Development of a partition panel of an Al6061 sheet metal part for the improvement of formability and mechanical properties by hot forming quenching

In this study, the hot forming quenching process was investigated to improve the deficiencies that arise in materials subjected to conventional cold stamping, such as low formability and undesirable mechanical properties. The hot forming quenching process was mainly discussed in terms of formability and mechanical properties in this study and was first evaluated by preliminary tests. To examine formability, an evaluation was conducted using hot-tensile and hemispherical-dome stretching tests at temperatures of 350°C and 450°C, respectively. In addition, the mechanical properties of the formed part were predicted using quench factor analysis, which was based on the cooling temperature during the die quenching process. These preliminary test results were then used to predict the formability and hardness of the partition panel of an automotive part, where the analytical results indicated high performance of the hot forming quenching process, in contrast to conventional forming. Finally, the hot forming quenching experiment of the partition panel was carried out to validate the predicted results and the obtained formability and hardness values were compared with conventional forming at room temperature using T4 and T6 heat-treated sheets. The analytical and experimental results indicate that the hot forming quenching process is a very effective method for obtaining desirable formability and mechanical properties in the forming of aluminum sheets.

[1]  Amit K. Ghosh,et al.  Biaxial warm forming behavior of aluminum sheet alloys , 2003 .

[2]  Ghassan T. Kridli,et al.  Formability prediction of aluminum sheet alloys under isothermal forming conditions , 2015 .

[3]  Giuseppe Ingarao,et al.  Sustainability issues in sheet metal forming processes: an overview , 2011 .

[4]  Ken-ichiro Mori,et al.  Finite element simulation of warm deep drawing of aluminium alloy sheet when accounting for heat conduction , 2002 .

[5]  Byung-Min Kim,et al.  Application of QFA coupled with CFD analysis to predict the hardness of T6 heat treated Al6061 cylinder , 2013 .

[6]  Murat Buyuk,et al.  Development of a High Strain-Rate Dependent Vehicle Model , 2005 .

[7]  Baoyu Wang,et al.  Forming defects in aluminum alloy hot stamping of side-door impact beam , 2014 .

[8]  P. Friedman,et al.  Warm forming behavior of high strength aluminum alloy AA7075 , 2012 .

[9]  John D. Bernardin,et al.  Validation of the quench factor technique in predicting hardness in heat treatable aluminum alloys , 1995 .

[10]  Muammer Koç,et al.  Investigations on forming of aluminum 5052 and 6061 sheet alloys at warm temperatures , 2010 .

[11]  M. Maniruzzaman,et al.  A Methodology to Predict the Effects of Quench Rates on Mechanical Properties of Cast Aluminum Alloys , 2007 .

[12]  Young Hoon Moon,et al.  Tool temperature control to increase the deep drawability of aluminum 1050 sheet , 2001 .

[13]  J. Huetink,et al.  Simulation of aluminium sheet forming at elevated temperatures , 2006 .

[14]  Peng Lin,et al.  Investigation on strengthening of 6A02 aluminum alloy sheet in hot forming-quenching integrated process with warm forming-dies , 2013 .

[15]  Knut Marthinsen,et al.  Effect of quenching rate on microstructure and mechanical properties of commercial AA7108 aluminium alloy , 2012 .

[16]  Alistair Foster,et al.  Investigation of deformation and failure features in hot stamping of AA6082: Experimentation and modelling , 2012 .

[17]  G. Cowper,et al.  STRAIN-HARDENING AND STRAIN-RATE EFFECTS IN THE IMPACT LOADING OF CANTILEVER BEAMS , 1957 .

[18]  J. T. Staley,et al.  Kinetics of precipitation in aluminum alloys during continuous cooling , 1974, Metallurgical and Materials Transactions B.

[19]  Muammer Koç,et al.  Numerical investigations on springback characteristics of aluminum sheet metal alloys in warm forming conditions , 2008 .

[20]  Manoj Kumar,et al.  Investigations on warm forming of AW-7020-T6 alloy sheet , 2014 .

[21]  Mohammad Riahi,et al.  Analysis of transient temperature and residual thermal stresses in friction stir welding of aluminum alloy 6061-T6 via numerical simulation , 2011 .

[22]  Seyed Mojtaba Zebarjad,et al.  Prediction of hardness at different points of Jominy , 2008 .

[23]  Faramarz Djavanroodi,et al.  Experimental and numerical evaluation of forming limit diagram for Ti6Al4V titanium and Al6061-T6 aluminum alloys sheets , 2010 .

[24]  Fahrettin Ozturk,et al.  Review of warm forming of aluminum-magnesium alloys , 2008 .