An experimental and coupled thermo-mechanical finite element study of heat partition effects in machining

A better understanding of heat partition between the tool and the chip is required in order to produce more realistic finite element (FE) models of machining processes. The objectives are to use these FE models to optimise the cutting process for longer tool life and better surface integrity. In this work, orthogonal cutting of AISI/SAE 4140 steel was performed with tungsten-based cemented carbide cutting inserts at cutting speeds ranging between 100 and 628 m/min with a feed rate of 0.1 mm/rev and a constant depth of cut of 2.5 mm. Cutting temperatures were measured experimentally using an infrared thermal imaging camera. Chip formation was simulated using a fully coupled thermo-mechanical finite element model. The results from cutting tests were used to validate the model in terms of deformed chip thickness and cutting forces. The coupled thermo-mechanical model was then utilised to evaluate the sensitivity of the model output to the specified value of heat partition. The results clearly show that over a wide range of cutting speeds, the accuracy of finite element model output such as chip morphology, tool–chip interface temperature, von Mises stresses and the tool–chip contact length are significantly dependent on the specified value of heat partition.

[1]  Tuğrul Özel,et al.  Predictive Analytical and Thermal Modeling of Orthogonal Cutting Process—Part I: Predictions of Tool Forces, Stresses, and Temperature Distributions , 2006 .

[2]  Albert J. Shih.  Finite element analysis of orthogonal metal cutting mechanics , 1996 .

[3]  E.J.A. Armarego,et al.  Tool-chip contact length in orthogonal machining and its importance in tool temperature predictions , 1992 .

[4]  British Iron,et al.  The mechanical and physical properties of the British Standard En steels (B.S. 970-1955) , 1964 .

[5]  A. S. Branis,et al.  Finite element simulation of chip formation in orthogonal metal cutting , 2001 .

[6]  Jing Shi,et al.  On Predicting Softening Effects in Hard Turned Surfaces—Part II: Finite Element Modeling and Verification , 2005 .

[7]  Pierre Joyot,et al.  Arbitrary Lagrangian-Eulerian thermomechanical finite-element model of material cutting , 1993 .

[8]  G. Boothroyd.  Temperatures in Orthogonal Metal Cutting , 1963 .

[9]  Matthew A. Davies,et al.  On the measurement and prediction of temperature fields In machining AISI 1045 steel , 2003 .

[10]  Wit Grzesik,et al.  A computational approach to evaluate temperature and heat partition in machining with multilayer coated tools , 2003 .

[11]  Tao Sun,et al.  Finite element optimization of diamond tool geometry and cutting-process parameters based on surface residual stresses , 2007 .

[12]  Xiaomin Deng,et al.  Residual stresses and strains in orthogonal metal cutting , 2003 .

[13]  Pedro J. Arrazola,et al.  A new approach for the friction identification during machining through the use of finite element modeling , 2008 .

[14]  J. Sutherland,et al.  Finite element simulation of the orthogonal metal cutting process for qualitative understanding of the effects of crater wear on the chip formation process , 2002 .

[15]  B. Lindström,et al.  The role of tool-chip contact length in metal cutting , 1993 .

[16]  Mohamed A. Elbestawi,et al.  Modelling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L , 2007 .

[17]  David K. Aspinwall,et al.  Developments in modelling of metal cutting processes , 2007 .

[18]  Xiaomin Deng,et al.  Finite element simulation of high-pressure water-jet assisted metal cutting , 2003 .

[19]  Paul Mativenga,et al.  Investigation of heat partition in high speed turning of high strength alloy steel , 2005 .

[20]  Akhtar S. Khan,et al.  A critical review of experimental results and constitutive models for BCC and FCC metals over a wide range of strain rates and temperatures , 1999 .

[21]  Hossam A. Kishawy,et al.  Arbitrary Lagrangian Eulerian analysis on cutting with a honed tool , 2008 .

[22]  David K. Aspinwall,et al.  Modelling of temperature and forces when orthogonally machining hardened steel , 1999 .

[23]  Xiaomin Deng,et al.  Finite Element Analysis of the Orthogonal Metal Cutting Process , 2000 .

[24]  M. E. Merchant.  Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and a Type 2 Chip , 1945 .

[25]  Patrick Kwon,et al.  An inverse estimation scheme to measure steady-state tool–chip interface temperatures using an infrared camera , 2001 .

[26]  Fabrizio Micari,et al.  Measurement of temperature distribution within tool in metal cutting. Experimental tests and numerical analysis , 1989 .

[27]  Tarek Mabrouki,et al.  Experimental and numerical study of chip formation during straight turning of hardened AISI 4340 steel , 2005 .

[28]  Pierre Joyot,et al.  A numerical simulation of steady state metal cutting , 1998 .

