Numerical investigation of the influence of companion drops on drop-on-demand ink jetting

In this study we characterized and investigated the specific phenomenon of “companion drops” in the drop-on-demand (DOD) ink jetting process. A series of simulations based on a piezoelectric DOD printhead system is presented, adapting the volume-of-fluid (VOF) interface-capturing method to track the boundary evolution and model the interfacial physics. The results illustrate the causality between the generation of companion drops and droplet deviation behavior, as well as their close correlations with ink jetting straightness and printing accuracy. The characteristics of companion drops are summarized and compared with those of satellite drops. Also, a theoretical mechanism for the generation of companion drops is presented, and their effects and behaviors are analyzed and discussed. Finally, the effects of critical factors on the generation of companion drops are investigated and characterized based on variations in the printable pressure range. Recommendations are given for the suppression of companion drops and for the improvement of printing accuracy.

[1]  Raphael Semiat,et al.  Ink drop motion in wide-format printers: I. Drop flow from Drop-On-Demand (DOD) printing heads , 2009 .

[2]  Gihun Son,et al.  A Level-Set Method for Simulation of a Thermal Inkjet Process , 2008 .

[3]  E. J. Vega,et al.  Global and local instability of flow focusing: The influence of the geometry , 2010 .

[4]  S. Chandra,et al.  Producing droplets smaller than the nozzle diameter by using a pneumatic drop-on-demand droplet generator , 2007 .

[5]  Myeong Ho Lee,et al.  Control of droplet formation for low viscosity fluid by double waveforms applied to a piezoelectric inkjet nozzle , 2011, Microelectron. Reliab..

[6]  Graham D. Martin,et al.  Links Between Ink Rheology, Drop-on-Demand Jet Formation, and Printability , 2009 .

[7]  Weng-Sing Hwang,et al.  Development of a three-dimensional simulation system for micro-inkjet and its experimental verification , 2004 .

[9]  Young Jin Kim,et al.  The fluid property dependency on ink jetting characteristics , 2005, IEEE International Conference on Mechatronics, 2005. ICM '05..

[10]  Patrick K. Notz,et al.  Satellite drops: Unexpected dynamics and change of scaling during pinch-off , 2001 .

[11]  James A. Sethian,et al.  A coupled quadrilateral grid level set projection method applied to ink jet simulation , 2005 .

[12]  Jooho Moon,et al.  Influence of fluid physical properties on ink-jet printability. , 2009, Langmuir : the ACS journal of surfaces and colloids.

[13]  J. E. Fromm,et al.  Numerical calculation of the fluid dynamics of drop-on-demand jets , 1984 .

[14]  Osman A. Basaran,et al.  Computational analysis of drop-on-demand drop formation , 2007 .

[15]  V. Altuzar,et al.  Atmospheric pollution profiles in Mexico City in two different seasons , 2003 .

[16]  Brian Derby,et al.  Ink-jet delivery of particle suspensions by piezoelectric droplet ejectors , 2005 .

[17]  N. Ashgriz,et al.  Drop-on-Demand Drop Generators , 2011 .

[18]  Wallace W. Carr,et al.  An experimental study of drop-on-demand drop formation , 2006 .

[19]  J. Brackbill,et al.  A continuum method for modeling surface tension , 1992 .

[20]  H. Wijshoff,et al.  The dynamics of the piezo inkjet printhead operation , 2010 .

[21]  Kung Linliu,et al.  Influence of liquid hydrophobicity and nozzle passage curvature on microfluidic dynamics in a drop ejection process , 2009 .

[22]  Kye-Si Kwon,et al.  Waveform Design Methods for Piezo Inkjet Dispensers Based on Measured Meniscus Motion , 2009, Journal of Microelectromechanical Systems.

[23]  Kye-Si Kwon,et al.  Experimental analysis of waveform effects on satellite and ligament behavior via in situ measurement of the drop-on-demand drop formation curve and the instantaneous jetting speed curve , 2010 .

[24]  Numerical investigation of the effect of a transducer pulse on the microfluidic control of a piezoelectric printhead , 2010 .

[25]  Johan Frederik Dijksman,et al.  Precision ink jet printing of polymer light emitting displays , 2007 .

[26]  Wallace W. Carr,et al.  Visualization of drop-on-demand inkjet: Drop formation and deposition , 2006 .

[27]  Levent Yobas,et al.  High-performance flow-focusing geometry for spontaneous generation of monodispersed droplets. , 2006, Lab on a chip.