Novel Optimization Approach in Ultrasonic Machining: Unilateral Compensation for Resonant Vibration in Primary Side

Resonant frequency and impedance matching have great significance for the vibration performance and online monitoring of the rotary ultrasonic machining. Network compensation is a typical solution to match the resonant frequency and the impedance between the rotary ultrasonic holder (RUH) and the ultrasonic transducer. However, the traditional bilateral compensation method could adversely affect the rotary dynamic balance of the RUH. Currently, the existing unilateral compensation methods can only realize the resonant frequency matching. A novel unilateral compensation method that satisfies both the resonant frequency and the impedance matching is proposed. First, the impedance model of the RUH vibrating system is established according to its equivalent circuit. It is found that, without any compensation methods, the resonant frequency and the impedance between the RUH and the transducer have deviated. Second, the primary-series and primary-parallel compensation topologies are applied to the RUH system, and the expressions of compensation capacitance value, voltage gain, power transfer efficiency, and output active power are derived. The deviations of the resonant frequency and the impedance are eliminated with primary-series compensation topology; and as a result, the voltage gain is increased from 0.267 to 0.90, the output active power is 11.3 times than that without compensation. Third, the state-space model of primary-series topology is constructed. Finally, the above theoretical results are verified by the experimental results.

[1]  Johann W. Kolar,et al.  Optimization of rotary transformer for high-speed applications , 2013, 2013 IEEE 14th Workshop on Control and Modeling for Power Electronics (COMPEL).

[2]  W. P. Mason.  Electromechanical transducers and wave filters , 1942 .

[3]  Xinggang Jiang,et al.  Self-Compensation Theory and Design of Contactless Energy Transfer and Vibration System for Rotary Ultrasonic Machining , 2018, IEEE Transactions on Power Electronics.

[5]  Liping Liu,et al.  Efficiency-based compensations and the mechanical load dependencies of rotary transformer for rotary ultrasonic machining applications , 2015 .

[6]  Bin Lin,et al.  Power Transfer Performance and Cutting Force Effects of Contactless Energy Transfer System for Rotary Ultrasonic Grinding , 2016, IEEE Transactions on Industrial Electronics.

[7]  Yoon-Ho Kim,et al.  Design and Implementation of a Rectangular-Type Contactless Transformer , 2011, IEEE Transactions on Industrial Electronics.

[8]  Bin Lin,et al.  Optimization of rotary transformer for RUM with secondary self-compensation , 2018 .

[9]  Jun Imaoka,et al.  Design of series-parallel combined resonant circuit with rotary transformer used for ultrasonic spindle drive , 2017, 2017 IEEE 3rd International Future Energy Electronics Conference and ECCE Asia (IFEEC 2017 - ECCE Asia).

[10]  Yingxiang Liu,et al.  A Two-DOF Ultrasonic Motor Using a Longitudinal–Bending Hybrid Sandwich Transducer , 2019, IEEE Transactions on Industrial Electronics.

[11]  N. Churi,et al.  ROTARY ULTRASONIC MACHINING OF HARD-TO-MACHINE MATERIALS , 2010 .

[12]  Jozef Peterka,et al.  Cross section of Machined Layer for Rotary Ultrasonic Machining with a Hollow Drill , 2012 .

[13]  L. Encica,et al.  Comparison of winding topologies in a pot core rotating transformer , 2010, 2010 12th International Conference on Optimization of Electrical and Electronic Equipment.

[14]  Weishan Chen,et al.  Actuating Mechanism and Analysis of a Square-Type Rotary Ultrasonic Stator Using Longitudinal Vibration Transducers , 2009 .

[15]  S. Singhal,et al.  Rotary Ultrasonic Machining: A Review , 2016 .

[16]  A. Mathieson,et al.  Characterisation of nonlinear behaviour of power ultrasonic drilling horns , 2009, 2009 IEEE International Ultrasonics Symposium.

[17]  Yingxiang Liu,et al.  Development of a Novel Ultrasonic Drill Using Longitudinal-Bending Hybrid Mode , 2017, IEEE Access.

[18]  Zhijun Wu,et al.  A bilateral capacitance compensation method for giant magnetostriction ultrasonic processing system , 2017 .

[19]  M. Razfar,et al.  Effect of cutting speed on tool life in ultrasonic-assisted milling process , 2013 .

[20]  Patrick Harkness,et al.  A design approach for longitudinal–torsional ultrasonic transducers , 2013 .

[21]  Ping Guo,et al.  Damage formation and suppression in rotary ultrasonic machining of hard and brittle materials: A critical review , 2018 .

[22]  Andreas Rosskopf,et al.  Inductive power transfer system with a rotary transformer for contactless energy transfer on rotating applications , 2016, 2016 IEEE International Symposium on Circuits and Systems (ISCAS).

[23]  Raju Pawade,et al.  Effect of process parameters on MRR, TWR and surface topography in ultrasonic machining of alumina–zirconia ceramic composite , 2014 .