Studies on Tensile Behaviour of Selective Laser Melted 316L Stainless Steel Using SEM Straining Stage

[1]  D. Raabe,et al.  Steels in additive manufacturing: A review of their microstructure and properties , 2020 .

[2]  M. Mukherjee.  Effect of build geometry and orientation on microstructure and properties of additively manufactured 316L stainless steel by laser metal deposition , 2019, Materialia.

[3]  Kaushik Chatterjee,et al.  Non-equilibrium microstructure, crystallographic texture and morphological texture synergistically result in unusual mechanical properties of 3D printed 316L stainless steel , 2019, Additive Manufacturing.

[4]  S. Chowdhury,et al.  Stacking Fault Energy of Austenite Phase in Medium Manganese Steel , 2019, Metallurgical and Materials Transactions A.

[5]  N. Provatas,et al.  The Significance of Spatial Length Scales and Solute Segregation in Strengthening Rapid Solidification Microstructures of 316L Stainless Steel , 2019, Acta Materialia.

[6]  Young‐kook Lee,et al.  Anisotropic Mechanical Behavior of Additive Manufactured AISI 316L Steel , 2019, Metallurgical and Materials Transactions A.

[7]  Yuanjian Hong,et al.  Formation of strain-induced martensite in selective laser melting austenitic stainless steel , 2019, Materials Science and Engineering: A.

[8]  Radovan Kovacevic,et al.  An investigation on mechanical and microstructural properties of 316LSi parts fabricated by a robotized laser/wire direct metal deposition system , 2018, Additive Manufacturing.

[9]  Jean-Pierre Kruth,et al.  Microstructure evolution of 316L produced by HP-SLM (high power selective laser melting) , 2018, Additive Manufacturing.

[10]  Chee Kai Chua,et al.  Simultaneously enhanced strength and ductility for 3D-printed stainless steel 316L by selective laser melting , 2018, NPG Asia Materials.

[11]  Ting Zhu,et al.  Additively manufactured hierarchical stainless steels with high strength and ductility. , 2018, Nature materials.

[12]  Liang Hao,et al.  Effect of build orientation on the surface quality, microstructure and mechanical properties of selective laser melting 316L stainless steel , 2017 .

[13]  G. Pacchioni.  3D printing: May the strength be with you , 2017 .

[14]  L. Hitzler,et al.  On the Anisotropic Mechanical Properties of Selective Laser-Melted Stainless Steel , 2017, Materials.

[15]  Filipe S. Silva,et al.  316L stainless steel mechanical and tribological behavior—A comparison between selective laser melting, hot pressing and conventional casting , 2017 .

[16]  Y. Zhong,et al.  Intragranular cellular segregation network structure strengthening 316L stainless steel prepared by selective laser melting , 2016 .

[17]  Yusheng Shi,et al.  Differences in microstructure and properties between selective laser melting and traditional manufacturing for fabrication of metal parts: A review , 2015 .

[18]  Surendar Marya,et al.  Microstructural Development and Technical Challenges in Laser Additive Manufacturing: Case Study with a 316L Industrial Part , 2015, Metallurgical and Materials Transactions B.

[19]  K. Kunze,et al.  Texture, anisotropy in microstructure and mechanical properties of IN738LC alloy processed by selective laser melting (SLM) , 2015 .

[20]  Konrad Wegener,et al.  Fatigue performance of additive manufactured metallic parts , 2013 .

[21]  Young‐kook Lee.  Microstructural evolution during plastic deformation of twinning-induced plasticity steels , 2012 .

[22]  D. Raabe,et al.  The effect of grain size and grain orientation on deformation twinning in a Fe-22 wt.% Mn-0.6 wt.% C TWIP steel , 2010 .

[23]  G. Frommeyer,et al.  Enhanced Mechanical Properties of a Novel High-Nitrogen Cr-Mn-Ni-Si Austenitic Stainless Steel via TWIP/TRIP Effects , 2009 .

[24]  S. Takaki,et al.  Deformation twinning in high-nitrogen austenitic stainless steel , 2007 .

[25]  Li Meng,et al.  Dependence of deformation twinning on grain orientation in a high manganese steel , 2006 .

[26]  L. Froyen,et al.  Binding Mechanisms in Selective Laser Sintering and Selective Laser Melting , 2004 .