Assessment of erosion of the ITER divertor targets during type I ELMs

This paper presents the results of a preliminary assessment conducted to estimate the thermal response and erosion lifetime of the ITER divertor targets clad either with carbon-fibre composite or tungsten during type I ELMs. The one-dimensional thermal/erosion model, used for the analyses, is briefly described. It includes all the key surface heat transfer processes such as evaporation, melting, and radiation, and their interaction with the bulk thermal response, and it is based on an implicit finite-difference scheme, which allows for temperature-dependent material properties. The cases analysed clarify the influence of several ELM parameters on the heat transfer and erosion processes at the target (i.e. characteristic plasma ELM energy loss from the pedestal, fraction of the energy reaching the divertor, broadening of the strike-points during ELMs, duration and waveform of the ELM heat load) and design/material parameters (i.e. inclination of the target, type and thickness of the armour material, and for tungsten only, fraction of the melt layer loss). Comparison is made between cases where all ELMs are characterized by the same fixed averaged parameters, and cases where instead the characteristic parameters of each ELM are evaluated in a random fashion by using a standard Monte Carlo technique, based on distributions of some of the variables of interest derived from experiments in today's machines. Although uncertainties rule out providing firm quantitative predictions, the results of this study are useful to illustrate trends. Based on the results, the implications on the design and operation are discussed and priorities are determined for the R&D needed to reduce the remaining uncertainties.

[1]  A. Herrmann,et al.  Overview on stationary and transient divertor heat loads , 2002 .

[2]  Michael J. Berry,et al.  Thermochemical heat of ablation of solid carbon , 1989 .

[3]  G. Janeschitz.  Plasma–wall interaction issues in ITER , 2001 .

[4]  Martin Jakobi,et al.  Transport into and across the scrape-off layer in the ASDEX Upgrade divertor tokamak , 2002 .

[5]  A. Loarte,et al.  Basic divertor operation in ITER-FEAT , 2002 .

[6]  M. Sugihara,et al.  Characteristics of type I ELM energy and particle losses in existing devices and their extrapolation to ITER , 2003 .

[7]  J. Manickam,et al.  Disappearance of giant ELMs and appearance of minute grassy ELMs in JT-60U high-triangularity discharges , 2000 .

[8]  B. Bazylev,et al.  Melt layer erosion of metallic armour targets during off-normal events in tokamaks , 2002 .

[9]  W. Treutterer,et al.  Type II ELMy H modes on ASDEX Upgrade with good confinement at high density , 2001 .

[10]  P. Barabaschi,et al.  Key ITER plasma edge and plasma–material interaction issues , 2003 .

[11]  Jay Kesner,et al.  Dipole equilibrium and stability , 2001 .

[12]  R. Aymar,et al.  The ITER design , 2002 .

[13]  F. Kappler,et al.  Vertical target and FW erosion during off-normal events and impurity production and transport during ELMs typical for ITER-FEAT , 2001 .

[14]  Ahmed Hassanein,et al.  Surface melting and evaporation during disruptions in magnetic fusion reactors , 1984 .

[15]  G. Federici,et al.  RACLETTE: a model for evaluating the thermal response of plasma facing components to slow high power plasma transients. Part II: Analysis of ITER plasma facing components , 1997 .

[16]  D. Humphreys,et al.  DISRUPTION MITIGATION USING HIGH-PRESSURE NOBLE GAS INJECTION ON DIII-D , 2002 .

[17]  A. Kukushkin,et al.  Scaling of ITER divertor parameters – interpolation from 2D modelling and extrapolation , 2003 .

[18]  H. Würz,et al.  Impurity production and edge plasma pollution during ITER-FEAT ELMs , 2002 .

[19]  F. Kappler,et al.  A 2-D Numerical Simulation of ITER-FEAT Disruptive Hot Plasma-Wall Interaction and Model Validation against Disruption Simulation Experiments , 2001 .

[20]  Taina Kurki-Suonio,et al.  Formation and detection of internal transport barriers in low-current tokamaks , 2002 .

[21]  G. Federici,et al.  RACLETTE: a Model for Evaluating the Thermal Response of Plasma Facing Components to Slow High Power Plasma Transients. Part I: Theory and Description of Model Capabilities , 1997 .

[22]  D. Van Eester,et al.  Re-evaluation of ITER ion cyclotron operating scenarios , 2002 .

[23]  A. Loarte,et al.  Improved performance of ELMy H-modes at high density by plasma shaping in JET , 2002 .

[24]  G. Saibene,et al.  Characteristics and scaling of energy and particle losses during Type I ELMs in JET H-modes , 2002 .

[25]  J. Ahn,et al.  Boundary plasma and divertor phenomena in MAST , 2002 .

[26]  V. Riccardo,et al.  Disruption heat loads on the JET MkIIGB divertor , 2002 .

[27]  Helium removal from tokamaks , 1991 .

[28]  Martine Baelmans,et al.  B2-EIRENE simulation of ASDEX and ASDEX-Upgrade scrape-off layer plasmas , 1992 .

[29]  F. G. Rimini,et al.  Isotope scaling of the H mode power threshold on JET , 1999 .

[30]  C. H. Wu,et al.  Material/Plasma Surface Interaction Issues Following Neutron Damage , 2003 .

[31]  C. H. Skinner,et al.  Plasma{material interactions in current tokamaks and their implications for next step fusion reactors , 2001 .

[32]  G. Janeschitz,et al.  Erosion of plasma-facing components in ITER☆ , 2002 .

[33]  Crpp.  Papers presented at the 24th EPS Conference on Controlled Fusion and Plasma Physics, Berchtesgaden, Germany, 9 - 13 June 1997 , 1997 .

[34]  H. Pacher,et al.  Erosion lifetime of ITER divertor plates , 1997 .

[35]  A. Loarte,et al.  Power deposition measurements in deuterium and helium discharges in JET MKIIGB divertor by IR-thermography , 2003 .

[36]  L. Horton,et al.  ELM energy and particle losses and their extrapolation to burning plasma experiments , 2003 .

[37]  A. Bergmann,et al.  Stationary and Transient Divertor Heat Flux Profiles and Extrapolation to ITER , 2003 .

[38]  G. Pautasso,et al.  Energy flux to the ASDEX-Upgrade diverter plates determined by thermography and calorimetry , 1995 .

[39]  S. Luckhardt,et al.  Experimental evidence of intermittent convection in the edge of magnetic confinement devices. , 2001, Physical review letters.

[40]  H. Zohm,et al.  DIVERTOR HEAT AND PARTICLE FLUX DUE TO ELMs IN DIII-D AND ASDEX-UPGRADE , 1997 .

[41]  D. Whyte,et al.  Modelling and analysis of DIII-D/DiMES sputtered impurity transport experiments , 1999 .