Dynamic Properties of 316L Stainless Steel Repaired Using Electron Beam Additive Manufacturing

[1]  Assefa Asmare Tsegaw,et al.  Metal hybrid additive manufacturing: state-of-the-art , 2022, Progress in Additive Manufacturing.

[2]  S. Razorenov,et al.  The Strength of Inconel 625, Manufactured by the Method of Direct Laser Deposition under Sub-Microsecond Load Duration , 2021, Metals.

[3]  N. Parab,et al.  Investigation of Dynamic Fracture Behavior of Additively Manufactured Al-10Si-Mg Using High-Speed Synchrotron X-ray Imaging , 2019, Challenges in Mechanics of Time Dependent Materials, Fracture, Fatigue, Failure and Damage Evolution, Volume 2.

[4]  A. Bandyopadhyay,et al.  Additive manufacturing in repair: Influence of processing parameters on properties of Inconel 718 , 2019, Materials Letters.

[5]  K. Dilger,et al.  Remanufacturing of die casting dies made of hot-work steels by using the wire-based electron-beam welding with an in situ heat treatment , 2019, Welding in the World.

[6]  David R. Jones,et al.  Gas Gun Flyer Plate Impact Testing of Stainless Steel Deposited by Low Pressure Plasma Spraying and Cold Gas Dynamic Spraying , 2019, Journal of Thermal Spray Technology.

[7]  J. Gholipour,et al.  Titanium Alloy Repair with Wire-Feed Electron Beam Additive Manufacturing Technology , 2019, Advances in Materials Science and Engineering.

[8]  D. Loison,et al.  Effects of additive manufacturing on the dynamic response of AlSi10Mg to laser shock loading , 2019, Materials Science and Engineering: A.

[9]  Edward William Reutzel,et al.  Effect of processing conditions on the microstructure, porosity, and mechanical properties of Ti-6Al-4V repair fabricated by directed energy deposition , 2019, Journal of Materials Processing Technology.

[10]  B. Ndefru,et al.  Spall fracture in additive manufactured tantalum , 2018, Journal of Applied Physics.

[11]  Wang Zhandong,et al.  Microstructure and mechanical properties of HSLA-100 steel repaired by laser metal deposition , 2018, Surface and Coatings Technology.

[12]  C. Trujillo,et al.  Effect of peak stress and tensile strain-rate on spall in tantalum , 2018, Journal of Applied Physics.

[13]  Jun Yu Li,et al.  Deformation mechanism during dynamic loading of an additively manufactured AlSi10Mg_200C , 2018 .

[14]  J. S. Zuback,et al.  Additive manufacturing of metallic components – Process, structure and properties , 2018 .

[15]  S. R. Chen,et al.  Structure/property (constitutive and spallation response) of additively manufactured 316L stainless steel , 2017 .

[16]  N. Frage,et al.  Dynamic response of AlSi10Mg alloy fabricated by selective laser melting , 2017 .

[17]  Xin Lin,et al.  The tensile deformation behavior of laser repaired Inconel 718 with a non-uniform microstructure , 2017 .

[18]  David R. Jones,et al.  Spall fracture in additive manufactured Ti-6Al-4V , 2016 .

[19]  Hang Zheng,et al.  TC17 titanium alloy laser melting deposition repair process and properties , 2016 .

[20]  A. Mertens,et al.  Laser cladding as repair technology for Ti–6Al–4V alloy: Influence of building strategy on microstructure and hardness , 2015 .

[21]  N. Shamsaei,et al.  An overview of Direct Laser Deposition for additive manufacturing; Part I: Transport phenomena, modeling and diagnostics , 2015 .

[22]  N. Shamsaei,et al.  An overview of Direct Laser Deposition for additive manufacturing; Part II: Mechanical behavior, process parameter optimization and control , 2015 .

[23]  E. Nishida,et al.  Comparative shock response of additively manufactured versus conventionally wrought 304L stainless steel , 2015 .

[24]  R. Lewis,et al.  Assessment of laser cladding as an option for repairing/enhancing rails , 2015 .

[25]  Edward William Reutzel,et al.  A survey of sensing and control systems for machine and process monitoring of directed-energy, metal-based additive manufacturing , 2015 .

[26]  Vladimir Luzin,et al.  Effect of laser clad repair on the fatigue behaviour of ultra-high strength AISI 4340 steel , 2014 .

[27]  William E. Frazier,et al.  Metal Additive Manufacturing: A Review , 2014, Journal of Materials Engineering and Performance.

[28]  T. Germann,et al.  Effect of loading direction on grain boundary failure under shock loading , 2014 .

[29]  Neelesh Kumar Jain,et al.  Causes of failure and repairing options for dies and molds: A review , 2013 .

[30]  Ricardo A. Lebensohn,et al.  Effects of grain size and boundary structure on the dynamic tensile response of copper , 2011 .

[31]  Daniel H. Dolan,et al.  SIRHEN: a data reduction program for photonic Doppler velocimetry measurements , 2010 .

[32]  O. Strand,et al.  Compact system for high-speed velocimetry using heterodyne techniques , 2006 .

[33]  A. Schwartz,et al.  Effect of microstructural length scales on spall behavior of copper , 2004 .

[34]  Telmo G. Santos,et al.  Revisiting fundamental welding concepts to improve additive manufacturing: From theory to practice , 2020 .

[35]  John S. Carpenter,et al.  Wire-Based Additive Manufacturing of Stainless Steel Components , 2020 .

[36]  C. G. Krishnadas Nair,et al.  Laser metal deposition repair applications for Inconel 718 alloy , 2017 .

[37]  B. Graf,et al.  Laser Metal Deposition as Repair Technology for a Gas Turbine Burner Made of Inconel 718 , 2016 .

[38]  B. Graf,et al.  Laser Metal Deposition as Repair Technology for Stainless Steel and Titanium Alloys , 2012 .

[39]  Guijun Bi,et al.  Restoration of Nickel-Base Turbine Blade Knife-Edges with Controlled Laser Aided Additive Manufacturing , 2011 .