Tooth-Coil Permanent Magnet Synchronous Machine Design for Special Applications

[1]  Janne Nerg,et al.  Permanent-Magnet Length Effects in AC Machines , 2010, IEEE Transactions on Magnetics.

[2]  M. Trlep,et al.  Evaluation of saturation and cross-magnetization effects in interior permanent magnet synchronous motor , 2001, Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248).

[3]  Lasse Laurila,et al.  High power density integrated electro-hydraulic energy converter for heavy hybrid off-highway working vehicles , 2014 .

[4]  Ayman M. El-Refaie,et al.  Fractional-Slot Concentrated-Windings Synchronous Permanent Magnet Machines: Opportunities and Challenges , 2010, IEEE Transactions on Industrial Electronics.

[5]  K. Bradley,et al.  High Torque Density PM Machines for High Performance Operation , 2007, IECON 2007 - 33rd Annual Conference of the IEEE Industrial Electronics Society.

[6]  Geun-Ho Lee.  Active Cancellation of PMSM Torque Ripple Caused by Magnetic Saturation for EPS Applications , 2010 .

[7]  R. Dutta,et al.  Winding Inductances of an Interior Permanent Magnet (IPM) Machine With Fractional Slot Concentrated Winding , 2012, IEEE Transactions on Magnetics.

[8]  J. S. Hsu.  Report on Toyota/Prius Motor Design and Manufacturing Assessment , 2004 .

[9]  Z. Zhu,et al.  Eddy-current loss in the rotor magnets of permanent-magnet brushless machines having a fractional number of slots per pole , 2005, IEEE Transactions on Magnetics.

[10]  Henk Polinder,et al.  Eddy-current losses in the segmented surface-mounted magnets of a PM machine , 1999 .

[11]  H. Grop,et al.  Stator slot leakage in AC-machines equipped with fractional conductor windings , 2009, 2009 International Conference on Electrical Machines and Systems.

[12]  Z. Zhu,et al.  Influence of design parameters on cogging torque in permanent magnet machines , 1997 .

[13]  Ayman Mohamed Fawzi EL-Refaie,et al.  Fault-tolerant permanent magnet machines: a review , 2011 .

[14]  J. Nerg,et al.  Effect of Lamination Stack Ends and Radial Cooling Channels on No-Load Voltage and Inductances of Permanent-Magnet Synchronous Machines , 2011, IEEE Transactions on Magnetics.

[15]  Erich Schmidt,et al.  Finite element analysis of permanent magnet synchronous machines with fractional slot tooth coil windings , 2011, Elektrotech. Informationstechnik.

[16]  Stefano Di Cairano,et al.  Engine power smoothing energy management strategy for a series hybrid electric vehicle , 2011, Proceedings of the 2011 American Control Conference.

[17]  Z.Q. Zhu,et al.  Reduction of cogging torque in interior-magnet brushless machines , 2003, Digest of INTERMAG 2003. International Magnetics Conference (Cat. No.03CH37401).

[18]  Thomas M. Jahns,et al.  Winding Inductances of Fractional Slot Surface-Mounted Permanent Magnet Brushless Machines , 2008, 2008 IEEE Industry Applications Society Annual Meeting.

[19]  G. Huth.  Permanent-magnet-excited AC servo motors in tooth-coil technology , 2005, IEEE Transactions on Energy Conversion.

[20]  Da-Woon Choi,et al.  Effects of MMF Harmonics on Rotor Eddy-Current Losses for Inner-Rotor Fractional Slot Axial Flux Permanent Magnet Synchronous Machines , 2012, IEEE Transactions on Magnetics.

[21]  Torben N. Matzen,et al.  Sensorless characteristics of hybrid PM machines at zero and low speed , 2009, 2009 IEEE Energy Conversion Congress and Exposition.

[22]  N. Matsui,et al.  Sensorless-oriented design of IPM motors for general industrial applications , 2008, 2008 18th International Conference on Electrical Machines.

[23]  John James Anthony Cullen,et al.  Favourable slot and pole number combinations for fault-tolerant PM machines , 2004 .

[24]  Christos Mademlis,et al.  Magnetic and thermal performance of a synchronous motor under loss minimization control , 2000 .

[25]  A. M. El-Refaie,et al.  Motors/generators for traction/propulsion applications: A review , 2013, IEEE Vehicular Technology Magazine.

[26]  N. Bianchi,et al.  Design considerations for fractional-slot winding configurations of synchronous machines , 2006, IEEE Transactions on Industry Applications.

[27]  N. Bianchi,et al.  Impact of the Rotor Yoke Geometry on Rotor Losses in Permanent-Magnet Machines , 2010, IEEE Transactions on Industry Applications.

[28]  T. Undeland,et al.  Optimum torque performance in PMSM drives above rated speed , 1991, Conference Record of the 1991 IEEE Industry Applications Society Annual Meeting.

[29]  F. Magnussen,et al.  Parasitic Effects in PM Machines With Concentrated Windings , 2005, IEEE Transactions on Industry Applications.

[30]  Nicola Bianchi,et al.  Design techniques for reducing the cogging torque in surface-mounted PM motors , 2000, Conference Record of the 2000 IEEE Industry Applications Conference. Thirty-Fifth IAS Annual Meeting and World Conference on Industrial Applications of Electrical Energy (Cat. No.00CH37129).

[31]  T.J.E. Miller,et al.  Field-weakening performance of brushless synchronous AC motor drives , 1994 .

[32]  J. A. Guemes,et al.  Comparative study of PMSM with integer-slot and fractional-slot windings , 2010, The XIX International Conference on Electrical Machines - ICEM 2010.

[33]  Alfio Consoli,et al.  Industry application of zero-speed sensorless control techniques for PM synchronous motors , 2001 .

[34]  Juha Pyrhonen,et al.  Design of integrated electro-hydraulic power unit for hybrid mobile working machines , 2011, Proceedings of the 2011 14th European Conference on Power Electronics and Applications.

[35]  Tao Fan,et al.  Evaluation of heat transfer characteristic of Aluminum Nitride (AlN) potting compound for the end windings of permanent magnet synchronous machines , 2011, 2011 International Conference on Electrical and Control Engineering.

[36]  Massimo Barcaro,et al.  Remarks on Torque Estimation Accuracy in Fractional-Slot Permanent-Magnet Motors , 2012, IEEE Transactions on Industrial Electronics.

[37]  P. Viarouge,et al.  Synthesis of high performance PM motors with concentrated windings , 2002 .