Finite element analysis of plasticity-induced fatigue crack closure: an overview

Abstract Finite element analysis is perhaps the most commonly used numerical method to model plasticity-induced fatigue crack closure. The state-of-the-art is reviewed and a comprehensive overview is presented, summarizing issues which must be considered and emphasizing potential difficulties. These include mesh refinement level, crack advancement schemes, crack shape evolution, geometry effects, and crack opening value assessment techniques.

[1]  E. Wolf.  Fatigue crack closure under cyclic tension , 1970 .

[2]  Af Grandt,et al.  Comparison of Methods for Measuring Fatigue Crack Closure in a Thick Specimen , 1988 .

[3]  J. Donald,et al.  A Procedure for Standardizing Crack Closure Levels , 1988 .

[4]  Cr Saff,et al.  Spectrum Crack Growth Prediction Method Based on Crack Surface Displacement and Contact Analyses , 1976 .

[5]  V. Oliva,et al.  FEM Analysis of Cyclic Deformation Around the Fatigue Crack Tip After a Single Overload , 1993 .

[6]  J. Newman.  A Finite-Element Analysis of Fatigue Crack Closure , 1976 .

[7]  Norman A. Fleck,et al.  Finite element analysis of plasticity-induced crack closure under plane strain conditions , 1986 .

[8]  R. Mcclung.  The influence of applied stress, crack length, and stress intensity factor on crack closure , 1991 .

[9]  Michael Ortiz,et al.  A cohesive model of fatigue crack growth , 2001 .

[10]  Kiyotsugu Ohji,et al.  On the closure of fatigue cracks under cyclic tensile loading , 1974 .

[11]  S. N. Atluri,et al.  Elastic-Plastic Analysis of Fatigue Crack Closure in Modes I and II , 1980 .

[12]  Anthony N. Palazotto,et al.  An Analytical Investigation of Plasticity Induced Closure Involving Short Cracks , 1988 .

[13]  B R Seshadri.  Numerical Simulation And Experimental Correlation Of Crack Closure Phenomenon Under Cyclic Loading , 1995 .

[14]  Ken Gall,et al.  Plastic zones and fatigue-crack closure under plane-strain double slip , 1996 .

[15]  N. A. Fleck,et al.  Effect of specimen geometry on fatigue crack growth in plane strain. I - Constant amplitude response. II - Overload response , 1990 .

[16]  Kiyotsugu Ohji,et al.  Cyclic analysis of a propagating crack and its correlation with fatigue crack growth , 1975 .

[17]  Hideo Kobayashi,et al.  FINITE ELEMENT ANALYSIS OF FATIGUE CRACK CLOSURE IN COMPACT SPECIMEN , 1984 .

[18]  S. Park,et al.  Simulation of Fatigue Crack Closure Behavior Under Variable-Amplitude Loading by a 2D Finite Element Analysis Based on the Most Appropriate Mesh Size Concept , 1999 .

[19]  J. Rice,et al.  Limitations to the small scale yielding approximation for crack tip plasticity , 1974 .

[20]  Andrew H. Sherry,et al.  COMPENDIUM OF T‐STRESS SOLUTIONS FOR TWO AND THREE DIMENSIONAL CRACKED GEOMETRIES , 1995 .

[21]  Thomas Siegmund,et al.  Simulation of interface fatigue crack growth via a fracture process zone model , 2001 .

[22]  Kiyotsugu Ohji,et al.  Fatigue crack growth under biaxial loading , 1974 .

[23]  Ji-Ho Song,et al.  DETERMINATION OF THE MOST APPROPRIATE MESH SIZE FOR A 2‐D FINITE ELEMENT ANALYSIS OF FATIGUE CRACK CLOSURE BEHAVIOUR , 1997 .

[24]  Fernand Ellyin,et al.  A study of fatigue crack closure by elastic-plastic finite element analysis for constant-amplitude loading , 1996 .

[25]  Subra Suresh,et al.  Fatigue crack deflection and fracture surface contact: Micromechanical models , 1985 .

[26]  Jc Newman.  Finite-Element Analysis of Crack Growth Under Monotonic and Cyclic Loading , 1977 .

[27]  John W. Hutchinson,et al.  Analysis of Closure in Fatigue Crack Growth , 1978 .

[28]  J. Newman,et al.  Three-Dimensional Finite-Element Simulation of Fatigue Crack Growth and Closure , 1988 .

[29]  Huseyin Sehitoglu,et al.  Fatigue Crack Closure Outside a Small-Scale Yielding Regime , 1988 .

[30]  Donald R. Houser,et al.  An elastic-plastic analytical model for predicting fatigue crack growth in arbitrary edge-cracked two-dimensional geometries with residual stress , 1994 .

[31]  Kiran Solanki,et al.  A new methodology for computing crack opening values from finite element analyses , 2004 .

[32]  B. Dattaguru,et al.  EXPERIMENTAL AND ANALYTICAL ESTIMATES OF FATIGUE CRACK CLOSURE IN AN ALUMINIUM‐COPPER ALLOY PART II: A FINITE ELEMENT ANALYSIS , 1997 .

[33]  A. Kfouri,et al.  An elastic-plastic finite element analysis of a compact tension specimen , 1983 .

[34]  R. O. Ritchie,et al.  Fatigue crack propagation in aluminum-lithium alloy 2090: Part II. small crack behavior , 1988 .

[35]  S. Atluri,et al.  FATIGUE CRACK CLOSURE AND DELAY EFFECTS UNDER MODE I SPECTRUM LOADING: AN EFFICIENT ELASTIC–PLASTIC ANALYSIS PROCEDURE , 1979 .

[36]  S. R. Daniewicz,et al.  An assessment of geometry effects on plane stress fatigue crack closure using a modified strip-yield model , 1996 .

