Modeling of IT-SOFC with indirect internal reforming operation fueled by methane: Effect of oxygen a

Mathematical models of an Intermediate Temperature Solid Oxide Fuel Cell (IT-SOFC) with indirect internal reforming operation (IIR-SOFC) fueled by methane were developed. The models were based on a steady-state heterogeneous two-dimensional tubular-design SOFC. The benefit in adding oxygen to methane and steam as the feed for autothermal reforming reaction on the thermal behavior and SOFC performance was simulated. The results indicated that smoother temperature gradient with lower local cooling at the entrance of the reformer channel can be achieved by adding a small amount of oxygen. However, the electrical efficiency noticeably decreased when too high oxygen content was added due to the loss of hydrogen generation from the oxidation reaction; hence, the inlet oxygen to carbon (O/C) molar ratio must be carefully controlled. Another benefit of adding oxygen is the reduction of excess steam requirement, which could reduce the quantity of heat required to generate the steam and eventually increases the overall system performance. It was also found that the operating temperature strongly affects the electrical efficiency achievement and temperature distribution along the SOFC system. By increasing the operating temperature, the system efficiency increases but a significant temperature gradient is also detected. The system with a counter-flow pattern was compared to that with a co-flow pattern. The co-flow pattern provided smoother temperature gradient along the system due to better matching between the heat supplied from the electrochemical reaction and the heat required for the steam reforming reaction. However, the electrical efficiency of the co-flow pattern is lower due to the higher cell polarization at a lower system temperature.

[1]  S. Chan,et al.  Autothermal reforming of methane gas—Modelling and experimental validation , 2008 .

[2]  N. Sammes,et al.  Dynamic modeling of single tubular SOFC combining heat/mass transfer and electrochemical reaction effects , 2005 .

[3]  S. Gudlavalleti,et al.  Thermal sintering studies of an autothermal reforming catalyst , 2007 .

[4]  Ivar M. Dahl,et al.  Carbon dioxide reforming of methane over lanthanum-modified catalysts in a fluidized-bed reactor , 1994 .

[5]  S. Assabumrungrat,et al.  Modeling of SOFC with indirect internal reforming operation: Comparison of conventional packed-bed and catalytic coated-wall internal reformer , 2009 .

[6]  L. Kershenbaum,et al.  Modelling of an indirect internal reforming solid oxide fuel cell , 2002 .

[7]  M. Khaleel,et al.  A finite element analysis modeling tool for solid oxide fuel cell development: coupled electrochemistry, thermal and flow analysis in MARC® , 2004 .

[8]  S. D. Souza Thin-film solid oxide fuel cell with high performance at low-temperature , 1997 .

[9]  Hwan Moon,et al.  Performance and durability of Ni-coated YSZ anodes for intermediate temperature solid oxide fuel cells , 2006 .

[10]  Robert J. Kee,et al.  Anode barrier layers for tubular solid-oxide fuel cells with methane fuel streams , 2006 .

[11]  M. Bradford,et al.  Catalytic reforming of methane with carbon dioxide over nickel catalysts II. Reaction kinetics , 1996 .

[12]  Hee Chun Lim,et al.  Studies of the effects of the reformer in an internal-reforming molten carbonate fuel cell by mathematical modeling , 2002 .

[13]  S. Chan,et al.  Kinetic and modelling study of methane steam reforming over sulfide nickel catalyst on a gamma alumina support , 2005 .

[14]  David Chadwick,et al.  Achieving Autothermal Operation in Internally Reformed Solid Oxide Fuel Cells: Simulation Studies , 2005 .

[15]  G. Froment,et al.  Methane steam reforming, methanation and water‐gas shift: I. Intrinsic kinetics , 1989 .

[16]  Ryuji Kikuchi,et al.  Catalytic autothermal reforming of methane and propane over supported metal catalysts , 2003 .

[17]  Paola Costamagna,et al.  Electrochemical model of the integrated planar solid oxide fuel cell (IP-SOFC) , 2004 .