 Aluminum-Alloy, T2 Copper-Alloy showed a slow and general corrosion, but part of the corrosion product can shed from the substrate, which will accelerate corrosion action and may block the flowing channel. Anodic Coloring 6063 Aluminum-Alloy and 1Cr18Ni9 Stainless Steel were found to have excellent corrosion resistance among these four specimens. No evident corrosion phenomena were found under the examination of SEM and EDS when exposed for 30 days at the temperature of 60°C, which suggests their suitability as structure materials for the flow of liquid metal. However, as for the Anodic Coloring 6063 Aluminum-Alloy, surface treatment and protection are of vital importance. The present study is of significance for making a liquid metal chip cooling device which can actually be used in the future computer industry.
[1]
U. Ghoshal,et al.
Cooling of high-power-density microdevices using liquid metal coolants
,
2004
.
[2]
Tzu-Chen Hung,et al.
An optimal parametric design to improve chip cooling
,
2007
.
[3]
M.J. Ellsworth,et al.
Review of cooling technologies for computer products
,
2004,
IEEE Transactions on Device and Materials Reliability.
[4]
Ali Shakouri,et al.
Nanoscale Thermal Transport and Microrefrigerators on a Chip
,
2006,
Proceedings of the IEEE.
[5]
R. Singh,et al.
Miniature Loop Heat Pipe With Flat Evaporator for Cooling Computer CPU
,
2007,
IEEE Transactions on Components and Packaging Technologies.
[6]
Peng Wang,et al.
On-chip hot spot cooling using silicon thermoelectric microcoolers
,
2007
.
[7]
Krisztian Kordas,et al.
Chip cooling with integrated carbon nanotube microfin architectures
,
2007
.
[8]
R. L. Webb,et al.
Heat rejection limits of air cooled plane fin heat sinks for computer cooling
,
2003
.
[9]
K. Narh,et al.
The effect of liquid gallium on the strengths of stainless steel and thermoplastics
,
1998
.
[10]
W. Q. Tao,et al.
An experimental investigation on a novel high-performance integrated heat pipe–heat sink for high-flux chip cooling
,
2008
.
[11]
Liu Jing,et al.
Liquid metal cooling in thermal management of computer chips
,
2007
.
[12]
Jing Liu,et al.
Heat-driven liquid metal cooling device for the thermal management of a computer chip
,
2007
.