Effects of Magnetic Field on Surface Flashover of Polyimide Film for Superconducting Magnet Insulation

Polyimide (PI) film is widely used as insulation material in superconducting magnet systems. While operating, the PI film is subjected to the interaction of electric and magnetic fields. The existence of magnetic field will affect charge behaviors leading to the changes in flashover voltage. In this paper, a steady magnetic field up to 1.2 T was applied to the PI films. The flashover voltages were investigated under DC condition and AC condition. Different angles between magnetic and electric fields were set to explore the influence of magnetic field direction on the flashover voltage of PI film. Experimental results show that the $E\times B$ drifting into the surface will block the secondary electron emission, resulting in an increase in the flashover voltage. When the $E\times B$ drifts out of the surface the result is just the opposite. The promoting effect of magnetic field on the changes of flashover voltage is weakened under the AC condition, while the suppressive effect is strengthened. The failure mechanism of PI film under strong magnetic field will provide a theoretical basis for improving the insulation reliability of superconducting magnets.

[1]  B. Du,et al.  Effects of Irradiation on Surface and Space Charge Behavior of Polyimide Film for Superconducting Magnet Insulation , 2019, 2019 2nd International Conference on Electrical Materials and Power Equipment (ICEMPE).

[2]  Hiroyuki Ohsaki,et al.  High-Temperature Superconductivity: A Roadmap for Electric Power Sector Applications, 2015–2030 , 2017, IEEE Transactions on Applied Superconductivity.

[3]  H. C. Miller.  Flashover of insulators in vacuum: the last twenty years , 2015, IEEE Transactions on Dielectrics and Electrical Insulation.

[4]  B. Du,et al.  Surface flashover characteristics of fluorinated polyimide films in liquid nitrogen , 2015, 2015 IEEE International Conference on Applied Superconductivity and Electromagnetic Devices (ASEMD).

[5]  Ying Xin,et al.  Enabling High-Temperature Superconducting Technologies Toward Practical Applications , 2014, IEEE Transactions on Applied Superconductivity.

[6]  S. Gubanski,et al.  DC flashover characteristics of a polymeric insulator in presence of surface charges , 2012, IEEE Transactions on Dielectrics and Electrical Insulation.

[7]  Ping Liu,et al.  Flashover Characteristics Along the Epoxy Resin Insulator under DC Voltage in SF6 Gas , 2012, 2012 International Conference on Computer Distributed Control and Intelligent Environmental Monitoring.

[8]  P. Fessia,et al.  Electrical and Mechanical Performance of an Enhanced Cable Insulation Scheme for Superconducting Magnets , 2010, IEEE Transactions on Applied Superconductivity.

[9]  A. Neuber,et al.  Pulsed Unipolar Surface Flashover at Atmospheric Conditions , 2006, Conference Record of the 2006 Twenty-Seventh International Power Modulator Symposium.

[10]  I. Rodin,et al.  Components of thermal and electrical insulations for the superconducting magnet systems , 2005, IEEE transactions on applied superconductivity.

[11]  B. Du,et al.  Dielectric breakdown of printed circuit board under magnetic field , 2005, Proceedings of 2005 International Symposium on Electrical Insulating Materials, 2005. (ISEIM 2005)..

[12]  S. Saito,et al.  Effect of a magnetic field on low-pressure gaseous breakdown along the surface of a solid insulator , 1991 .

[13]  M. Kristiansen,et al.  The influence of magnetic fields on dielectric surface flashover , 1990, Annual Conference on Electrical Insulation and Dielectric Phenomena.

[14]  R. A. Dougal,et al.  Mechanisms of Surface Flashover Along Solid Dielectrics in Compressed Gases: a Review , 1986, IEEE Transactions on Electrical Insulation.

[15]  S. Kobayashi,et al.  Reduction of Surface Charge-Induced Electric Field Enhancement and Increase in AC Surface Flashover Voltage , 1985, IEEE Transactions on Electrical Insulation.