Eulerian two-phase flow simulation and experimental validation of semisolid slurry generation process using cooling slope

Abstract Experimental and numerical studies of slurry generation using a cooling slope are presented in the paper. The slope having stainless steel body has been designed and constructed to produce semisolid A356 Al alloy slurry. The pouring temperature of molten metal, slope angle of the cooling slope and slope wall temperature were varied during the experiment. A multiphase numerical model, considering liquid metal and air, has been developed to simulate the liquid metal flow along the cooling channel using an Eulerian two-phase flow approach. Solid fraction evolution of the solidifying melt is tracked at different locations of the cooling channel following Schiel’s equation. The continuity, momentum and energy equations are solved considering thin wall boundary condition approach. During solidification of the melt, based on the liquid fraction and latent heat of the alloy, temperature of the alloy is modified continuously by introducing a modified temperature recovery method. Numerical simulations has been carried out for semisolid slurry formation by varying the process parameters such as angle of the cooling slope, cooling slope wall temperature and melt superheat temperature, to understand the effect of process variables on cooling slope semisolid slurry generation process such as temperature distribution, velocity distribution and solid fraction of the solidifying melt. Experimental validation performed for some chosen cases reveals good agreement with the numerical simulations.

[1]  Zongning Chen,et al.  Preparation of Semisolid A356 Alloy by a Cooling Slope Processing , 2011 .

[2]  P. Dutta,et al.  Numerical simulation of solidification of liquid aluminum alloy flowing on cooling slope , 2010 .

[3]  H. Watari,et al.  Effects of casting factors of cooling slope on semisolid condition , 2010 .

[4]  N. Saklakoğlu,et al.  Semisolid Microstructure Evolution during Cooling Slope Casting under Vibration of A380 Aluminum Alloy , 2010 .

[5]  A. Ghassemi,et al.  Study on the effects of the length and angle of inclined plate on the thixotropic microstructure of A356 aluminum alloy , 2009 .

[6]  Y. Birol.  Semi-solid processing of the primary aluminium die casting alloy A365 , 2009 .

[7]  Y. Birol.  Cooling slope casting and thixoforming of hypereutectic A390 alloy , 2008 .

[8]  H. Atkinson,et al.  Cooling slope casting to obtain thixotropic feedstock II: observations with A356 alloy , 2008 .

[9]  N. Barman,et al.  Rheological Behavior of Semi-Solid Slurry of A356 Alloy at High Shear and Cooling Rates , 2008 .

[10]  Andreas Bührig-Polaczek,et al.  A numerical study of solidification in powder injection molding process , 2008 .

[11]  M. Ferrante,et al.  On the formation of spheroidal microstructures in a semi-solid Al–Si alloy by thermomechanical processing , 2007 .

[12]  Y. Birol.  A357 thixoforming feedstock produced by cooling slope casting , 2007 .

[13]  J. Cui,et al.  Three-dimensional analysis of the modified sloping cooling/shearing process , 2007 .

[14]  W. Zhou,et al.  Semisolid microstructure of Mg2Si/Al composite by cooling slope cast and its evolution during partial remelting process , 2007 .

[15]  Helen V. Atkinson,et al.  Modelling the semisolid processing of metallic alloys , 2005 .

[16]  T. Meek,et al.  Effect of power ultrasound on solidification of aluminum A356 alloy , 2005 .

[17]  S. Kleiner,et al.  Semi‐Solid Metal Processing of Aluminum Alloy A356 and Magnesium Alloy AZ91: Comparison Based on Metallurgical Consideration , 2003 .

[18]  T. Haga.  Semisolid strip casting using a twin roll caster equipped with a cooling slope , 2002 .

[19]  Plato Kapranos,et al.  Billetless simple thixoforming process , 2002 .

[20]  Z. Fan,et al.  Semisolid metal processing , 2002 .

[21]  Shinsuke Suzuki,et al.  Casting of aluminum alloy ingots for thixoforming using a cooling slope , 2001 .

[22]  M. Suéry,et al.  Microstructural evolution during partial remelting of AlSi7Mg alloys , 1995 .

[23]  N. Zuber,et al.  Drag coefficient and relative velocity in bubbly, droplet or particulate flows , 1979 .

[24]  Zushu Hu,et al.  Trend and development of semi-solid metal processing , 2000 .