[37]  Norman A. Fleck,et al.  EFFECT OF SPECIMEN GEOMETRY ON FATIGUE CRACK GROWTH IN PLANE STRAIN—II. OVERLOAD RESPONSE , 1990 .

[38]  Kiran Solanki,et al.  Finite element modeling of plasticity-induced crack closure with emphasis on geometry and mesh refinement effects , 2003 .

[39]  J. Schijve,et al.  CRACK OPENING STRESS MEASUREMENTS OF SURFACE CRACKS IN 7075‐T6 ALUMINIUM ALLOY PLATE SPECIMEN THROUGH ELECTRON FRACTOGRAPHY , 1992 .

[40]  Ogura Keui,et al.  FEM analysis of crack closure and delay effect in fatigue crack growth under variable amplitude loading , 1977 .

[41]  Je Allison,et al.  A Comparison of Measurement Methods and Numerical Procedures for the Experimental Characterization of Fatigue Crack Closure , 1988 .

[42]  R. C. McClung,et al.  CLOSURE AND GROWTH OF MODE I CRACKS IN BIAXIAL FATIGUE , 1989 .

[43]  T. Hughes.  Generalization of selective integration procedures to anisotropic and nonlinear media , 1980 .

[44]  J. Newman.  A crack-closure model for predicting fatigue crack growth under aircraft spectrum loading , 1981 .

[45]  A. F. Grandt,et al.  Three-dimensional crack closure behavior , 1990 .

[46]  Michael A. Sutton,et al.  Determining Fatigue Crack Opening Loads from Near-Crack-Tip Displacement Measurements , 1999 .

[47]  S. R. Daniewicz,et al.  Simulation of plasticity-induced fatigue crack closure in part-through cracked geometries using finite element analysis , 2002 .

[48]  E Bednarz,et al.  A Finite-Element Investigation of Viscoplastic-Induced Closure of Short Cracks at High Temperatures , 1989 .

[49]  Anders Blom,et al.  An experimental and numerical study of crack closure , 1985 .

[50]  Anthony W. Thompson,et al.  Roughness-Induced Crack Closure: An Explanation for Microstructurally Sensitive Fatigue Crack Growth , 1983 .

[51]  James C. Newman,et al.  Finite-element analyses and fracture simulation in thin-sheet aluminum alloy , 1992 .

[52]  R. C. McClung,et al.  FINITE ELEMENT ANALYSIS OF SPECIMEN GEOMETRY EFFECTS ON FATIGUE CRACK CLOSURE , 1994 .

[53]  A. J. Carlsson,et al.  Influence of non-singular stress terms and specimen geometry on small-scale yielding at crack tips in elastic-plastic materials , 1973 .

[54]  J. C. Rice,et al.  On numerically accurate finite element solutions in the fully plastic range , 1990 .

[55]  John R. Rice,et al.  Mechanics of Crack Tip Deformation and Extension by Fatigue , 1967 .

[56]  Wei Sun,et al.  Modeling of plane strain fatigue crack closure , 1991 .

[57]  Robert H. Dodds,et al.  Three-dimensional effects on fatigue crack closure in the small-scale yielding regime – a finite element study , 2003 .

[58]  A. F. Blom,et al.  Fatigue crack growth and closure behaviour of semicircular and semi-elliptical surface flaws , 1993 .

[59]  Kiyotsugu Ohji,et al.  INFLUENCE OF MECHANICAL FACTORS ON THE FATIGUE CRACK CLOSURE , 1977 .

[60]  R. Mcclung,et al.  Fatigue Crack Closure and Crack Growth Outside the Small Scale Yielding Regime , 1988 .

[61]  V. Sánchez Gálvez,et al.  Modelling plasticity-induced fatigue crack closure , 1990 .

[62]  P. Bowen,et al.  On the finite element simulation of three-dimensional semi-circular fatigue crack growth and closure , 1998 .

[63]  Sylvie Pommier,et al.  Plane strain crack closure and cyclic hardening , 2002 .

[64]  A. F. Blom,et al.  Variation of crack-opening stresses in three-dimensions - Finite thickness plate , 1991 .

[65]  N. Fleck,et al.  Analysis of Crack Closure Under Plane Strain Conditions , 1988 .

[66]  Robert McClung,et al.  On the finite element analysis of fatigue crack closure—1. Basic modeling issues , 1989 .

[67]  J. Newman,et al.  Stress-intensity factor equations for cracks in three-dimensional finite bodies subjected to tension and bending loads , 1984 .

[68]  Jeffrey David Skinner.  Finite Element Analysis of Plasticity-Induced Fatigue Crack Closure in Three-Dimensional Cracked Geometries , 2001 .

[69]  Ken Gall,et al.  FEM study of fatigue crack closure under double slip , 1996 .

[70]  J. Padovan,et al.  Fatigue crack propagation and closure behavior of modified 1070 steel: Finite element study , 1997 .

[71]  R. C. McClung,et al.  On the finite element analysis of fatigue crack closure—2. Numerical results , 1989 .

[72]  B. H. Thacker,et al.  Finite element visualization of fatigue crack closure in plane stress and plane strain , 1991, International Journal of Fracture.

[73]  Stavros Syngellakis,et al.  Numerical modelling of combined roughness and plasticity induced crack closure effects in fatigue , 2000 .

[74]  S. R. Daniewicz,et al.  Determination of the opening load for a growing fatigue crack: evaluation of experimental data reduction techniques and analytical models , 2002 .

[75]  Tetsuro Shiraishi,et al.  FATIGUE CRACK GROWTH AND CLOSURE AT HIGH STRESS RATIOS , 1995 .

[76]  S. R. Daniewicz,et al.  Finite element modeling of microstructurally small cracks using single crystal plasticity , 2003 .