Experimental validation of the performance of a microreactor for the high-throughput screening of catalytic coatings

In this paper, the results of computational fluid dynamics simulations of flow, temperature, and concentration distributions used in the design of a microreactor for the high-throughput screening of catalytic coatings (Mies et al., Chem. Eng. J. 2004, 101, 225) are compared with experimental data, and good agreement is obtained in all cases. The experimental results on flow distribution were obtained from laser Doppler anemometry measurements in the range of Reynolds numbers from 6 to 113. The measured flow nonuniformity in the separate reactor compartments was below 2%. The temperature distribution was obtained from thermocouple measurements. The temperature nonuniformity between the reactor compartments was below 3 K at a maximum heat production rate of 1.3 W in ethylene oxidation at 425 °C over CuO/Al2O3/Al coatings. With respect to concentration gradients, a deviation from the average rate of reaction of only 2.3% was obtained at realistic process conditions in the ethylene ammoxidation process over identical Co -ZSM-5 coatings in all reactor compartments. The cross talking noise between separate compartments does not exceed 0.1% when the reactor parts have a smooth surface finish. This illustrates the importance of ultraprecision machining of surfaces in microtechnology, when interfaces cannot be avoided.

[1]  G. Comini,et al.  Laminar forced convection in ducts , 1979 .

[2]  L. Drain.  The Laser Doppler Technique , 1980 .

[3]  R. Gould,et al.  A Comparison of Four Velocity Bias Correction Techniques in Laser Doppler Velocimetry , 1993 .

[4]  I. Valov,et al.  Electrochemical deposition of thin zirconia films on stainless steel 316 L , 2000 .

[5]  Ferdi Schüth,et al.  The Controlled Oxidation of Hydrogen from an Explosive Mixture of Gases Using a Microstructured Reactor/Heat Exchanger and Pt/Al2O3 Catalyst , 2000 .

[6]  B. Louis,et al.  ZSM-5 coatings on stainless steel grids in one-step benzene hydroxylation to phenol by N2O: Reaction kinetics study , 2001 .

[7]  J. Chung,et al.  Electrophoretically Al-coated wire mesh and its application for catalytic oxidation of 1,2-dichlorobenzene , 2003 .

[8]  Volker Hessel,et al.  Chemical micro process engineering , 2003 .

[9]  M. Ritala,et al.  Atomic Layer Deposition of Platinum Thin Films , 2003 .

[10]  Michael J. Vasile,et al.  Focused ion beam-shaped microtools for ultra-precision machining of cylindrical components , 2003 .

[11]  F. Kapteijn,et al.  BEA coating of structured supports—performance in acylation , 2003 .

[12]  J. Richardson,et al.  Carbon dioxide reforming with Rh and Pt–Re catalysts dispersed on ceramic foam supports , 2003 .

[13]  M. Ritala,et al.  Atomic layer deposition of ruthenium thin films from Ru(thd)(3) and oxygen , 2004 .

[14]  M. D. Croon,et al.  Design of a molybdenum high throughput microreactor for high temperature screening of catalytic coatings , 2004 .

[15]  X. Verykios,et al.  Production of hydrogen for fuel cells by catalytic partial oxidation of ethanol over structured Ni catalysts , 2004 .

[16]  Edmund G Seebauer,et al.  Porous anodic alumina optimized as a catalyst support for microreactors , 2004 .

[17]  Mikko Ritala,et al.  Atomic Layer Deposition of Iridium Thin Films , 2004 .

[18]  M. D. Croon,et al.  Synthesis of molybdenum borides and molybdenum silicides in molten salts and their oxidation behavior in an air–water mixture , 2005 .

[19]  J. C. Schouten,et al.  The influence of differences between microchannels on microreactor performance , 2005 .

[20]  T. Giornelli,et al.  Grafting of VOx/TiO2 catalyst on anodized aluminum plates for structured catalytic reactors , 2005 .

[21]  M. D. Croon,et al.  Optimization of anodic oxidation and Cu-Cr oxide catalyst preparation on structured aluminum plates processed by electro discharge machining , 2005 .

[22]  Holger Löwe,et al.  Chemical micro process engineering : fundamentals, modelling and reactions , 2005 .

[23]  Preparation and characterization of bimetallic catalysts supported on mesoporous silica films , 2006 .

[24]  M. D. Croon,et al.  Design of a thick-walled screen for flow equalization in microstructured reactors , 2007 .

[25]  J. C. Jansen,et al.  Method for the in situ preparation of a single layer of zeolite Beta crystals on a molybdenum substrate for microreactor applications , 2007 .

[26]  J. C. Jansen,et al.  Hydrothermal synthesis of a continuous zeolite Beta layer by optimization of time, temperature and heating rate of the precursor mixture , 2007 .

[27]  M. D. Croon,et al.  High-throughput screening of Co-BEA and Co-ZSM-5 coatings in the ammoxidation of ethylene to acetonitrile in a microstructured reactor , 2007 .

[28]  M. D. Croon,et al.  Header design for flow equalization in microstructured reactors , 2007 .