Prediction and measurement of welding distortion of a spherical structure assembled from multi thin plates

Abstract A spherical structure assembled from 14 thin bent plates and two circular polar plates was taken as the research object and its welding distortion was investigated in this study. Firstly, the welding distortion due to each welding line is measured by experiment. Then, the spherical structure was modeled by shell element and its welding distortion produced by each welding line was evaluated using the inherent deformation method proposed by authors. The computational process requires a short time when the inherent deformation method is employed. To determine the inherent deformation existing in the welding lines, a computed model with 3D solid element for a typical butt welded joint was applied and one case of the detail transient analysis by Thermal Elastic Plastic Finite Element Method was performed. The computed and measured welding distortion show that the radial displacements on the welding lines and at the center of the top and the bottom polar plates are toward the inside of the spherical structure. The radial displacements at the positions between the welding lines are toward the outside of the spherical structure. The welding distortion at the measuring points changing with each welding line is well predicted using the inherent deformation method compared with the measured results.

[1]  Yukio Ueda,et al.  A New Measuring Method of Residual Stresses with the Aid of Finite Element Method and Reliability of Estimated Values , 1975 .

[2]  P. Michaleris,et al.  Prediction of welding distortion , 1997 .

[3]  Lars-Erik Lindgren,et al.  Deformations and stresses in welding of shell structures , 1988 .

[4]  E. Friedman.  Thermomechanical Analysis of the Welding Process Using the Finite Element Method , 1975 .

[5]  Hidekazu Murakawa,et al.  Prediction of Deformation for Large Welded Structures Based on Inherent Strain(Mechanics, Strength & Structural Design) , 2004 .

[6]  K. Masubuchi.  Analysis of Welded Structures , 1980 .

[7]  Hisashi Serizawa,et al.  Actual application of FEM to analysis of large scale mechanical problems in welding , 2007 .

[8]  A. Bachorski,et al.  Finite-element prediction of distortion during gas metal arc welding using the shrinkage volume approach , 1999 .

[9]  Ninshu Ma,et al.  Concept of inherent strain, inherent stress, inherent deformation and inherent force for prediction of welding distortion and residual stress , 2010 .

[10]  Jianxun Zhang,et al.  Study of welding inherent deformations in thin plates based on finite element analysis using interactive substructure method , 2009 .

[11]  Yukio Ueda,et al.  ANALYSIS OF THERMAL ELASTIC-PLASTIC STRESS AND STRAIN DURING WELDING BY FINITE ELEMENT METHOD , 1971 .

[12]  S. Sone,et al.  Prediction of Welding Distortion by Elastic Finite Element Analysis using Inherent Deformation Estimated Through Inverse Analysis , 2005 .

[13]  Yukio Ueda,et al.  Prediction of Welding Deformation and Residual Stress by Elastic FEM Based on Inherent Strain (Report I) : Mechanism of Inherent Strain Production(Mechanics, Strength & Structure Design) , 1997 .

[14]  Tom Gray,et al.  Computationally efficient welding distortion simulation techniques , 2005 .

[15]  Pedro V. Marcal,et al.  A NUMERICAL THERMO-MECHANICAL MODEL FOR THE WELDING AND SUBSEQUENT LOADING OF A FABRICATED STRUCTURE , 1973 .

[16]  Pingsha Dong,et al.  Numerical Prediction of Buckling in Ship Panel Structures , 2006 .

[17]  Y. Ueda,et al.  The Characteristics of the Source of Welding Residual Stress (Inherent Strain) and its Application to Measurement and Prediction , 1991 .

[18]  Wei Liang,et al.  Numerical simulation of welding distortion in large structures , 2007 .

[19]  Hidekazu Murakawa.  Application of Inherent Deformation and Interface Element to Prediction of Welding Distortion during Assembly Process from Cutting through Straightening , 2010 .