A Battery-Less BLE IoT Motion Detector Supplied by 2.45-GHz Wireless Power Transfer

Wireless power transfer (WPT) is a possible way to achieve cheap, rapid and large-scale deployment of battery-less IoT smart sensors. However, the key challenge in designing WPT-supplied smart sensors is to ensure that the harvested power is higher than the consumed power in presence of strong WPT path loss. This paper presents the design and optimization of a smart sensor supplied by 2.45-GHz RF power and performing infrared-based motion detection and Bluetooth Low Energy (BLE) communication. The full system (RF energy harvester, power management, sensor transducer and interface, control, data processing and wireless transmission) is implemented using low-power off-the-shelf components. In the sensing sub-system, low average power is achieved using efficient duty-cycling of the analog front-end. In the harvesting sub-system, architecture choice and design of the matching network and rectifier circuit allow to optimize the total power harvesting efficiency (PHE). The implemented smart sensor can operate reliably with an incident RF power as low as −10.9 dBm. The sensing sub-system exhibits an average power of 4.3 μW and a maximum number of transmitted event packets of 60 packets per hour.

[1]  David Bol,et al.  Can we connect trillions of IoT sensors in a sustainable way? A technology/circuit perspective (Invited) , 2015, 2015 IEEE SOI-3D-Subthreshold Microelectronics Technology Unified Conference (S3S).

[2]  Eider Goikolea,et al.  Review on supercapacitors: Technologies and materials , 2016 .

[3]  Luc Vandendorpe,et al.  On the Effect of Blockage Objects in Dense MIMO SWIPT Networks , 2018, IEEE Transactions on Communications.

[4]  Denis Flandre,et al.  Efficient passive energy harvesters at 950 MHz and 2.45 GHz for 100 μW applications in 65 nm CMOS , 2016, 2016 IEEE International Conference on Electronics, Circuits and Systems (ICECS).

[5]  Mahmoud Shuker Mahmoud,et al.  A Study of Efficient Power Consumption Wireless Communication Techniques/ Modules for Internet of Things (IoT) Applications , 2016, IoT 2016.

[6]  Guido Dolmans,et al.  A 900 MHz RF energy harvesting system in 40 nm CMOS technology with efficiency peaking at 47% and higher than 30% over a 22dB wide input power range , 2017, ESSCIRC 2017 - 43rd IEEE European Solid State Circuits Conference.

[7]  David Bol,et al.  A 0.48mm2 5μW-10mW indoor/outdoor PV energy-harvesting management unit in a 65nm SoC based on a single bidirectional multi-gain/multi-mode switched-cap converter with supercap storage , 2015, ESSCIRC Conference 2015 - 41st European Solid-State Circuits Conference (ESSCIRC).

[8]  Wouter A. Serdijn,et al.  Co-Design of a CMOS Rectifier and Small Loop Antenna for Highly Sensitive RF Energy Harvesters , 2014, IEEE Journal of Solid-State Circuits.

[9]  Giuseppe Palmisano,et al.  A 90-nm CMOS Threshold-Compensated RF Energy Harvester , 2011, IEEE Journal of Solid-State Circuits.

[10]  Dusan M. Milosevic,et al.  An RF-to-DC energy harvester for co-integration in a low-power 2.4 GHz transceiver frontend , 2012, 2012 IEEE International Symposium on Circuits and Systems.

[11]  Soumyajit Mandal,et al.  Low-Power CMOS Rectifier Design for RFID Applications , 2007, IEEE Transactions on Circuits and Systems I: Regular Papers.

[12]  David E. Culler,et al.  Perpetual environmentally powered sensor networks , 2005, IPSN 2005. Fourth International Symposium on Information Processing in Sensor Networks, 2005..