APPLICATION OF BLOCK THEORY MODELING ON SPATIAL BLOCK TOPOLOGICAL IDENTIFICATION TO ROCK SLOPE STABILITY ANALYSIS

Rock slopes stability has been one of the fundamental issues facing geotechnical engineering researchers. Due to the pre-existing joints, the intactness of the rock is weakened. The mechanical characteristics are changed correspondingly along with joint-induced stress redistribution within the rock mass if the sliding limit at the joint or part of it is exceeded. In this study, spatial block topological identification techniques are applied to distinguish all blocks cut by 3D finite random or fixed discontinuities. Based on the available photographic information of rock slopes, the sliding forces and the corresponding factor of safety are evaluated through limit equilibrium conditions by the classic block theory. The rock slope stability analysis software, GeoSMA-3D (Geotechnical Structure and Model Analysis), satisfying the requirements of spatial block modeling, joint plane simulation, key block identification and analysis and sliding process display, was developed. The application of such a software on the analysis of a rock slope, which is located near the inlet of Daiyuling No. 1 tunnel on the Zhuanghe–Gaizhou highway networks, was performed. The assessed results were compared with the monitored data to validate the effectiveness of such software.

[1]  Larbi Siad,et al.  Stability analysis of jointed rock slope , 1998 .

[2]  Gioacchino Viggiani,et al.  Strain localization in sand: an overview of the experimental results obtained in Grenoble using stereophotogrammetry , 2004 .

[3]  Richard E. Goodman,et al.  Two dimensional discontinuous deformation analysis , 1985 .

[4]  Larbi Siad.  Stability analysis of jointed rock slopes reinforced by passive, fully grouted bolts , 2001 .

[5]  Gregory B. Baecher,et al.  The effect of discontinuity persistence on rock slope stability , 1983 .

[6]  Jean Salençon,et al.  Introduction to the yield design theory and its applications to soil mechanics , 1990 .

[7]  Chung-In Lee,et al.  Modeling the Effects of Heterogeneity and Anisotropy on the Excavation Damaged/Disturbed Zone (EDZ) , 2009 .

[8]  P. Warburton.  Vector stability analysis of an arbitrary polyhedral rock block with any number of free faces , 1981 .

[9]  P. Cundall,et al.  A discrete numerical model for granular assemblies , 1979 .

[10]  K. Kaneko,et al.  Measurement and interpretation of long-term deformation of a rock slope at the Ikura limestone quarry, Japan , 2009 .

[11]  W. H. Peters,et al.  Application of an optimized digital correlation method to planar deformation analysis , 1986, Image Vis. Comput..

[12]  L. Siad,et al.  Seismic stability analysis of fractured rock slopes by yield design theory , 2003 .

[13]  N. Morgenstern,et al.  The analysis of the stability of general slip surfaces , 1965 .

[14]  R. Butterfield,et al.  A Stero-Photogrammetric Method for Measuring Displacement Fields , 1970 .

[15]  W. A. Take,et al.  Soil deformation measurement using particle image velocimetry (PIV) and photogrammetry , 2003 .

[16]  Doug Stead,et al.  Numerical analysis of initiation and progressive failure in natural rock slopes—the 1991 Randa rockslide , 2004 .

[17]  John A. Hudson,et al.  Numerical methods in rock mechanics , 2002 .

[18]  P. Lunardi,et al.  Rock mechanics investigations for rock slope stability assessment , 1994 .

[19]  Lysandros Pantelidis.  Rock slope stability assessment through rock mass classification systems , 2009 .

[20]  John Coggan,et al.  Developments in the characterization of complex rock slope deformation and failure using numerical modelling techniques , 2006 .

[21]  A. Bishop.  The use of the Slip Circle in the Stability Analysis of Slopes , 1955 .