Model-based determination of nonlinear material parameters of metals with low melting points

An alternative way of determining the temperature-dependent characteristics of metals is presented. The method that is relatively simple and cheap is suitable mainly for metals with lower melting points. The paper starts with the experimental investigation of the melting process of the Field metal in an induction furnace, which provides all necessary information for determining the above material characteristics. These data are then used for a coupled numerical simulation of the process of heating and melting and also for sensitivity analysis and model-based determining of specific heat capacity. The results are again verified by measurements, with a very good agreement.

[1]  Chang Liu,et al.  Development of a Latchable Microvalve Employing a Low-Melting-Temperature Metal Alloy , 2008, Journal of Microelectromechanical Systems.

[2]  Liu Yanping,et al.  Numerical analysis for induction heating process of ferromagnetic materials , 2012 .

[3]  E. H. Buyco,et al.  Thermophysical properties of matter - the TPRC data series. Volume 5. Specific heat - nonmetallic solids. (Reannouncement). Data book , 1970 .

[4]  Fabio Giulii Capponi,et al.  Axial-Flux Permanent-Magnet Generator for Induction Heating Gensets , 2010, IEEE Transactions on Industrial Electronics.

[5]  J. Acero,et al.  Series resonant multi-inverter with discontinuous-mode control for improved light-load operation , 2010, IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society.

[6]  A. K. M. Nurul Amin,et al.  Thermally-assisted end milling of titanium alloy Ti-6Al-4V using induction heating , 2013 .

[7]  Luis Angel Barragan,et al.  Series Resonant Multiinverter with Discontinuous-Mode Control for Improved Light-Load Operation , 2011, IEEE Transactions on Industrial Electronics.

[8]  J. M. Coulson,et al.  Heat Transfer , 2018, A Concise Manual of Engineering Thermodynamics.

[9]  Fabrizio Dughiero,et al.  Magnetic Field Synthesis in the Design of Inductors for Magnetic Fluid Hyperthermia , 2010, IEEE Transactions on Magnetics.

[10]  Pavel Kůs,et al.  Numerical solution of coupled problems using code Agros2D , 2013, Computing.

[11]  Oscar Lucía,et al.  Computational Modeling of Two Partly Coupled Coils Supplied by a Double Half-Bridge Resonant Inverter for Induction Heating Appliances , 2013, IEEE Transactions on Industrial Electronics.

[12]  Valery Rudnev,et al.  Handbook of Induction Heating , 2002 .

[13]  J. Acero,et al.  Magnetic vector potential based model for eddy-current loss calculation in round-wire planar windings , 2006, IEEE Transactions on Magnetics.

[15]  L. A. Barragan,et al.  Modeling of Planar Spiral Inductors Between Two Multilayer Media for Induction Heating Applications , 2006, IEEE Transactions on Magnetics.

[16]  Pascal Maussion,et al.  Induction Heating Technology and Its Applications: Past Developments, Current Technology, and Future Challenges , 2014, IEEE Transactions on Industrial Electronics.

[17]  Song-Yop Hahn,et al.  Determination of levitated molten metal shape in axisymmetric induction heating system using sensitivity analysis , 1995 .

[18]  E. Davies.  Conduction and Induction Heating , 1990 .

[19]  S. Lupi,et al.  Experimental and Numerical Analysis of DC Induction Heating of Aluminum Billets , 2009, IEEE Transactions on Magnetics.

[20]  J. Swinburne.  Electromagnetic Theory , 1894, Nature.

[21]  Kevin Barraclough,et al.  I and i , 2001, BMJ : British Medical Journal.

[22]  Yannick Tillier,et al.  Identification of magnetic parameters by inverse analysis coupled with finite-element modeling , 2002 .

[23]  R. C. Mackenzie,et al.  Nomenclature in thermal analysis, Part IV , 1972 .