Effects of Jointed Rock Mass and Mixed Ground Conditions on the Cutting Efficiency and Cutter Wear of Tunnel Boring Machine

The cutting efficiency and wear of tunnel boring machine (TBM) cutters are two important parameters commonly used to estimate the boring performance and lifetime of the TBM in the tunneling process. These problems have been investigated by several researchers, whereas the influence of jointed rock mass and mixed ground condition on the cutting efficiency and cutter wear remains insufficiently understood. This study aims to elucidate the influence of rock mass and ground parameters on the cutting efficiency and cutter wear of the TBM by conducting a series of newly developed rolling boring tests on prefabricated joint sandstone samples with different orientations, spacings, and interlayers. Moreover, a numerical simulation is implemented through ANSYS software to verify the rationality of experimental results. The experimental and numerical results indicate that the optimal joint orientation is 30° for the TBM to intrude into a jointed rock mass. As joint spacing increases, the cutting efficiency decreases and the cutter wear increases. Furthermore, specific energy (SE) and cutter wear simultaneously reach their maximum values when the rock abrasivity index (RAI) is 60. Both the specific energy and cutter wear decrease with increasing specific strength. For the rock mass with a soft interlayer in mixed ground, the optimal dip angle is 45°. Additionally, the fitting formulas of SE and cutter wear in mixed ground are proposed to quantitatively illustrate the effect of RAI and interlayer strength on the cutting efficiency and cutter wear. The present study provides an improved understanding of rock-breaking mechanics, thereby making it possible for designers to adjust their design to enhance the TBM cutting efficiency.

[1]  J. Rostami,et al.  A New Model for Performance Prediction of Hard Rock Tbms , 1997 .

[2]  Sung O. Choi,et al.  Numerical study to estimate the cutting power on a disc cutter in jointed rock mass , 2016 .

[3]  G. Exadaktylos,et al.  A spatial estimation model for continuous rock mass characterization from the specific energy of a TBM , 2008 .

[4]  Jamal Rostami,et al.  Performance Assessment of Hard Rock TBM and Rock Boreability Using Punch Penetration Test , 2016, Rock Mechanics and Rock Engineering.

[5]  Liang Meng,et al.  Wear analysis of disc cutters of full face rock tunnel boring machine , 2014 .

[6]  Yilan Kang,et al.  The energy method to predict disc cutter wear extent for hard rock TBMs , 2012 .

[7]  Amund Bruland,et al.  HARD ROCK TUNNEL BORING , 2000 .

[8]  R. Teale.  The concept of specific energy in rock drilling , 1965 .

[9]  J. Barbera,et al.  Contact mechanics , 1999 .

[10]  Charalampos Saroglou,et al.  Prediction of TBM performance in mixed-face ground conditions , 2017 .

[11]  Ralf J. Plinninger.  Hardrock abrasivity investigation using the Rock Abrasivity Index (RAI) , 2010 .

[12]  Qiuming Gong,et al.  Case studies of TBM tunneling performance in rock-soil interface mixed ground , 2013 .

[13]  Lijun Yin,et al.  TBM tunneling in mixed-face ground: Problems and solutions , 2015 .

[14]  Xiao-Ping Zhang,et al.  A Wear Rule and Cutter Life Prediction Model of a 20-in. TBM Cutter for Granite: A Case Study of a Water Conveyance Tunnel in China , 2017, Rock Mechanics and Rock Engineering.

[15]  Jian Zhao,et al.  Introduction of an empirical TBM cutter wear prediction model for pyroclastic and mafic igneous rocks; a case history of Karaj water conveyance tunnel, Iran , 2014 .

[16]  Xiaoping Zhou,et al.  Analysis on the damage behavior of mixed ground during TBM cutting process , 2016 .

[17]  Jafar Khademi Hamidi,et al.  Simultaneous Effects of Joint Spacing and Orientation on TBM Cutting Efficiency in Jointed Rock Masses , 2013, Rock Mechanics and Rock Engineering.

[18]  Jamal Rostami,et al.  Application of non-linear regression analysis and artificial intelligence algorithms for performance prediction of hard rock TBMs , 2016 .

[19]  Jian Zhao,et al.  Numerical modelling of the effects of joint spacing on rock fragmentation by TBM cutters , 2005 .

[20]  Qian Zhang,et al.  Development of a prediction model for the wear evolution of disc cutters on rock TBM cutterhead , 2017 .