MODELING THE INFLUENCE OF SURFACE EFFECT ON INSTABILITY OF NANO-CANTILEVER IN PRESENCE OF VAN DER WAALS FORCE

Surface effect often plays a significant role in the pull-in performance of nano-electromechanical systems (NEMS) but limited works have been conducted for taking this effect into account. Herein, the influence of surface effect has been investigated on instability behavior of cantilever nano-actuator in the presence of van der Waals force (vdW). Three different methods, i.e. an analytical modified Adomian decomposition (MAD), Lumped parameter model (LPM) and numerical solution have been applied to solve the governing equation of the system. The results demonstrate that surface effect reduces the pull-in voltage of the system. Moreover, surface energy causes the cantilever nano-actuator with the assigned parameter to deflect as a softer structure. It is found that while surface effect becomes important for low values of the cantilever nano-actuator thickness, vdW attraction is significant for low initial gap values. Surprisingly, the increase in the initial gap, enhances the contribution of surface effect in pull-in instability of the system while reduces the contribution of vdW attraction. Furthermore, the minimum initial gap and the detachment length of the cantilever nano-actuator that does not stick to the substrate due to vdW force and surface effect has been approximated. A good agreement has been observed between the values of instability parameters predicted via these three methods. Whilst compared to the instability voltage predicted by numerical solution, the pull-in voltage obtained by MAD series and LPM method is overestimated and underestimated, respectively.

[1]  Raj K. Gupta,et al.  Electrostatic pull-in test structure design for in-situ mechanical property measurements of microelectromechanical systems (MEMS) , 1997 .

[2]  Mohamadreza Abadyan,et al.  Influence of surface effects on size-dependent instability of nano-actuators in the presence of quantum vacuum fluctuations , 2012 .

[3]  J. Israelachvili.  Intermolecular and surface forces , 1985 .

[4]  R. Puers,et al.  A physical model to predict stiction in MEMS , 2006 .

[5]  Mohamadreza Abadyan,et al.  Modeling the effects of size dependence and dispersion forces on the pull-in instability of electrostatic cantilever NEMS using modified couple stress theory , 2011 .

[6]  Ling Wen-hui,et al.  Dynamic Behaviour of Nanoscale Electrostatic Actuators , 2003 .

[7]  Jin He,et al.  Surface effect on the elastic behavior of static bending nanowires. , 2008, Nano letters.

[8]  Morton E. Gurtin,et al.  Surface stress in solids , 1978 .

[10]  H. Haddadpour,et al.  Investigating the effect of Casimir and van der Waals attractions on the electrostatic pull-in instability of nano-actuators , 2010 .

[11]  G. J. Maclay,et al.  The anharmonic Casimir oscillator (ACO)-the Casimir effect in a model microelectromechanical system , 1995 .

[12]  N. Aluru,et al.  Calculation of pull-in voltages for carbon-nanotube-based nanoelectromechanical switches , 2002 .

[13]  Randolph Rach,et al.  A convenient computational form for the Adomian polynomials , 1984 .

[14]  Xi-Qiao Feng,et al.  Surface effects on buckling of nanowires under uniaxial compression , 2009 .

[15]  Abdul-Majid Wazwaz,et al.  The numerical solution of sixth-order boundary value problems by the modified decomposition method , 2001, Appl. Math. Comput..

[16]  ALI H. NAYFEH,et al.  Reduced-Order Models for MEMS Applications , 2005 .

[17]  A. Alasty,et al.  Closed-form solutions of the pull-in instability in nano-cantilevers under electrostatic and intermolecular surface forces , 2007 .

[18]  N. Pugno,et al.  Nanoelectromechanical Systems: Devices and Modeling , 2006 .

[19]  S. Asokanthan,et al.  Influence of surface effects on the pull-in instability of NEMS electrostatic switches , 2010, Nanotechnology.

[20]  Ai Qun Liu,et al.  Mechanical design and optimization of capacitive micromachined switch , 2001 .

[21]  Morton E. Gurtin,et al.  A continuum theory of elastic material surfaces , 1975 .

[22]  Robert Puers,et al.  Pull-in voltage analysis of electrostatically actuated beam structures with fixed–fixed and fixed–free end conditions , 2002 .

[23]  W. Miller,et al.  A closed-form model for the pull-in voltage of electrostatically actuated cantilever beams , 2005 .

[24]  S. K. Georgantzinos,et al.  Carbon nanotube-based resonant nanomechanical sensors: A computational investigation of their behavior , 2010 .

[25]  Yiming Fu,et al.  Size-dependent pull-in phenomena in electrically actuated nanobeams incorporating surface energies , 2011 .