Aluminium surface treatment with ceramic phases using diode laser

[1]  T. Tański,et al.  The influence of laser alloying on the structure and mechanical properties of AlMg5Si2Mn surface layers , 2016 .

[2]  M. Król,et al.  Properties of the Aluminium Alloy EN AC-51100 after Laser Surface Treatment , 2016 .

[3]  S. Boczkal,et al.  Effect of Al2O3 Ceramic Particles on Corrosion Behaviour and Tribological Properties of Nickel Composite Coatings , 2016 .

[4]  Aleksander Lisiecki,et al.  Welding of Thermomechanically Rolled Fine-Grain Steel by Different Types of Lasers/ Spawanie Stali Drobnoziarnistej Walcowanej Termomechanicznie Laserami Różnego Typu , 2014 .

[5]  T. Tański.  Determining of laser surface treatment parameters used for light metal alloying with ceramic powders , 2014 .

[6]  M. Gwoździk,et al.  Studies on the adhesion of oxide layer formed on X10CrMoVNb9-1 steel , 2014 .

[7]  K. Labisz.  Microstructure and mechanical properties of high power diode laser (HPDL) treated cast aluminium alloys , 2014 .

[8]  M. Gwoździk,et al.  Analysis of crystallite size and lattice deformations changes in an oxide layer on P91 steel , 2013 .

[9]  T. Tański,et al.  Unique properties, development perspectives and expected applications of laser treated casting magnesium alloys , 2012 .

[10]  L. Dobrzański,et al.  Effect of Laser Surface Melting on Structure and Properties of a High Speed Tool Steel , 2011 .

[11]  R. Bidulský,et al.  Effect of Different Vacuum Heat Treatments on the Microstructure of a Low Alloyed Sintered Steel , 2011 .

[12]  L. Dobrzański,et al.  Characterization Performance of Laser Melted Commercial Tool Steels , 2010 .

[13]  L. Dobrzański,et al.  Optimization of Heat Treatment Conditions of Magnesium Cast Alloys , 2010 .

[14]  L. Dobrzański,et al.  Phases and Structure Characteristics of the Near Eutectic Al-Sl-Cu Alloy Using Derivative Thermo Analysis , 2010 .

[15]  Milin Zhang,et al.  The corrosion of a novel Mg–11Li–3Al–0.5RE alloy in alkaline NaCl solution , 2009 .

[16]  L. Dobrzański,et al.  Structure and Properties of the 32CrMoV12-28 Steel Alloyed with WC Powder Using HPDL Laser , 2006 .

[17]  Seong‐Hyeon Hong,et al.  Fabrication of ultrafine TaC powders by mechano-chemical process , 2004 .

[18]  Gerry Byrne,et al.  A review of the use of high power diode lasers in surface hardening , 2004 .

[19]  L. J. Yang.  Wear coefficient of tungsten carbide against hot-work tool steel disc with two different pin settings , 2004 .

[20]  H. Uchida,et al.  Fatigue behavior and fractography of laser-processed hot work tool steel , 2004 .

[21]  Kazunari Mizumoto,et al.  Synthesis of iron–tungsten alloy on mild steel by laser surface alloying , 1998 .

[22]  Y. Guangli,et al.  EFFECT OF A SINGLE PEAK OVERLOAD ON PHYSICALLY SHORT FATIGUE CRACK RETARDATION IN AN AXLE‐STEEL , 1996 .

[23]  Z. Brytan.  Microstructural Characterization of Lean Duplex Stainless Steel UNS S32101 Welded Joints Using Electron Backscatter Diffraction , 2013 .

[24]  R. Filip.  Laser nitriding of the surface layer of Ti6Al4V titanium alloy , 2008 .