[29]  I. Jawahir,et al.  Progressive tool-wear in machining with coated grooved tools and its correlation with cutting temperature , 2005 .

[30]  Pedro J. Arrazola,et al.  SERRATED CHIP PREDICTION IN FINITE ELEMENT MODELING OF THE CHIP FORMATION PROCESS , 2007 .

[31]  Albert J. Shih,et al.  Finite Element Simulation of Orthogonal Metal Cutting , 1995 .

[32]  Paul Mativenga,et al.  An evaluation of heat partition in the high-speed turning of AISI/SAE 4140 steel with uncoated and TiN-coated tools , 2008 .

[33]  Matthew A. Davies,et al.  High Bandwidth Thermal Microscopy of Machining AISI 1045 Steel , 2005 .

[34]  D. Umbrello,et al.  Experimental and numerical modelling of the residual stresses induced in orthogonal cutting of AISI 316L steel , 2006 .

[35]  Toshio Sata,et al.  Improvement in the working accuracy of an nc lathe by compensating for thermal expansion , 1982 .

[36]  G. R. Johnson,et al.  Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures , 1985 .

[37]  I. Green,et al.  A Finite Element Study of the Residual Stress and Deformation in Hemispherical Contacts , 2005 .

[38]  Fabrizio Micari,et al.  On the FE codes capability for tool temperature calculation in machining processes , 2006 .

[39]  Reginaldo Teixeira Coelho,et al.  Tool wear when turning hardened AISI 4340 with coated PCBN tools using finishing cutting conditions , 2007 .

[40]  David K. Aspinwall,et al.  Modelling of hard part machining , 2002 .

[41]  C. Richard Liu,et al.  The Influence of Material Models on Finite Element Simulation of Machining , 2004 .

[42]  C. Liu,et al.  Finite element analysis of the effect of sequential cuts and tool-chip friction on residual stresses in a machined layer , 2000 .

[43]  G. Byrne,et al.  The mechanisms of chip formation in machining hardened steels , 2002 .

[44]  T. I. El-Wardany,et al.  PHYSICS-BASED SIMULATION OF HIGH SPEED MACHINING , 2002 .

[45]  Yuebin Guo,et al.  A FEM study on mechanisms of discontinuous chip formation in hard machining , 2004 .

[46]  Erol Zeren,et al.  FINITE ELEMENT MODELING OF STRESSES INDUCED BY HIGH SPEED MACHINING WITH ROUND EDGE CUTTING TOOLS , 2005 .

[47]  Thomas Childs,et al.  Metal Machining: Theory and Applications , 2000 .

[48]  Takashi Ueda,et al.  On The Measurement of Temperature in Material Removal Processes , 2007 .

[49]  Olivier Dalverny,et al.  A three-dimensional transient numerical model of milling , 2001 .

[50]  Tuğrul Özel,et al.  Predictive Analytical and Thermal Modeling of Orthogonal Cutting Process—Part II: Effect of Tool Flank Wear on Tool Forces, Stresses, and Temperature Distributions , 2006 .

[51]  H. Chandrasekaran,et al.  Investigation of the effects of tool micro-geometry and coating on tool temperature during orthogonal turning of quenched and tempered steel , 2004 .

[52]  Paul Mativenga,et al.  An investigation of the tool-chip contact length and wear in high-speed turning of EN19 steel , 2004 .

[53]  Tarek Mabrouki,et al.  A contribution to a qualitative understanding of thermo-mechanical effects during chip formation in hard turning , 2006 .

[54]  Olivier Dalverny,et al.  2D AND 3D NUMERICAL MODELS OF METAL CUTTING WITH DAMAGE EFFECTS. , 2004 .

[55]  Paul K. Wright,et al.  Effect of Rake Face Design on Cutting Tool Temperature Distributions , 1980 .

[56]  S. Melkote,et al.  Material Strengthening Mechanisms and Their Contribution to Size Effect in Micro-Cutting , 2006 .

[57]  R. Komanduri,et al.  Thermal modeling of the metal cutting process — Part II: temperature rise distribution due to frictional heat source at the tool–chip interface , 2001 .

[58]  Jing Shi,et al.  On predicting chip morphology and phase transformation in hard machining , 2006 .

[59]  Xiaomin Deng,et al.  A finite element study of the effect of friction in orthogonal metal cutting , 2002 .

[60]  Y. Shin,et al.  Thermo-mechanical modeling of orthogonal machining process by finite element analysis , 1999 .

[61]  M E Crowley,et al.  Evaluation of implicit numerical methods for building energy simulation , 1998 .

[62]  J. Schmidt,et al.  2D FEM estimate of tool wear in turning operation , 2005 .

[63]  Steven Y. Liang,et al.  CUTTING TEMPERATURE MODELING BASED ON NON-UNIFORM HEAT INTENSITY AND PARTITION RATIO , 2005 .